What chargers can you use to charge your iPhone? Simple rules! Video: how to use wireless charging for iPhone. Decrease screen brightness

We have all encountered a situation where the charge of a smartphone begins to decrease right before our eyes. Many will decide that it’s time to change the battery, and some will think about the reasons fast discharge batteries. And the latter will be right, since knowledge about correct operation batteries will extend the battery life for years.

How to properly charge Apple devices

It would seem that everything is simple - you insert the charger cable into the gadget and into the power supply, and electricity will do the rest of the work. However, this is misleading and recharging your device in this way can harm the battery.

Manufacturers and specialists, through research, trial and error, have created a number of recommended operating rules iPhone batteries, iPad and iPod. This also applies to other devices whose batteries are based on lithium-ion.

Carry out a full discharge-charge cycle of your phone no more than once a month. To do this, you need to completely deplete the battery reserves, then start the charging process, and, without turning on the device, bring the charge level to 100%.
Charge your phone as often as possible. The recommended battery level should be kept between 40-80%. Frequent charging- this is the movement of electrons inside the battery and the absence of the possibility of rendering energy-intensive elements unusable.
Do not bring the battery charge to 100% (except for the cases described in the first paragraph). Your device runs on battery power, not mains power. Upon reaching maximum charge the battery continues to be used, and this leads to its discharge by 1% or less, which starts the charging process again. Such microscopic charging of the battery harms it, so it is not recommended to leave your device to recharge all night or all day.
Observe temperature regime, especially while charging the phone. Increasing and cooling temperatures lead to physical deformation of battery cells. Optimal temperature For active use and charging gadgets fluctuates in the range of 20–24°C.

Is it possible to charge an iPhone using an iPad charger?

There is no prohibition against using “foreign” charger cables to power your iPhone. But it is worth remembering that the plug must fit the phone connector. For example, it is highly not recommended to try to charge an iPhone using a charging cable from a thin Nokia and other plugs that are not suitable for this purpose. You also need an operating voltage of 5V, but this is the international standard.

The charging output voltage for iPhone, iPod and iPad is the same and is equal to the operating voltage of the USB port - +5V. What is written on the charger is the maximum current it can produce. But that doesn't mean she always gives him away. Any Apple device has special processor charge, which optimally selects the current to charge the battery. He also limits charging current on a certain maximum level if the battery is very discharged. The only difference is that the iPad's battery is larger than the iPhone's and therefore, to reduce charging time, the iPad's maximum charging current is 2A instead of the iPhone's 1A. Naturally Charger must provide this current. That's why it's more powerful on the iPad. As a result, the iPhone can be safely charged by charging from the iPad, since the charging current Iphone smaller than the charger can produce. By the way, charge it the other way around iPad charging It’s also possible from an iPhone, it’s just that the charge will be 2 times slower, since charging Iphone cannot produce the required 2A.

https://uip.me/forum/index.php?showtopic=12653

How to charge your phone from a computer, in a car or on a train

The charger is divided into two parts: a power supply and a cable with a USB connector. As a result, anything that has a USB input and is connected to a power source can charge your device.

The most simple example are computers and laptops. You need to connect the devices using a charging cable and wait for the required charge level. It is important to remember that a laptop that is turned off or in sleep mode will not charge the smartphone. Although for sleep mode this function can be disabled:

Click right click mouse over the “Computer” icon and select “Management” from the drop-down menu. Through the context menu of the “Computer” icon, go to “Management”
In the left column, click on “Device Manager”.
Open the tab " USB controllers».
In "Device Manager" find "USB Controllers"
Double-click the left mouse button to open the properties of each item called “USB Root Hub”. Double click Left-click to open the properties of “USB Root Hub”
Go to the “Power Management” tab and uncheck the “Allow the computer to turn off this device to save energy” checkbox. And confirm the change with the “OK” button. Uncheck "Allow the computer to turn off this device to save energy" and save the changes

Now your laptop will charge smartphones and tablets even in sleep mode.

When it comes to cars, not many of them have direct facilities for charging your phones. But almost all of them have cigarette lighters, which means that with the help of a simple device called a “bullet,” you can connect the phone to a power source.

Using a cigarette lighter adapter, you can charge your smartphone in the car.

The possibility of using the electrical network in trains is fully realized. Each carriage, be it a reserved seat, a compartment or a SV, has the most ordinary sockets. Of course, their voltage varies within a certain range, and this affects the charging speed of the gadget. The main thing is that you only need a cable and network adapter to start charging the device's battery.

With help standard set To charge, you can recharge your phone on the train

How to use wireless charging

Not the best new technology, which only recently found application in the charging system for portable devices. If we omit the unclear terminology, wireless phone charging is based on the principle of inductance.

The wireless charger consists of two parts:

As a result, we get a phone case with which a magnetic pad can charge the device.

The advantages of this type of charging include the fact that the absence of a cable eliminates all the risks associated with its use, be it loosening of the socket or electric shock due to poor insulation. Among the disadvantages, one can highlight the small range of action of such a device: the phone can be moved and rotated on the surface, but it cannot be torn off by more than a few millimeters.

Video: how to use wireless charging for iPhone

How to use a universal charger

"Frog" is a universal battery charger. With its help you can charge absolutely any battery. mobile phone or tablet.

Using a universal charger you can charge any smartphone battery

Every year, this charging method is used less and less due to the availability of older models of mobile phones, the increased reliability of new ones and the inconvenience of using the “Frog” itself.

The principle of operation of a universal charger is that the battery is charged directly from the network. To do this, you need to remove the battery from the phone, connect it correctly to the “Frog” antennae and connect the power by inserting the charger into the socket.

The difficulties are obvious. Open iPhone case or iPad is not so easy. Here you cannot do without special tools, the use of which at home creates a high risk of damaging the miniature circuits of the device, introducing dust into the case, or breaking it.

Video: how the Frog charger works

Alternative iPhone charging options

Technologies do not stand still, they develop, become more mobile and progressive. Chargers are not far behind: they promote the brand alternative sources energy. They all use the energy of wind, sun, movement and even fire to turn them into electricity and power our devices.

Wind generators - small devices, which, as the name suggests, are powered by the wind. The movement of air causes the blades to rotate, which through simple manipulations produces energy.

Wind generators are not the most popular type of charger, as there is always a risk of falling into a calm zone

Much more known method energy generation - solar panels. Scientists say the Sun will stop producing light and heat in about 4 to 6 billion years. This makes our main luminary a source of inexhaustible energy. And even though you won’t be able to charge the batteries at night, you can do this in abundance during a fine day.

Work in cloudy weather solar battery decreases

The next power source is a dynamo. What's more renewable than your own energy? The most inventive ones manage to attach a dynamo to the wheels of a bicycle, thereby freeing themselves from routine work for the sake of a fun ride.

The dynamo can also be used as a power source to charge your smartphone

These devices are on sale in almost all online stores specializing in technology and have USB ports specifically for charging phones.

How to speed up the charging process of your Apple device

Each of us at least once in our lives was in a hurry and at the same time had a dead phone. Now smartphones are not only a means of communication, but also an organizer, link With by email, notepad and so on. Therefore, there is a need to charge the phone as quickly as possible.

There are several ways to reduce battery charging time:

Smartphones from Apple are quite good and functional devices. But they have one drawback - low autonomy. When the charger is at hand, it can still be tolerated, but how to charge an iPhone without charging? Let's look at several ways.

According to statistics 15% IPhone owners use a gadget with broken screen. The situation is approximately the same with the charger. It often breaks, and a new one original charger you can't buy it in the store around the corner, unless, of course, it's service center Apple. Therefore, it is useful to know how to charge an iPhone when left without a charging device.

Here are three emergency options:

From USB port. This is a painfully banal method, but there are people who have never heard of this possibility.

If your iPhone won't charge from a wall outlet, most likely the problem lies with the adapter. Disconnect the cable from it and insert it into the USB port of your laptop or PC. Reverse side connect the cord to the phone. Turn on your computer and switch your smartphone to charging mode. As a rule, it takes 2-3 hours to fully recharge.

Alternative chargers. In case the standard charger runs out along with the cable, it’s useful to have an alternative on hand that doesn’t even need to be plugged into an outlet.

Present on the market various models, but the most effective are exercises that receive energy from the wind, sun and muscle strength:

Wind generator. Connect it to your iPhone and attach it to your bike or backpack while walking. In windy weather, the device can be fixed on a windowsill or window frame. Charging time from 0 to 100% - 5‒6 hours.
Solar battery. Essentially this is Power Bank, which is charged by solar energy. Leave it under the rays for several hours and then transfer the charge to your smartphone.
Dynamo machine. The most efficient device of this three, but requires human participation. Connect the charger to the iPhone and turn the special knob until you transfer enough energy to the gadget. According to the manufacturer, a full charge will take about 2-3 hours. Monotonous, but what can you do?!

All these devices are easy to find on Chinese Internet sites. Someone will say: “Trash.” Perhaps, but, as they say, if there is no fish, there is no cancer.

Use any other charger. IPhone manufacturers made sure that chargers from other manufacturers are not suitable for it, but in an emergency, all this is not important.

You can charge your iPhone with any charger, but there is a chance of damaging the phone. Therefore, use this method only in the most extreme cases. Here's what to do:

Find a charger from an old cell phone lying around.
Cut off the plug that was inserted into the phone.
Cut off part of the main winding from the cable.
Separate the wires and strip about half a centimeter of insulation.
Remove the battery from the iPhone.
Connect the wires to the battery contacts - plus to plus, minus to minus. For reliability, secure with electrical tape or tape.
Plug the charger into a power outlet.

Note: Do not touch the battery while charging as it becomes very hot. Do not leave her in this position for more than an hour. If you see the battery swelling or smoking, stop power supply immediately.

There are tricks that will revive your phone for a few minutes:

Take out the battery, cover the contacts with tape and return it back. In some cases, this is enough to make a short call.
Heat the metal plate and apply it to the battery. Increasing the temperature will increase the charge, which will last for a couple of minutes.
Pull out the power source and throw it hard onto something hard. You can tap it a little with a hammer. The main thing is to maintain the integrity of the battery and not damage the contacts. These measures should give a few milliamps of charge.

So now you know: there are ways to charge your iPhone without a charger. Some are safe, but others are best used only as a last resort.

The reality of modern times is that now there is not a single person without a mobile phone. This is normal, because all kinds of smartphones and all kinds of gadgets make life much easier. If earlier you could only make calls, now a mobile phone is just a computer that fits in your pocket. You can call, play, listen to music, go online or watch a movie, and all this is possible thanks to gadgets. But such potential of technology requires constant charging of devices, and the charger can fail at any time. What to do in this case?

For example, let's take one of the most popular brands mobile phones, iPhone. What to do if it is simply impossible to charge it using a charger.

Looking for an innovative solution

How to charge an iPhone 4 without charging if the charger suddenly breaks down or there is no electrified network nearby? This question torments many people today, because without electricity, a mobile phone, or any other gadget, is simply doomed to “starve” to death. Naturally, manufacturers are struggling to increase the energy capacity of the iPhone battery or change the design of the charger for charging even without electrical network, but so far this is only experimental.

There are quite a lot portable devices, which can help charge the phone, but in practice they cannot compare with conventional chargers, but when there are simply no options left, you have to look for an alternative. There are several solutions to the problem related to charging the phone and they really work.

Charging via USB

Manufacturers have only recently begun to make Alternative option charging your phone, and now when you buy an iPhone, not only a charger is available, but also USB cord, which can be a good replacement for a memory.

In case the main charger box fails, you can disable USB, and connect to any power source that has a corresponding input. It could be desktop computer, laptop, tablet or other devices. This method easily solves the problem with charging an iPhone, but we must not forget that the speed of energy supply is significantly reduced. If using a charger a smartphone could be charged in no more than 2–3 hours, then using USB this time doubles.

Charging with the case

As surprising as it may sound, it is now very easy to find a case that not only protects your phone from scratches and shocks, but also charges it. This charging option appeared literally a few years ago, but at the same time quickly gained its popularity. The whole point is that the case in which the iPhone is located is equipped with an additional battery with a capacity of 1500 to 3200 mAh, that is, it can become an excellent alternative charger. The bottom line is that the case does not actually charge the phone, but simply maintains energy in it, due to which the smartphone can be used much longer.

This method often saves you when you have to go out into the countryside or into a village where there are problems finding an outlet of suitable power. In addition to the function of charging the phone, the case is also shockproof, and simply has a beautiful and pleasant appearance. When using the case instead of a charger, the device displays the level of discharge of the secondary battery.

iQ Technologies

Among all the alternative ways to charge a mobile phone, the innovative iQ technology can be called the most popular on the market. The charging system is similar to when a phone recharged from the case, but here the speed of energy transfer is significantly increased. The iQ charger is best used only at home, because it is quite large, although it looks attractive from the outside.

This wireless way iPhone charging has one very interesting feature. The bottom line is that there is no need to constantly connect the cable, and thus you don’t have to worry about injuries to the charging pad. Many people have encountered a problem when the connector falls off after using the phone for a long time and this problem is inevitable. I have to constantly charge my iPhone due to heavy use, but wireless system iQ easily solves this problem and prevents damage to the charger input.

On modern market such wireless charging platforms are presented in different forms, colors and materials, so there will be no problems with the choice. In addition, it is also important to consider the ease of use of the charging platform.

The perfect way to charge your mobile phone

Using the method using iQ charging is, of course, convenient, but still the plastic quite spoils the appearance of the phone. Even so, the method became the most popular, so manufacturers began not only to work on iPhone wireless charging, but also to think about appearance plates. Today we can say for sure that iQi Mobile has no worthy analogues.

This innovative way to charge your phone combines a silicone case that contains charging plastic. If its thickness used to confuse device owners, now it is about 1.5 mm, which is almost invisible under the silicone case. In addition, if you use the wireless charging method, it remains possible to simultaneously use the charger. Even so, an alternative charger has its advantages and disadvantages.

Advantages:

comfortable use;
no need to use a mechanical connection;
safe operation at high humidity.

Flaws:

You cannot use the phone while the battery is charging;
the weight and thickness of the phone increases;
high cost of a wireless charger.

Conclusion

Anyone can charge their phone from a computer with via USB, but this is not always possible. Sometimes, when you go out into nature or to another place where there is no electricity, the phone just doomed to completely discharge, and in our time - this is destructive for a person, because the connection with outside world. Alternative methods Chargers can be an excellent solution to problems in this case. Many innovative technologies help charge your phone by converting thermal, kinetic and mechanical energy into charge for your phone and even though a large number of disadvantages, sometimes you simply cannot do without such options.

The weakest link in iPhone already for many years the battery has been considered. Under average load, it can keep the device offline for no more than a day, after which the gadget will be completely discharged. You may not be familiar with this problem only if you use it to make 2-3 calls a day with an average duration of 3-4 minutes.

Of course, Apple's proprietary charger ensures that the battery returns to full capacity within 1 hour, but if you go on a long trip, finding an outlet in time is a real challenge.

In order to renew the battery charge, you can use various energy sources: from computer USB ports to special cases. The choice depends on your preferences and available means.

How to charge iPhone without charging while on the road?

It is worth noting in advance that using a non-original charger or one not approved by the company Apple ways charging, you risk damaging your smartphone or even getting injured.

Charging iPhone via USB connector of computer or car radio

To do this, you will need a standard USB cable for your phone (30-pin for older models and Lightning for all models starting with iPhone 5). Using it, you can charge your smartphone from any computer, laptop or tablet that has a USB connector. You only need to connect the cable to your mobile phone and computer, after which charging will begin almost immediately. In addition, if your car has a car radio with a USB connector for connecting flash drives, you can use it to recharge the device.

How to charge an iPhone without charging using iQi Mobile?

iQi Mobile is small (thinner and smaller plastic card) external antenna, designed to receive electricity from a Qi wireless charger. It is attached from the outside back cover smartphone using adhesive tape, and then connect it to the Lightning connector. After this, the device is put on Silicone Case or an overlay that hides this “design”.

To start charging, just place the iPhone with the back panel on the surface. special stand, supporting the Qi standard.

Charging an iPhone using an external battery

You can use any manufacturer if you purchase a universal external battery. It is equipped with a USB port for connecting a charging cable and will allow you to “resurrect” your smartphone as quickly as possible. In addition, there are special cases for the iPhone with a built-in battery (such as the Juice Tank Helium). This accessory It is enough to put it on a smartphone so that it can extend the “life” of the device by almost 2 times.

The downside of most smartphones is that they run out of battery quickly. Unfortunately, Apple devices are no exception, so many users naturally have a question: how to charge an iPhone without charging. Is this possible in principle? Unlikely, but you can put in a little effort and significantly extend its battery life by using third party devices for charging.

We'll tell you how to make your gadget work longer and look at the process of repairing a broken charger for Apple phones.

Many smartphone owners are concerned about the problem that they quickly discharge

How to charge an iPhone without using a special device?

There are several ways:

You can make up for the lack of energy using a USB cable - just connect your device to your computer, laptop, tablet and any other energy source through it.

Charging via USB

Using an external battery or powerbank - such devices can recharge your iPhone several times to a maximum of one cycle of its own energy reserve. External batteries are also charged via the network and are an excellent option for those who need to frequently recharge their gadget. They take up little space and are produced by many manufacturers - be careful when choosing, do not save too much on them.

Cases with built-in batteries. If you don't like to carry separate device, as in the previous case, you can buy a case that can charge your iPhone. It also needs to be “filled” with energy first, and when you are on the road, the case can provide several days of operation for the gadget. Note that this result, of course, depends on the battery capacity of the device itself.

Case with built-in battery

And, of course, to many such a device will even seem the best way out, how external battery, since the case additionally performs another main function - it protects the device from damage and scratches.

Solar panels. They are somewhat reminiscent of a power bank, but they do not need to be charged using electricity. All you need to do is connect your phone to the battery, place it in a sunny place and wait a bit. This is very convenient, especially in summer and spring, when the days are longer and the sun shines stronger. In addition, this option the better that you do not need to pre-charge the battery - solar energy will be an excellent solution when you cannot connect to other sources.

Solar panels

Fire-powered devices. Yes, you can charge your battery using real fire. For this, there are special blocks that convert heat into electrical energy. True, they are not as effective as other means, but in extreme cases they will save the phone from completely turning off.

Fire-powered devices

In the same way, there are wind generator devices that can restore charge using the wind. If there is no wind, you can compensate for it by running, or use the device while walking or cycling. True, for fully charged it will take 5–6 hours.

Wind generator

It is worth noting that in the future, chargers in the form of a power supply with a cable may disappear, because plates for wireless power supply will become more common. Why? This way you can better protect the charging connector, which quickly deteriorates due to constant use of the cable.

What to do if you don’t have all these funds?

In this case, use the following recommendations:

If you're near a shopping center, try looking for chargers in the rest areas or stores there. In addition, mobile operator centers should have network cables for most brands of phones by default.
You can go to a service center and ask to charge your phone - even if they ask for money for the service, it will not cost much.
There are special charging terminals - they are installed in the same entertainment complexes and are also inexpensive.
When charging your iPhone, turn on airplane mode - with this method of operation, all communication modules that consume the most battery power are deactivated, and you will replenish your energy much faster.

How to fix iPhone charger?

If your iPhone charger is broken and you are confident in your abilities and capabilities, try to fix it yourself. To do this, do the following:

Trim the plastic shell on the end of the charger so as not to touch its insides. We are talking about the thicker end of the charger.
Cut the cable where it breaks.
Remove the protective winding to have access to the 3 thin wires, which should also be visible from the plug.
Remove the insulation from all wires, but so as not to damage the metal core.
Connect all the wires together by color and wrap them with electrical tape.
The electrical tape must be applied so that there are no bare wires left.
If desired, buy heat shrink and put it on the part of the wires that you repaired.

After all of the above, you will know how to charge an iPhone without the main device. We recommend that you purchase one of the recharging devices to be able to always stay connected. And of course you can always try to fix it network device on your own - as you can see, there is nothing too complicated about it.

Today it is impossible to imagine a modern person without a mobile phone. However, it is impossible to imagine an electronic gadget without the accompanying full process of operation. additional devices, the presence of which is mandatory. For example, a failed charger will certainly doom the “dependent” device to “energy death”. However, the question of how to charge an iPhone without charging, given the great popularity of the “yield” Apple brand, requires special coverage. Several of the most original technological innovations will be presented to your attention, allowing you to “pump up” Californian gadgets with the much-needed power of electricity for their batteries, of course, without the “participation” of the standard charger provided.

In search of promising technologies

First of all, the question requires some specification. After all, each of us knows that without the influence of a certain type of energy, none of the known inventions of “human genius” will be able to function. Therefore, the question of how to charge an iPhone without charging does not yet have a complete answer. Of course, some attempts by developers to change the principle of “life support” of the phone were successful. It goes without saying that the standard memory will undergo dramatic changes in the near future. The problem of “expedient universality” already has several fundamentally different solutions. However, today it is not yet possible to “globally decouple” mobile units from commonly used power outlets. However, how to charge an iPhone or other “brainchild” of the electronics industry when there is no access to the “benefits of civilization” is already a realistic reality. But the low efficiency (efficiency) of the developed and, by the way, mass-produced devices and at the same time the lack of thorough thought out of the feeding “mechanism” certain power charge is somewhat removed from being a full-fledged alternative to a 220 W source or other rating of the generally accepted standard for centralized electrification. As a result, we are seeing an ever-increasing need for and genuine interest from manufacturers... It is these facts that are pushing developers to find the most appropriate technological solutions.

Review of the most effective methods of “energy refueling” without using a standard power supply

Method No. 1

Perhaps we’ll start with the most basic, but not always affordable option power supply of a mobile device. Perhaps you don't know how to charge your iPhone from your computer. So let's take a look this method charging, which, as you understand, implies the use of a laptop, tablet or device equipped with If the operating level of the battery has become critical, and your device is “tired” of warning about it - the screen blinked and went out, you need to connect it to any available device, having the necessary port. Thanks to this, you will be able to answer the question of how to charge an iPhone without charging with a practical action.

Not demanding method No. 2

Today you can buy a charging case. That is, the design feature of such a device will be the presence of a built-in battery, the capacity of which varies from 1500 to 3200 mAh. This allows you to use the phone for quite a long time without recharging. Convenient case not only ergonomic and aesthetically attractive. The in-demand device will help to effectively solve the problem of how to charge an iPhone without charging, and will also provide shockproof properties to the device. Moreover, protection from mechanical damage the back of the iPhone is guaranteed in any design of the charging case. The indicator on the front panel of the device shows the battery level, thanks to which the user can always visually determine the level of performance of the auxiliary battery.

Not quite an easy way #3

Of course, iQ technology - a definitely innovative option for wireless charging - helps to effectively “refill” the battery capacity without the difficult moment caused by connecting a 30-pin connector to the connector. The question of how to charge an iPhone without charging will no longer express unrealistic hopes. At the same time, the comfortable method greatly facilitates many operational tasks, and in particular, it is the most gentle way to restore the electrical potential of the battery. Since wear and damage to the contact pad of the iPhone is a natural inevitability due to intensive use of the phone, as a result of which the device often has to be recharged. Attractive module design that serves as an intermediary element between charging station and the battery of a mobile device, mounted on back gadget, and the installation process is not complicated and does not require special tools or installation skills. On the market, these are products that are presented in a variety of designs. The color, texture and material of the “intermediate device” are available to the user to suit almost any preference. The only disadvantage of such a memory can be considered the necessarily accompanying process of “upgrading” the device, which increases the “waist” of the smartphone by several millimeters. However, sometimes the question of how to charge an iPhone is resolved not only in this way...

Improved method No. 4

Today, the iQi Mobile project presents a slightly improved version of the new power standard. Despite the “freshness of the idea,” an ever-increasing trend of consumer demand is visible in the market for goods for mobile devices. The qualitatively modified charger, which has received wide recognition in user circles, allows for wireless “filling” of electricity into the phone’s battery. The main advantage of the new product is a critically reduced induction plate (receiver). The problem of how to charge an iPhone without charging and without “disfiguring” the design is becoming completely solvable. After all, the thickness of the additionally installed element is only 0.5-1.5 mm and is practically invisible under a thin layer of silicone frame. This fact iQi Mobile stands out from previously implemented wireless power standards. The connection condition can be considered important: a flexible connection to the Lightning port does not in any way complicate the user’s subsequent actions, primarily related to the use of the 30-pin Iphone port. Agree, this greatly simplifies many aspects of mandatory access to the sometimes extremely necessary system connector of a mobile unit.

Several arguments in favor of wireless storage

No mechanical connection torque (direct contact).
Possibility of safe operation in unfavorable environments (moisture, dampness).
Ease of use (mostly).

A little about the disadvantages

Cost, size and weight are increasing.
Time parameter of useful action electrical energy significantly exceeds standard option(taking into account the efficiency of the original memory).
It is not possible to use the phone while the battery is charging.

Summing up, or Energy prospects for iPhone

You know how to charge your device from a computer. But what do you do when you're camping or find yourself in a situation where there are no standard power sources available? Today, there are devices on the market that can charge mobile devices using alternative methods receiving electricity. These are original technological solutions in the form of converting devices that convert mechanical, thermal, kinetic, magnetic and other types of energy into the voltage and current required by your device. Of course, there are many more disadvantages and shortcomings in the available devices than we would like. Price, weight, dimensions and other disadvantages hinder the path to achieving absolute perfection. But time passes and technology develops...

Each of us has at least once found ourselves in a situation where the phone is discharged at the most inopportune moment, and there is no charger at hand. This is especially annoying when at this time you need to make a very important call or urgently use your phone data. This article will tell you how to avoid awkward situations and how to find a way out of them when it seems that there is no way out.

How to charge an iPhone without charging?

If you don’t find a charger in your bag, and you need a smartphone right away, then don’t give up; nowadays there are many new technological devices that can save you in this difficult moment.

The simplest and most obvious way at first glance is to use a laptop or PC as a power source, that is, using a USB port. To charge your phone, you just need to have a charging cord with you, and instead of the power supply, use your PC or laptop, connecting one end of the cord to the iPhone and the other to the computer. Of course, the charge speed will be a little slower, but you are already saved, all that remains is to wait a little time.

Charging using third-party power sources

There are many accessories on the electronic goods market that can be used to successfully recharge your battery. This could be a PowerBank from various manufacturers and a variety of portable storage devices. The system of their operation is extremely clear - you connect the gadget to your phone and enjoy the result.

1 With the help of a portable battery or as it is otherwise called Power Bank, you don’t have to worry about how much interest is on your phone, because you carry a “second battery” with you. On this moment choice and price policy There are a lot of such devices, and you can find exactly the one that suits you in terms of color, price and characteristics.

2 Portable batteries powered by nature. The devices that appeared on the shelves not long ago have already won the hearts of fans. active rest. If your phone is dead and you are high in the mountains, on a sunny beach, or perhaps just in the country, you will find power sources that will help charge your smartphone using fire, wind or solar energy. Each of these methods is actually very simple and easy to use.

How can I charge without a cord?

To charge your essential gadget without using a cord, there are several innovative types of energy sources. Especially for the iPhone 6 and other models, we have developed a very stylish and convenient iQi Mobile charger, both for working at your desk and at home, thanks to which you can forget about a bunch of wires. You just need to place it once on a horizontal surface convenient for you and your phone will always be at hand. This type of charger is suitable for the following models: iPhone 5, iPhone 5s, 5c, 6, 6+. Unfortunately, iPhone 4 does not support this type of device.

You can also charge your iPhone using a special Smart case Battery Case. He approaches iPhone models 6, 6+. One part of this case is flexible enough to easily insert or remove an iPhone. While charging in such a case, the navigation panel of the device will display 2 stages of charging - the built-in battery and the case. Using this accessory, it becomes possible to talk on a cellular connection for about 25 hours or surf the Internet for about 18 hours. Maximum convenience when turned on, they make this accessory top-of-the-line, because in order for it to work you just need to press the power button and you’re done.

Charging in public places without a charger

It happens that you went shopping at the mall or decided to have a cup of coffee with friends, and your smartphone suddenly shows an ominous red battery. Even if you don’t have a charger at hand, there is a way out. In addition to various accessories, there are very convenient and effective ways how to charge an iphone or other smartphone if you are in public place. We can offer you some of them:

1 Special terminals for charging devices. These are special cells, inside which there are several types charging cords, you can leave your phone there for a while and come back for it whenever you want, and it will already be waiting for you with full battery and ready for further use. Such cases are just gaining popularity, so you can find them inside airport buildings, railway stations, large shopping centers and cafes.

2 If you are in a cafe, then most likely you can ask the bartender behind the counter or the waiter to put the phone on charge for a while. Almost every cafe has such a completely free service. 3 Walking around Shopping center you can go to your phone's brand store or any other electronics store and ask them to put your phone on a little charge. You are unlikely to be refused, since such stores have chargers for almost any phone model. 4 If you are driving, don’t be upset; when you stop at a gas station, while your car is being refueled, you can ask for a little recharge of your phone, and at the same time drink a cup of tea or coffee. This service is also free.

False methods or what is better not to do

The Internet is filled with many videos on how to charge your phone using fruits such as apples and lemons. In fact, this will not do any good and may even harm your phone, and your charging port may break or burn along with your phone.

There is also a method on the Internet that describes in detail how to strip the wires on a broken charger or how to charge using wires. We do not recommend performing such operations without proper repair experience and skills in working with electronics.

PS

You can switch your phone to Airplane or Airplane mode. In this mode, the phone will discharge much more slowly.
If it is not possible to use the first option, then simply turn off GPS and other additional functions. Also lower the screen brightness.

If you find an error, please highlight a piece of text and click Ctrl+Enter.

Today it is impossible to imagine a modern person without a mobile phone. However, it is impossible to imagine an electronic gadget without additional devices accompanying the full process of operation, the presence of which is a mandatory necessity. For example, a failed charger will certainly doom the “dependent” device to “energy death”. However, the question of how to charge an iPhone without charging, given the great popularity of the “yield” Apple brand, requires special coverage. Several of the most original technological innovations will be presented to your attention, allowing you to “pump up” Californian gadgets with the much-needed power of electricity in their batteries, of course, without the “participation” of the standard charger provided.

In search of promising technologies

First of all, the question requires some specification. After all, each of us knows that without the influence of a certain type of energy, none of the known inventions of “human genius” will be able to function. Therefore, the question of how to charge an iPhone without charging does not yet have a complete answer. Of course, some attempts by developers to change the principle of “life support” of the phone were successful. It goes without saying that the standard memory will undergo dramatic changes in the near future. The problem of “expedient universality” already has several fundamentally different solutions. However, today it is not yet possible to “globally decouple” mobile units from commonly used power outlets. However, how to charge an iPhone or other “brainchild” of the electronics industry when there is no access to the “benefits of civilization” is already a realistic reality. But the low efficiency (efficiency) of the developed and, by the way, mass-produced devices and at the same time the not thoroughly thought out “mechanism” for supplying a certain charge power somewhat distances it from being a full-fledged alternative to a 220 W source or another rating of the generally accepted standard of centralized electrification. As a result, we are seeing an ever-increasing need for and genuine interest from manufacturers... It is these facts that are pushing developers to find the most appropriate technological solutions.

Review of the most effective methods of “energy refueling” without using a standard power supply

Method No. 1

Perhaps, let's start with the most basic, but not always accessible, option for powering a mobile device. Perhaps you don't know how to charge your iPhone from your computer. Therefore, let's look at this charging method, which, as you understand, involves using a laptop, tablet or device equipped with If the operating level of the battery has become critical, and your device is “tired” of warning about it - the screen blinked and went out, you need to connect it to any available device that has the required port. Thanks to this, you will be able to answer the question of how to charge an iPhone without charging with a practical action.

Not demanding method No. 2

Today you can buy a charging case. That is, the design feature of such a device will be the presence of a built-in battery, the capacity of which varies from 1500 to 3200 mAh. This allows you to use the phone for quite a long time without recharging. A convenient case is not only ergonomic and aesthetically attractive. The in-demand device will help to effectively solve the problem of how to charge an iPhone without charging, and will also provide shockproof properties to the device. Moreover, protection against mechanical damage to the back of the iPhone is guaranteed in any version of the charging case. The indicator on the front panel of the device shows the battery level, thanks to which the user can always visually determine the level of performance of the auxiliary battery.

Not quite an easy way #3

Of course, iQ technology - a definitely innovative option for wireless charging - helps to effectively “refill” the battery capacity without the difficult moment caused by connecting a 30-pin connector to the connector. The question of how to charge an iPhone without charging will no longer express unrealistic hopes. At the same time, the comfortable method greatly facilitates many operational tasks, and in particular, it is the most gentle way to restore the electrical potential of the battery. Since wear and damage to the contact pad of the iPhone is a natural inevitability due to intensive use of the phone, as a result of which the device often has to be recharged. The attractive design of the module, which is an intermediary element between the charging station and the battery of the mobile device, is mounted on the back of the gadget, and the installation process is not complicated and does not require special tools or installation skills. On the market, these are products that are presented in a variety of designs. The color, texture and material of the “intermediate device” are available to the user to suit almost any preference. The only disadvantage of such a memory can be considered the necessarily accompanying process of “upgrading” the device, which increases the “waist” of the smartphone by several millimeters. However, sometimes the question of how to charge an iPhone is resolved not only in this way...

Improved method No. 4

Today, the iQi Mobile project presents a slightly improved version of the new power standard. Despite the “freshness of the idea,” the market for goods for mobile devices There is an increasing trend in consumer demand. The qualitatively modified charger, which has received wide recognition in user circles, allows for wireless “filling” of electricity into the phone’s battery. The main advantage of the new product is a critically reduced induction plate (receiver). The problem of how to charge an iPhone without charging and without “disfiguring” the design is becoming completely solvable. After all, the thickness of the additionally installed element is only 0.5-1.5 mm and is practically invisible under a thin layer of silicone frame. This fact sets iQi Mobile apart from previously implemented wireless power standards. The connection condition can be considered important: a flexible connection to the Lightning port does not in any way complicate the user’s subsequent actions, primarily related to the use of the 30-pin Iphone port. Agree, this greatly simplifies many aspects of mandatory access to the sometimes extremely necessary system connector of a mobile unit.

Several arguments in favor of wireless storage

No mechanical connection torque (direct contact).
Possibility of safe operation in unfavorable environments (moisture, dampness).
Ease of use (mostly).

A little about the disadvantages

Cost, size and weight are increasing.
The time parameter of the useful action of electrical energy significantly exceeds the standard version (taking into account the efficiency of the original charger).
It is not possible to use the phone while the battery is charging.

Summing up, or Energy prospects for iPhone

You know how to charge your device from a computer. But what do you do when you're camping or find yourself in a situation where there are no standard power sources available? Today, there are devices on the market that can charge mobile devices using alternative methods of generating electricity. These are original technological solutions in the form of converting devices that convert mechanical, thermal, kinetic, magnetic and other types of energy into the voltage and current required by your device. Of course, there are many more disadvantages and shortcomings in the available devices than we would like. Price, weight, dimensions and other disadvantages hinder the path to achieving absolute perfection. But time passes and technology develops...