Installing zyxel keenetic lite 2. Software configuration of the router. Via mobile application

Second generation of routers ZyXEL Keenetic Lite differs from the previous one in small fixes and improvements that affect stable operation and ease of use network equipment. The configuration of such routers is still carried out through a proprietary Internet center in one of two modes. Next, we invite you to read the guide on this topic in detail.

Most often during ZyXEL works Keenetic Lite 2 is used not only wired connection, but also a point Wi-Fi access. In this case, even at the stage of choosing a location for installing equipment, one should take into account the fact that obstacles in the form of thick walls and working electrical appliances often provoke deterioration wireless signal.

Now that the router is in place, it's time to connect it to a power source and insert the necessary cables into the connectors located on the rear panel. Yellow LAN is selected where it is inserted network cable from the computer, and the WAN port is indicated in blue and a wire from the provider is connected there.

The last stage preliminary actions there will be editing Windows settings. The main thing here is to make sure that the IP and DNS protocols are obtained automatically, since they separate setting will be carried out in the web interface and may provoke the appearance of certain authentication conflicts. Read the instructions provided in our other article at the link below to understand this issue.

Setting up the ZyXEL Keenetic Lite 2 router

We have already said earlier that the procedure for setting up the operation of the device is carried out through a proprietary Internet center, also known as a web interface. Therefore, you first log into this firmware via a browser:

Next, you successfully log into the Internet center and the developers offer two configuration options to choose from. Quick method through the built-in Wizard allows you to set only the main points of the wired network; security rules and activation of the access point will still have to be done manually. However, let us look at each method and individual points in order, and you decide what would be the most optimal solution.

Quick setup

In the previous paragraph, we focused on which parameters are edited in quick configuration mode. The whole procedure looks like this:

There is no need for further adjustment of the router if, except wired connection you won't use anything else. As for activating a wireless access point or editing security rules, this is done through the firmware.

Manual configuration in the web interface

First of all, the WAN connection is adjusted when you bypass the Wizard and go straight to the web interface. Let's look at each action in detail:

This is the procedure in the category "Internet" completed. Finally, I would like to note only "DyDNS", through which the service is connected dynamic DNS. This is required only for owners of local servers.

Wi-Fi Configuration

We smoothly move to the section on working with wireless point access. Since its configuration was not done through the built-in Wizard, the instructions below will be useful to all users who want to use Wi-Fi technology:

Only a few steps were required to ensure correct operation wireless internet. This procedure is quite easy and can be done even by inexperienced user.

Home group

In the previous part of the instructions you may have noticed a mention home network. This technology unites all connected devices into one group, which allows you to transfer files to each other and have access to shared directories. Special mention should be made correct configuration home network.

Safety

An important point is the actions with the router’s security policies. For the router in question, there are two rules that I would like to dwell on and explain in more detail.

We will not consider the DNS function from Yandex separately, since we mentioned it in the section on quick setup. Let us only note that at the moment the tool does not always work stably, and sometimes glitches occur.

Final stage

Before leaving the Internet center, you need to spend time setting up the system; this will be the final stage of the configuration.

After completing the configuration, it will be enough to reboot the device for all changes to take effect, and then proceed directly to accessing the Internet. By adhering to the above recommendations, even a beginner will be able to get things working ZyXEL router Keenetic Lite 2.

Hello dear readers of our site. In this article we will talk about setting up a Zyxel router keenetic lite ii(2). This model The router differs from its predecessor Zyxel keenetic lite in that it has become more productive and maintains stable speeds on any type of connection. The main difference is appearance and adding a second antenna, which should increase the transmission range WiFi signal. The settings interface has also changed, which made setting up the Zuksel 2 router more difficult for the average user. So in this article we will look at the basic settings of the Zyxel keenetic lite II (2) router.

ii (2) to the computer.

U this router not only a Russified setup interface, but also, as we can see from the picture, a fully translated back panel. Thus making connecting the router to the computer even easier than before. We follow the points:

We connect the power supply to the router and insert it into the outlet (220V). After that, click on the button “ Nutrition" By connecting power to the router right away, it will be easier for us to monitor in the future.
We connect the Internet cable of your provider to the special “Internet” port marked blue on the router. After this, if there is a signal in the provider’s wire, the indicator with the number “0” lights up. This will mean that the connection was successful. If the “0” indicator does not light up, this means that your provider’s wire in the apartment or in the entrance is either damaged, or the provider has stopped sending a signal.
Take the short wire included in the kit. We connect one end of it to any of the “Home Network” ports; I advise you to select the 1st one. And we connect the other end of the wire to the network card of the computer. After this, the indicator number “1” should light up and blink if you connected the wire to port “1”. If the indicator does not light up there are several problems. The most common problem this is a faulty network card or its incorrect connection. It also happens that the wire included in the kit is damaged, but this is very rare.

Connecting Zyxel keenetic liteii (2) to laptop viaWiFi.

I’ll say right away that I don’t recommend it. initial setup router via WiFi. To avoid unexpected problems. But if you decide, then you just need to connect to the Wi-Fi router. To do this, first check whether WiFi is turned on on the router; the Wi-Fi indicator should be on, it should be located immediately after the number “4”. If it is not lit, then simply press the button on the top cover of the router, it turns it on and off.

Checking network card settings

It’s best to immediately make sure that the settings network card are displayed correctly.

On Windows XP:

Go to “Start”, then find “Control Panel” and click on it. In the window that opens, click on the link “Switch to category view”; if there is no such inscription, then you have already switched. We look for the icon that says “Network connection” and double-click on it.

Then click right key mouse on the “Connect via local network" and select "Properties" from the drop-down menu. In the window that appears, select “Internet Protocols TCP/IP” from the list with check marks and click the “Properties” button. Then we check that the dots are opposite the words “Obtaining an IP address automatically” and “Obtaining a DNS server address automatically.”

On Windows 7, 8, 8.1:

In the lower right corner, you should have a "Network" icon. Right-click on the icon and select “Network and Sharing Center.”

Then we carry out the same actions as shown in the figure below.

Resetting the Zyxel keenetic lite router settings to standard

Let's immediately consider the case when this may be necessary. Basically, resetting the settings is required when the router password is forgotten, this is the only option. Also, when you configure the router incorrectly and don’t know how to fix the error, resetting the settings to standard will help.

Resetting the settings is very simple. Take any thin object (needle, match, pen paste, etc.). And press the recessed button above the “Reset” inscription, hold the button pressed for 30-40 seconds, then wait for the router to reboot for a couple of minutes. That's it, the reset is complete.

Important: During a reset, the router must be connected to the network and turned on.

Login to the Zyxel keenetic liteii setup interface (2)

If you connected the router correctly, and checked the network card settings, and found out that the router is connected normally. After that, opening any browser (Opera, Yandex, Google Chrome), when you try to open any page, you should automatically see the router’s welcome page. If this does not happen then just dial address bar 192.168.1.1. The welcome page will offer you the choice to use " quick setup router" or go directly to the router interface. I always suggest going straight to configuration in the web configurator. To do this, click on the “Web Configurator” button.

Changing the password for the zyxel keenetic lite ii router (2)

After this, a window will open in front of you where the router will ask you to set the administrator password. Fill in two fields " New Password administrator" and "Enter the password again" we come up with a password and enter it. And click the “Apply” button.

After clicking the button, the router will ask you to log in. Enter the “Username” - admin, and the password is the one you set. Click the “OK” button

After this, the first page of the router interface will open in front of you “ System monitoring» .

SettingsWiFi onZyxel keenetic lite ii (2)

Let's go straight to Wi-Fi settings networks. To do this, click on the Wi-Fi icon at the bottom of the page.

Here we must fill in the fields:

« Network name (SSID)» enter the name of your network. This is the network name that will be displayed when connecting to Wi-Fi.
In field " Network protection"Select WPA2-PSK from the list. This is the most secure type of signal encryption.
In field " Network key» enter any password. Which must consist of eight characters and numbers.
In field Channel select Auto. If problems arise with WiFi operation then select a specific channel.
It is better to leave the remaining fields unchanged.
After filling out all the fields, click on the “ Apply».

Setting up the Internet, various types of connections.

This router supports all known connection types. In this section we will analyze them all in more detail. First, let's go to the Internet settings section by clicking on the corresponding icon at the bottom of our interface.

First, let's look at the three main and popular types of Internet connection. These are types of connections that require authorization via a login and password. To do this, go to the “PPPoE/VPN” tab and click on the “Add connection” button

Setting up a PPPoE connection

Probably the most popular connection type. For this you need to fill in certain fields:

Type (protocol)— select PPPoE from the list.
Connection via Broadband connection (ISP).
Username– enter your login from the agreement with the provider, if not, check with the provider’s support.
Password— your password from the agreement with the provider.
Configuring IP settings –
Save the settings by clicking on the " Apply».

Setting up a PPTP connection

Type (protocol)— select PPTP from the list.
Connection via— select our interface. The default is Broadband connection (ISP).
Server address enter the server address specified in the contract. This is also what some providers call it VPN server address.
Username
Password
Configuring IP settings select “Automatic” from the list.
Authentication Method you need to check with your provider. But first put “ Auto»
Service Name, Hub Name, Description– filled out only if there is a requirement from the provider.
Apply.

Setting up L2tp connection

Type (protocol)— select L2tp from the list.
Connection via— select our interface. The default is Broadband connection (ISP).
« Server address» Enter the server address specified in the contract. This is also what some providers call it VPN server address.
Username This is your login from the agreement with the provider.
Password is also in the agreement with the provider. If not, check with your provider's support team.
Configuring IP settings select “Automatic” from the list.
Authentication Method you need to check with your provider. But first put “ Auto»
Service Name, Hub Name, Description– filled out only if there is a requirement from the provider.
After filling in all fields, click the button Apply.

Dynamic connection type, automatically obtaining an IP address.

This type of connection does not require settings; it is in the router settings by default. But for those who want to reconfigure the router from a different type of connection. To do this, go to the section Internet, and in paragraph “ Connections", click on the Broadband connection (ISP) link. Here you need to check that the fields " Configuring IP settings» has been selected Automatic. And in the field MTU size enter 1400.

Changing firmware on Zyxel keenetic lite II

To change the firmware, you first need to download it to your computer. This can be done on the page https://zyxel.ru/keenetic-lite-2. On this page, go to the "Support" section.

Then in the table " Firmware» choose the most current version firmware, and download the ziparchive. Or unpack it in a place convenient for you.

Then go to the router interface, select the “ System", in it select the item " Configuration" In the table with the list of “Files,” select the file named “firmware” and click on it.

The file management window will open, in it click on the “Select file” button. We find our unpacked file and select it. After that, click on the “Replace” button. And we wait for now new firmware will be established.

A few minutes will pass, then enter the router configuration interface again. There will be new firmware.

Opening ports on the Zyxel Keenetic Lite II router

Opening ports on the router is required to special programs, if you use the distribution in " µTorrent»or use DC++ professionally. But the topic is large and if it were covered in full it would be a separate article. Which I will write soon, of course, but for now a video on how to open a port on the Zyxel Keenetic Lite II router:

Blocking Wifi network users by MAC address

Required if someone abuses your kindness. View detailed video. Around 12.40 starts what we need

Zyxel is a world-famous brand under which network and periphery equipment top class, proven by time and millions of users. The quality of workmanship and ease of use will allow any novice user to configure their Zyxel router in short term and work online.

Turning on the router for the first time

Setting up the ZYXEL KEENETIC LITE 2 router for dummies begins with the user having to connect all the wires and the device itself in the correct sequence. To do this, the user must first connect the power supply to the mains. Next, you need to connect the Internet cable to the router. After which the user must connect the second cable included in the kit to the computer.

If everything is done correctly, a signal in the form of a round icon with a partially crossed out circle should light up on the case. It means that the device is powered from the mains.

The second signal in the form of a ball with a net should also light up.

This signal means that the user can begin setting up the router.

Video: Setting up the ZYXEL KEENETIC LITE 2 router

Hardware connection

There are many videos on the Internet “how to configure the ZYXEL KEENETIC LITE 2 router.” But you can do everything yourself and without outside help. Connecting the network kit occurs in several stages:

checking the operation of the network card on the computer;
connecting the router to an Internet cable and computer;
setting up a local network and Internet connection.

Checking the functionality of the network card when connecting a router is as follows:

go to “start” and select the “control panel” tab;
select the “Network and Sharing Center” shortcut shared access"or the "Network and Internet" and "Network and Sharing Center" tab;

open the option “change adapter settings”;

right-click on the “Local Area Connection” shortcut;
if the connection is not connected, then connect;
in the connection properties, select the “Protocol…” line and click on the “properties” option;

in the window that appears, check the boxes automatic settings IP and DNS addresses;
repeat the last operation with “Protocol...4”.

If the user has done everything correctly, a monitor icon with a yellow triangle and exclamation mark. This means that the computer and router are connected to the network and you can proceed to the next step of setting up the router to create an Internet connection.

Changing the factory password

After the user has made a hardware connection, it is necessary to begin directly setting up the router. First, go to the Internet browser at 192.168.1.1. In the login column we type “admin”, and in the password column – 1234.

The system prompts you to change your password at the very beginning. The user should not abandon this procedure; he must immediately change it to a more complex one in order to avoid logging into the domain of third-party users in the future.

After logging into the domain, an updated window will appear in which you must enter new login and password data using numbers, letters different sizes and various symbols. Next, select the “apply” option. The system will save the new domain data.

Firmware update

If during the setup process the router does not start to function in full force and in the proper order, that is, there are two options for resolving the problem:

reset settings to factory settings;
firmware update.

First option involves completely resetting all set parameters of the router and is used only when the order is disrupted full customization from the moment the device is connected until the network connection is created. To do this, you need to press the emergency reset button on the back of the router panel, after which the device will automatically reset all set parameters.

Second option involves updating the version software. This is due to the fact that outdated versions Drivers are not always compatible with the version of the operating system being used, which can lead to network equipment malfunctioning and a lack of Internet connection.

To solve this problem necessary:

To fully configure the Zixel router, there is a web interface on the home page - 192.168.1.1. Here you can do the following:

change the connection mode between the router and computer to increase the transfer speed;
tune additional network or change her privacy settings;
set up a new connection or change the connection technology from “pppoe” to “l2tp”;
check the number of connected devices and limit access;
create a local network between computers.

Setting up and connecting to the Internet

If you were unable to connect to the Internet during the automatic setup process, you must manually check and set all connection parameters for normal operation of the network equipment. In this case, the question arises of how to reset the settings. The user must press the button on the back of the router to reset the configuration of all settings. Thus, the system will completely erase all configured settings. There is a video on the Internet “instructions for setting up ZYXEL KEENETIC LITE 2.” But such videos do not show all the nuances of the setup, which subsequently leads to a failure of the Internet connection. Most often, settings errors occur at the introduction stage on the router’s home page. If the user cannot configure pppoe independently in the future, then proceed as follows:

Thus, the user will create a new connection with the router settings for connecting to the Internet.

Setting up for Rostelecom and Dom ru

The leaders in the Internet services market are two companies - Domru and Rostelecom. They use approximately similar connection technologies (pppoe), so the process of setting up equipment and connecting to the network is similar. The operator TTK-Chita, for example, uses the same technology. Setting up ZYXEL KEENETIC LITE 2 for MTS, Domru and Rostelecom will occur as follows:

checking the electrical connection;
checking the connections of cables and wires to devices;
checking the operation of the computer's network card;
automatic network setup using web interface prompts home page router (192.168.1.1).

This sequence of actions can be completed by both experienced and novice users.

Setting up for Beeline

Beeline uses L2TP connection technology, which will require additional settings in the following way:

If all actions are carried out strictly in accordance with the above order, there should be automatic connection to the Internet.

Setting up and enabling Wi-Fi

For settings wireless network data transfer via the Zixel router, you need to check the operation of the wi-fi module. To do this, go to the “Start” tab in the taskbar and type “device manager” in the search bar. After which the user must select the appropriate line, and a new window will open in which a list of functioning equipment will be indicated.

In the new window, select the line “ network adapters" and reveal the row hierarchy by opening the "+" icon. Below you will see lines with connected network devices, the name of one of which will contain “wirelessnetworkadapter”. The line icon should not contain additional marks in the form of an arrow in the background of the label itself. But if the mark is still there, then point the mouse cursor at the line of this device and click right button mouse, select the “enable” option.

No further configuration is required, because The Wi-Fi connection was configured automatically when creating the basic Internet connection setup.

Setting up IPTV digital television parameters

Since the ZYXEL KEENETIC LITE 2 router has the “IPTV” function, Special attention It’s worth paying attention to setting it up in this part. For example, Rostelecom IPTV is configured as follows:

Thus, the user receives not only good remedy for working on the Internet, but also for using TV services without additional equipment.

Setting up the ZYXEL KEENETIC LITE 2 router should not cause significant difficulties for the user, if he did not deviate from the proposed option for selecting Internet connection parameters. For this purpose, the manufacturer provides a procedure for automating the connection process and setting up network device. Therefore, when carrying out these operations, you should act in accordance with the prompts in order to avoid problems and malfunctions of the device. But if you couldn’t do it using the program automatic adjustment connections, you can make your own this procedure

using the tips described above. Zyxel Keenetic Lite 2, as well as connect it correctly and check the functionality of the configured network. Will also be given technical specifications

this network device and its capabilities. All this will allow you to get the most out of this router from one of the best manufacturers.

For which solution segment is this network device released? This network device is aimed at creating compact computer networks. Moreover, the wired part of such a network can include only 4 devices. But here's the support IPTV technologies allows you to connect the appropriate set-top box to it and be able to view television channels . Another one This model is supported by SmartTV technology and the ability to use it to watch movies and other programs. In turn, the wireless segment of such a network has an increased coverage area (up to 20 meters) and 2 times the information transmission speed (in this case, the value is limited to 300 Mbit/s). Another important feature of this router model is the simple and truly intuitive Zyxel Keenetic Lite 2. For dummies, everything will be described in detail below.

Technical plan router parameters

The technical characteristics of this network device are as follows:

Supported wireless technology 802.11. Moreover, the router is capable of exchanging data with three of its modifications, which are designated n, g and b. The first of them can, according to the documentation, provide even 300 Mbit/s in the wireless segment.

It is possible to create a wired segment of local computer network. Maximum amount In this case there can be 4 devices, and the speed is 100 Mbit/s.

It is possible to connect an IPTV set-top box and watch television channels.

Configuring the Zyxel Keenetic Lite II router can be done using the web configurator, which has a simple and clear interface, and also allows you to configure the software component of the network device as quickly as possible.

What's included in the package?

Included in delivery in this case includes the following:

Router Zyxel Keenetic Lite II.

Settings, description, characteristics, etc. important information information about this device is provided in the instruction manual.

Meter wire for setting up the router.

Direct current.

Warranty card.

CD with a set of drivers for different versions operating systems And electronic versions complete documentation.

Where is the best place to install the router?

Before setting up the Zyxel Keenetic Lite 2 router, you need to choose the right place to install it. In this case, the following requirements are put forward to him:

There should be an outlet nearby to organize the power supply to the network device.

The cable from the provider should reach this location without problems.

The router itself should be as close to the center of the coverage area as possible. This will allow you to get almost anywhere high level signal.

There should be no metal objects or surfaces near the router installation site. Failure to comply with this condition will result in a decrease in the range of the wireless part of the local network.

The network device case can be either vertical or horizontal position. But antennas must only be in vertical position. This will allow you to get the maximum possible Wi-Fi coverage area.

Setting up a personal computer to connect to a network

At the first stage, you need to correctly configure the network connection of your personal computer. Therefore, we perform the following manipulations:

You need to go to this address: Start → Control Panel → Network Management → Adapter Settings.

In the network card settings window that opens, select “TCP/IPv4” and open it.

All checkboxes must be set to automatic receipt addresses from the router.

Switching

The next step in how to configure the Zyxel Keenetic Lite 2 router is switching the router. It is performed on completely switched off equipment that is part of the network, and consists of the following manipulations:

We screw on the antennas to organize a wireless network.

We install the power adapter of the network device into an outlet, and the wire from it into the router.

We assemble the wired part of the network. We connect the wire from the provider to the port labeled “Internet”. We connect to the “Home Network” ports with numbers from 1 to 4 internal devices networks (IPTV set-top box, TV with SmartTV function, computer and other devices). One must be connected to the network through them Personal Computer or a laptop, with the help of which the software parameters of the router will be adjusted.

Software configuration of the router

Then the router is configured software. It includes the following actions:

We check the correctness of the previously assembled circuit. We turn on the router and computer. We wait for each of them to finish loading.

We launch the browser on the computer. In the line for dialing network addresses, enter “My.Keenetic.Net” and press the Enter key.

After these steps, a window will appear asking for a username and password to access program parameters router. In the first of them we type admin, and in the second - 1234. After that, press the “Enter” button.

In the window that opens, select “Web Configurator”.

Then it is necessary to new form will change the administrator password, which must be entered in two different fields and confirm the changes made.

Then at the bottom of the interface we find the “Internet” item and go into it. Next, select the item called “Broadband connection”. In the form that opens, you need to set the following parameter values:

Check the box next to the input port (to which the provider cable is connected) and the connection port IPTV set-top boxes. Similarly, check the “Enable” and “Internet access” checkboxes.
The network ID must be 2.
The parameter setting should be “Automatic”.
In the "MAC Address" drop-down list, the "Default" value must be selected.
Set the MTU size to 1500.

We save these parameters using the “Apply” button.

Go to the bottom of the interface to the “Home Network” item and set the following parameters:

Leave the IP address and subnet mask unchanged.
Enable using the checkbox (this will allow new devices to automatically receive network addresses).
Set the initial network address at your own discretion, for example 192.168.1.18.
We also set the address pool at our discretion. For example, 50.
Click the “Apply” button.

At the next stage, go to the “ Wi-Fi network" and set its values:

Set the network name at your discretion.

We set the wireless network key in the same way.

We leave the remaining parameters unchanged.

After this, you need to click the button labeled “Apply”.

Go to the “Security” item at the bottom of the menu. Move to the “Yandex. DNS". Uncheck the box next to the “Enable” option.

Close the browser window after checking.

Checking that Wi-Fi is configured correctly and is working properly

This completes the software configuration of the Zyxel Keenetic Lite II 2 router. After that wired network already operates successfully provided correct settings devices. But the wireless part needs to be checked. To do this on any affordable smartphone or tablet in the settings we find the item “Wireless networks”. We find in it the item responsible for Wi-Fi work, and run it in scanning mode.

When finished, a list will appear available networks. We find the one that is ours. We connect to it and when prompted, enter the access key. After that, close this window, launch the e-mail client and check for new letters on email box. If everything is done correctly, the list will be updated. Otherwise, we look for errors in the settings of the router or mobile device.

Opinion of owners and current price of the router

Review and indicate that this is one of the the best routers in your class. Its price today is 4,500 rubles. Reviews also highlight its support for such popular functions as IPTV and SmartTV. It is due to their support that the hero of this review stands out from the competition.

Summary

Within the framework of this material, not only the algorithm of how to configure the Zyxel Keenetic Lite 2 router, but also other important information about it was described step by step. These include technical parameters, equipment, and preparation of the computer for network connection, and switching, and testing the computer network, and checking its performance. Otherwise, it can be noted that this router is excellent for creating a home network. It can also be perfectly used for implementing small office networks.

Setting up a router after purchase is not an easy process for the average inexperienced user, so we present to your attention detailed instructions, with which Zyxel setup Keeneticlite Lite 2 can be simplified as much as possible. And the process will be successful on the first try. So, now let's move directly to the instructions for Zyxel company to the network, having first considered some of the features of this device. What is this router?

Appearance

Externally, the router looks extremely presentable: a rectangular body made of black plastic, suggesting horizontal arrangement on the table, which is extremely convenient compared to the vertical one, in which routers, even with a slight shake of the table, often tip over on the table. There will be no such problem here one hundred percent.

Most of the upper surface of the body is textured with matte stripes that imitate ripples on the water. Only the lower right quarter, on which the power button is located, is left glossy. On the front edge, facing directly towards the user, there are indicator lights power supply, local network connection and internet cable. On the reverse side there are ports for connecting cables and two symmetrically located antennas.

Connection

Connecting Zyxel Keenetic Lite 2 is of paramount importance. The mains power supply is always connected first, then the Internet cable and local cord, connecting the router to the computer. Then we turn on the router itself by pressing the button on the top surface; after a couple of seconds, the power and connection to the telephone network indicators should light up.

Zyxel Keenetic Lite 2 router: setting up a network card

Next we need to make sure that our local connection works fine. Go to the Start menu, select Control Panel. In the pop-up window, click on the line “Network and Internet”. Next, “Network and Sharing Center”, in the left menu of which you need to select “Change adapter settings”. All you have to do is select “Local Area Connection” and go into its properties. In the pop-up window you are interested in the lines “Internet Protocol versions 6 and 4”. We open the properties of each of them one by one, where opposite the instructions “Obtain an IP/DNS address automatically” you need to check the boxes.

Now, if you have done everything according to the instructions given, an icon in the form of a monitor with a yellow triangle should appear in the lower right corner of your screen. This indicates that hardware device connected correctly. All that's left to do is set up the connection and a couple of additional functions.

Zyxel Keenetic Lite 2: setting up an Internet connection

You have already finished setting up your network card and are ready to start setting up your connection. The first thing you need to do is open your browser (even an old one will do Internet Explorer) and go to the router site. To do this, enter “192.168.1.1” in the address bar of the browser.

When you log in, the system will ask you to install Zyxel password Keenetic Lite 2. Invent it and, repeating it twice, apply it.

After you set a new password, you will be asked to log in. By default, the login is admin, and in the password column we enter the one we just created.

Next, at the bottom of the screen we find an icon in the form of a sphere with stripes crossing it, reminiscent of a network, click on it and get to the connection settings section. Select the “PPPoE/VPN” column and click the “Add connection” button.

For Zyxel Keenetic Lite 2, setup occurs by filling out lines in a kind of questionnaire. Here's what you'll have to fill out:

Type (protocol): PPPoE.

Connection via: Broadband Connection (ISP).

Username\password: this is your login\password specified in the agreement with the provider.

Configuring IP parameters: automatic.

Blank fields are only filled in if directly requested by your provider.

Click the apply button. This completes the connection setup for Keenetic Lite 2.

Setting up Wi-Fi Keenetic Lite 2

Setting up a wireless signal for such a device is a necessity.

In the Zyxel Keenetic Lite 2 router, setting up a wireless network is extremely simple. Let's take a closer look at solving this issue.

In the same window, go to the “Wi-Fi” tab. In the selected window with the new “questionnaire” we only need to change a couple of lines, and everything will work. We are interested in the lines Name\Security\Network Key and Channel. The first is the name of your network, visible when connected. The second is a way to encrypt your signal. We recommend choosing WPA2-PSK. The key is also simple - it’s the password for your Wi-Fi, an eight-digit set of numbers and letters. Opposite the “Key” value you can set “Auto”, but if problems arise, you can select a separate channel from the list.

Setting up IPTV for Keenetic Lite 2

This router also gives you the opportunity to use television services without connecting third party devices. This option is called IPTV. In Zyxel Keenetik Lite 2, setting up this option will only take you a couple of minutes. Go to the "Internet" section, in it - to the "Connection" tab. In the list below there will be a Broadband Connection item. We select it and in the window that pops up, check the boxes next to the items “Enable” and “Use to access the Internet” and set the IP settings to automatic.

Conclusion

As a result of completing all the points in this article, you will be able to connect your computer to the Internet. Of course, the process itself is quite complex, and an inexperienced user is unlikely to cope with all the nuances and steps, but this is precisely why the instructions above were provided to help you.