We make installation media using Ultra ISO. Speakers, microphones and MIDI devices

Back in 2008, the 3rd version of the world famous USB standard was finally approved. Engineers from companies such as Intel, Microsoft, HP, etc. worked on its development. It was important that new standard remained compatible with old usb 2.0. All connected devices worked exactly the same as with the old standard. But the connection capacity has increased significantly. Now it was possible to transfer not 600 megabytes per second at maximum speed, but up to five gigabytes per second. Also, the current increased to 900 milliamps.

By the way, these USB connectors there is a whole bunch, so look at the photo above and remember what they are like.

How to install usb 3.0 on a computer

It seemed to everyone that within a few months the new device would appear, and the process of copying files would be ten times faster. I wanted flash drives and everything to work much faster. But Intel refused to introduce USB 3.0. to your 2011 devices. The standard was released, but there were no actual physical motherboards with integrated USB 3.0.

But on the market computer devices new devices appeared that made it possible to work with USB interface 3.0. Naturally, motherboards with such a controller appeared, but they also cost much more than similar analogues without the corresponding connector. In this case, what was invented to work with new usb standards?

So, many craftsmen realized that there is. This port provides very high throughput Compared to regular usb ports. Any motherboard has PCI express. It is this connector that graphic card manufacturers began to use.

Now the only thing left to do is to translate PCI Express to the transfer function USB data 3.0. To do this, you can go in two ways - solder the corresponding adapter yourself, or buy a special adapter in an online store, ready for use and providing a USB 3.0 standard signal at the output. The second method is the least labor-intensive and therefore users began to buy such boards. Here is an example of such a board - you plug it into the PCI and at the USB 3.0 output

However, over time, minor shortcomings of this connection were discovered. For example, it is very inconvenient when the new USB 3.0 connectors are located behind the case. Many system units are installed so that access to the rear of the case is limited. Therefore, you need to transfer the USB pins to the front side of the case. In this case, you need to buy the corresponding USB expansion board kit.

Another disadvantage of such a board is that one PCI Express can be occupied by the video card. But the other slot has a reduced speed, which the user may not even suspect. That's why

You need to install such an expansion card only with full confidence that the slot will work at full power, otherwise you will still be working with the same USB 2.0.

Click on your Android device right click and try updating your drivers. Search for drivers on your PC and select the SB MTP device from the list that appears. After reinstalling the driver, the Android smartphone can work. You can also remove the driver and reconnect Android via a cable - Windows 10 will install the driver automatically.

Android Settings

The OS settings on the smartphone could also have changed due to updates or installation of other software (especially not from the Play Store). Check whether the smartphone is connected to the computer in the correct mode. In charging, modem or camera mode, you won’t be able to view your smartphone’s files in Explorer. Look at the notifications to make sure your smartphone is connected correctly. The smartphone can be connected as a modem - in this mode it also does not show files in Explorer mode. Go to settings wireless networks Android and switch the corresponding slider to connect the device as usual.

other methods

If you think the problem is hidden in your phone (for example, if you frequently installed applications from other Play Market), try resetting to factory settings. Before doing this, it is better to save your personal files. And since the USB connection does not work, you will have to download personal information to the cloud. A hard reset may well restore the connection, but use this method only as a last resort. It would be a shame if the files on your phone are deleted and the connection still doesn’t work.

It would be a good idea to test your PC for malware. There are viruses that can block the transfer of information, including via USB. After all, sometimes the most banal solution can be the most effective.

Did you like the article? Thumbs up and subscribe Zen channel

In order not to miss interesting things, join the group In contact with

If the computer does not see Android via USB, then you will not be able to download photos, videos or music, install applications not from the Play Market, or flash the device. And this is very bad, because the functionality of the phone is not fully revealed due to some stupid error.

Someone might argue that you can flash a phone without a USB connection, but for transferring files there is Wi-Fi, instant messengers, cloud storage, and finally email. But I just can’t give up the USB connection, I constantly carry the cable with me and consider it one of the most convenient ways data transfer.

Checking the cable and port

Before you go into your phone settings, install drivers and curse the day you bought this Android, check the cable and USB port. I was once very surprised that the computer stopped identifying the smartphone, which it had previously seen perfectly well. It turned out that the cat liked the cable and chewed it through. From this situation I drew two conclusions: the wires must be put away in a box and inspected before connecting. The cat did not draw any conclusions. If no kinks, bites, breaks or other mechanical damage are found on the wire, check the USB port. Try connecting to a different connector or inserting another device into the same port - for example, a mouse.

If Windows XP is installed on your computer, then urgently look for an opportunity to upgrade to at least “seven”. But first you can just install MTP protocol so that XP learns to work with Android. The trick is that when the first version of Android appeared, Microsoft released already Windows 7. Therefore, there is no MTP protocol in XP, and you have to install it separately. You can download MTP

If the computer detects any other device, but the phone categorically does not want to see it, then it’s time to shift the focus to Android settings and connection features. Yes, there is a possibility of mechanical damage to the microUSB connector on the phone, but I have not encountered this yet. If you have something broken, you will most likely notice it.

Most often, the inability to establish a connection between the computer and the phone is due to software errors. If none of the methods listed below resolve the problem, contact service center- it seems that the smartphone really needs repair.

Android setup

I came across two situations. The first phone required not only obtaining developer rights and enabling USB debugging, but also installing phone drivers on the computer. In the settings of the second smartphone, I did not find any parameters responsible for connecting via USB. They are not needed: the phone is perfectly detected by the computer, after which it offers to select a connection mode.

So, if you connected your smartphone, but nothing happened:

Open Android Settings.
Go to the section "About the phone"(may be called “About device”).
Find build number(models) and click on this item until a notification appears that you will soon become a developer. Usually n press 7-10 times.

After you become a developer, you will see in the Android settings new section - "Developer Options". Inside it you will find a switch "USB Debugging", which needs to be moved to position "On".

Now try connecting your phone to your computer again. When connecting, a mode selection window should appear on the smartphone screen. The default setting on older versions of Android is “Charge Only”. If the window does not appear, slide it out of the notification shade.

To transfer files, you need to select media device (MTP) or storage mode. Among the options there will also be a PTP mode, but it is only suitable for photos that can just as easily be moved to MTP.

After selecting the appropriate mode in “Computer” on Windows, a media device will appear, the contents of which you can work with. Depending on the features of phone models and versions Android internal Memory and SD card can be displayed together or as separate drives. But this does not matter, the main thing is that they are displayed at all.

IN Android settings There are no other parameters responsible for connecting via USB, except for debugging. However, there are some peculiarities. For example, on Nexus smartphones need to unlock a password-protected screen or graphic key to allow the computer to access the contents of memory.

Also, USB connection cannot be established if tethering mode is enabled on Android. To check its status and disable it if necessary:

Open Settings.
In chapter "Network and Connections" click « Additional settings» or "More".
Go to modem mode and disable the point WLAN access . If it is disabled, you do not need to do anything else.

Some manufacturers offer users special programs to control smartphones on a computer, but you can establish a simple connection via USB without this software. Utilities from manufacturers are needed not for the banal transfer of photos, but for performing more complex tasks: phone software updates via computer, device firmware, factory reset.

The reason that the computer does not see Android via USB may be an incorrectly installed or simply crooked custom firmware. In addition, sometimes resetting the settings helps, but before you do it, do not forget to do backup copy data as they will be deleted. The problem may disappear even after a normal reboot of the smartphone - keep this in mind.

Checking Energy Saving Settings

Windows is trying to save energy so that the same laptops can last longer on battery power. One of the saving factors is automatic shutdown USB ports. Sometimes this results in external devices not connecting at all. To check these settings and troubleshoot any deficiencies:

I haven't measured how much it affects the duration battery life a ban on automatically disabling ports, but there is no noticeable difference. But problems with connecting external devices such as Android phones are eliminated.

Installing drivers

The first time you connect any Windows devices installs drivers for it. Often this process goes unnoticed and very quickly (as was the case with my second phone), so you may not even know that the smartphone software is on your computer. But it exists, which means it should work correctly.

Connect your phone to your computer.
Open device Manager. On Windows 10, the corresponding item is in the context menu, called up by right-clicking on “Start”. In more earlier versions Windows Manager can be found in Control panels in viewing mode "Icons".
Check all USB controllers. If near one of them stands Exclamation point, then this indicates a problem with the software.

To make sure that it is the phone that is marked in the Manager, turn off USB cable. If the problematic controller disappears, then you have found the source of the problem. A smartphone without drivers may also appear in other sections: for example, among other or portable devices.

So, you discovered that something strange is happening with your phone drivers. What to do next?

Connect your phone so it appears in Device Manager.
Select it and delete it.
Update the hardware configuration so that the computer detects the phone again and begins installing drivers.

You don't have to remove the device, just update the driver. Right click on the phone, select tab "Driver" and press "Update". Another option is to install it first and then install it again without touching the device itself.

In the search box, select automatic detection. If you downloaded the phone driver from the official website, you can click "Search this computer" and indicate the path to the downloaded software file.

If you have chinese smartphone, then there may be another problem with it - the inability to find suitable driver in the Internet. They are often posted on forums like w3bsit3-dns.com, but if there is nothing, try installing universal driver. It's called Universal Adb Driver and is designed to provide proper operation Android Debug Bridge and PC synchronization utilities with Android devices. Versatility is not always good, but chances are that in the case of Chinese phone you can easily access the contents of memory.

Troubleshooting error code 19

If, when you connect your phone, your computer displays a message about the inability to start the device due to incomplete or damaged settings, you need to check system registry. But be careful: deleting the wrong entries can cause Windows to stop working.

After removing the setting, restart your computer and try connecting your phone again.

Alternative file transfer methods

If you were unable to resolve the USB connection problem and need to transfer files right away, use one of the alternative methods.

Sync your data via Google Drive. For normal Android work account required Google entry, so you definitely have access to cloud storage. You can transfer files through other services – DropBox, OneDrive. I use Yandex.Disk.
Transfer files via email, messengers or social networks. I often add small files to Documents on VKontakte, and then download them to my computer.
Install on your phone AirDroid app and access memory through a browser on your computer.

You can come up with other options. For example, create FTP server on your phone or configure remote connection via TeamViewer. So USB is not the only option. But if wired connection is not installed, it’s still worth looking at what the reason is and, if possible, eliminating it.

Also on the site:

The computer does not see Android via USB updated: February 7, 2018 by: Sergey

USB technology is one of the most important of the many technologies that have had a huge impact in computer world. USB (Universal Serial Bus- “universal serial bus”) - serial interface data transfer for low- and medium-speed computer peripherals

This technology has made it truly easy and convenient work with printers, scanners and external devices data storage (external hard disks, USB flash drives). All installation steps USB devices came down to simple principle « Plug and play" Devices have become truly mobile precisely because of USB technology. Today, not only desktop PCs and laptops are equipped with USB ports, but also gaming devices, smartphones, cameras, navigators and many other devices.

Ports USB version 2.0 provide data transfer at speeds up to 480 Mbit/s, and the version USB 3.0 raises maximum speed transfers up to 5.0 Gbit/s. The USB symbol is a kind of trident, drawn both on USB devices and on computer connectors.

Technology USB already has been studied quite seriously and has undergone many improvements, so USB ports, when used correctly, rarely cause any problems, and troubleshooting problems associated with them does not cause much trouble. This article will outline the basic principles of troubleshooting USB ports.

But before we begin, it’s worth describing basic recommendations when working with USB ports and devices, connected to them:

- never connect devices with visible mechanical damage USB connectors, as well as devices with external damage to the housing or with a clear burning smell.

If on the mother USB board ports have mechanical damage, then it is better to disconnect them from motherboard(connectors on the front of the case) or cover with colored tape to prevent their use. If necessary, it is better to replace such ports in a workshop with new ones.

Try not to overload USB ports. Their current strength is strictly limited: 500 mA for USB 2.0 and 900 mA for version 3.0. Do not strive to increase the number of USB ports using various USB multipliers. Modern motherboards already have up to 10 ports, which is quite enough for home use. It's always safer to buy additional PCI or PCIe USB controller than working through a USB “tee”.

If the USB ports on a laptop stop working, then working on it becomes very difficult - you cannot connect a printer, a scanner, or a flash drive. And unlike desktop computer, installation additional USB The controller is a very expensive pleasure.

In many cases, when the error message " USB device not recognized "The problem may be in the USB port. This problem is usually solved quite easily, since it occurs mainly at the software level.

What to do if the USB ports do not work?

Any hardware device interacts with the installed operating system through special program - driver. Many problems with devices are solved with the help of drivers. The same is the case with non-functional USB ports. Below are a few ways to help you resolve USB fault ports at the software level.

If the USB ports suddenly stop working, and USB devices are not detected, then the most in a simple way The solution to this sudden problem will be to restart your computer. Just restart your computer. If there were no problems loading the drivers, this problem will be resolved after a reboot.

Update hardware configuration in Device Manager

If you restart your computer in this moment is not desirable (for example, due to performing some important operation), then you can “reload” the drivers without rebooting the entire computer via device Manager. To launch it on the shortcut " My computer» right-click and select the menu item « Management e". Or in the menu " Start» find the program « Execute"and after launching it, enter the command devmgmt.msc.

In the window that opens, left-click once on the list of devices and then click the tab " in the main menu Action", then point to " Update hardware configuration" See if the section “ USB controllers" If yes, then your problem is solved, the USB ports should work.

Another way to make it work USB ports- disconnect and then reinstall the USB controller. To do this you need to run again device Manager. In the list of equipment that you will see in the window that opens, find the USB controllers section. On each of the devices in this section, right-click and delete them all. Once you remove all controllers, simply restart your computer. The controllers will be reinstalled and the USB ports will become available again. This may solve your problem.

Update USB drivers-controllers

Another reason that USB ports do not work is damage to the USB controller drivers. The only way out is to find the correct drivers and reinstall them. To download the appropriate driver, you need to find out the manufacturer USB port devices (via it). Installation correct driver should solve this problem in an instant.

Disabling other USB devices

Sometimes USB ports do not work due to overload when too many USB devices are connected. USB hubs sometimes do not provide enough power to the devices connected to it. The connected device can consume all the permitted power of the computer's USB controllers. If the equipment is connected to a USB hub, then simply connect the device directly to a USB port on your computer.

You can also leave the device connected to the USB hub, but first disconnect other devices in the hub. For the future, purchase a USB hub with its own power supply that will provide sufficient power to all devices connected to it.

If none of the above methods worked, then it is likely that the USB ports were physically damaged. Or the USB controller is damaged, in particular south bridge motherboard. In this case, the best thing you can do is replace or repair the USB port controller at a service center.

Not every user has a DVD drive; moreover, Lately Rare PCs are equipped with them. But you still need to install the system and for this it is most convenient to use bootable USB flash drive. Let's figure out how to install Windows 7 from a flash drive - after all, you won't buy a DVD for this purpose.

Before proceeding with installation, please read carefully this article: Various difficulties may arise in the process, which can be solved using one of the methods described below.

The installation process itself can be divided into the following stages:

downloading the installation image;
computer preparation;
creating a bootable flash drive;
setting up PC BIOS;
Windows 7 installation.

Let's look at each stage in more detail.

Before you burn the image to a flash drive and install the system from it, you need to download it. Today there is great amount ready-made assemblies operating system, which are equipped with many applications and functions.

Very often in such distributions the default theme is changed or sound scheme. But not all users like such innovations. You only need to download original images created by Microsoft. A huge headquarters of the world's leading programmers does their job better than some artisanal modifier.

A little lower you will find a button where you can download a torrent file to download the Russian version of Windows 7 with 32 or 64-bit architecture. The file was taken from the official Microsoft website and is completely original. Proceed with the download, and when the download is complete, move on to the next step.

After the file is downloaded, open it using a torrent client. If you don't know how to work with such programs, follow our step by step instructions.

First, download the torrent client itself. This will be the qBittoorent application.
Install the program and use it to open the previously downloaded torrent file.

Choose Windows version 7 (in our case it’s professional 64 bit) and click “OK”.

After this, the operating system will begin loading at the maximum available speed.

Getting ready to install Windows 7

First of all, you need to copy to safe place all the information that is important to us is located on drive C. Each user stores data in their own way, so each user has their own choice of folders for backup. Most often these are folders: “Downloads”, “Desktop”, etc.

You can save files to another logical drive (the one on which the system will not be installed) or to external storage. You can also use cloud storage, if there is not too much data. For example, the Mail.ru cloud provides 100 GB of free space.

With an eye to the future, remember: while using your PC, you need to store your data on a disk other than the one on which the system is installed. Divide physical disk into partitions and save your files on any of them except the system one. To install Windows 7, a comfortable volume of 70–100 GB will be (depending on the type and amount of software used).

Another important point that should be taken into account before the installation begins is the drivers for our network card. If, after installing Windows 7, it turns out that there is no driver for the network card, additional difficulties will arise that will have to be solved using a second computer by transferring files from it via a flash drive.

If you just bought a computer, no valuable information it is not and cannot be, feel free to move on to the next section, without copying the data.

Create a bootable USB flash drive

In order to create bootable media and begin the operating system installation procedure, we will need:

USB flash drive with a capacity of 8 GB or more. Instead of a USB flash drive, you can use simple map memory with card reader;
"Seven" installation distribution with .iso extension;
a utility with which we will write an image to a flash drive;

Attention! Before you start creating installation media, remember that all data on it will be irretrievably destroyed.

Making installation media using Ultra ISO

Wide famous program for working with disk images can create boot drives. Let's look at the algorithm for recording Windows 7 to a USB device.

Download and install the Ultra ISO program from the link.
Run the resulting file and check the box to “I accept license agreement" Proceed to the next step by clicking “Next”.

Using the “Browse” button, select the installation path, then click “Next”.

We don’t change anything here and just move on.

The program is being installed, we are waiting for it to finish.

The Ultra ISO installation is complete, you can run it and go straight to creating a flash drive for installing Windows 7.

The Ultra ISO program can be launched in trial mode, so its functionality will not suffer at all. Click on the button marked in the picture.

Go to the “File” menu and click on the “Open” item.

Select the Windows 7 image we downloaded, and then “Open”.

Go to the “Startup” section and click on the item that we marked in the screenshot.

We make sure that the media we need is displayed in the devices at the top of the window and click on the “Format” button.

Attention! This will destroy all your data beyond recovery. If you have the files you need on your USB drive, save them first.

In the next window, simply click “Start”.

Ultra ISO will once again warn us that all information from the flash drive will be erased. Click "OK".

After formatting is completed, click on “Burn”.

The process of recording “Seven” onto a flash drive has begun. It will take about 5-10 minutes depending on the speed of the drive and the selected OS version.

The recording is complete, our media can be used.

Let's look at a few more options for creating bootable media with Windows 7.

Rufus

This is another program that can create a bootable USB flash drive with “Seven”. First, let's download it.

The application, unlike Ultra ISO, does not require installation, so you can run the downloaded file and immediately proceed to the process of burning the OS to a USB device. To do this we do the following:

Select the recording device. This will be our flash drive, in in this case– 16 GB. Then click on the disk icon.

Select the distribution we downloaded in the PC folder.

We begin the recording process with the “Start” button.

Rufus will notify us that all files will be deleted from the flash drive. If you have already created a backup copy or there was no important information on the media, click “OK”.

As a result, it will begin Windows entry 7 onto a flash drive, upon completion of which you will have a full installation media.

Attention! Before you begin the process of writing the system to a flash drive, be sure to save all the data on it - otherwise they will be irretrievably lost.

As we see, this method turned out to be much simpler than the previous one, but we will not dwell on this and will consider several more options for recording Windows 7 to a USB drive.

Making a bootable USB flash drive using WinSetupFromUSB

Another application focused solely on writing operating system files to an external drive. Let's take a look at the utility and look at the process of working with it.

Select the path where the program will be unpacked (click on the button with the image of three dots) and click “Extract”.

We are waiting for all the necessary files to be unzipped.

We open the directory into which the unpacking was carried out and launch the program depending on the architecture on which your operating system is built. For us it is 64 bit, so we click on the marked file.

We insert our flash drive into the USB port and make sure that it appears in WinSetupFromUSB. Next, check the box marked “2” in the screenshot. When the bird is placed, click on the icon with the image of three dots, marked with the number “3”.

Select the image of our operating system and click on “Open”.

All that remains is to press the “GO” key and Windows 7 recording will begin.

Windows 7 is being written to an external drive. Once the process is completed, the flash drive can be used to install the system.

We will not stop at WinSetupFromUSB and will tell you how to burn the OS to media via Windows 7 USB/DVD Download Tool from Microsoft.

Windows 7 USB/DVD Download Tool

This official application from Microsoft, so it should, in theory, do the best job of writing Windows 7 to a flash drive. Let's get started with the program.

First, download the utility from the link from the official website. Then we launch it and click on the “Next” button.

We are waiting for the program to install.

We complete the installation process by clicking on the “Finish” button.

Let's move on to working with the program. Initially, we need to specify the file that we will record. To do this, click the “Browse” button.

After the path to the image file is registered, you can proceed to next step– click “Next”.

Here we should select the type of media on which we will install the “Seven”. Since we have this flash drive, we click on “USB device”.

We make sure that our drive is displayed in the field marked with the number “1” and click on the “Begin copying” button.

After this, we will be warned that all information from the media will be erased and after confirmation the process will start Windows migration 7 to USB stick.

Upon completion, we will receive a bootable USB flash drive, with which it is easy to install the OS on your computer.

For the program to work you need Microsoft library.NET Framework 2.0. If you do not have it, then download the program from the official Microsoft website.

We use the UNetBootin program

The UNetBootin utility is completely free. you can download it without registering or sending SMS. The program does not need to be installed - it works immediately after downloading. An application was created not only for recording on Windows flash drive, but also other operating systems such as Linux or Mac OS.

Let's move on to the instructions for using the application.

First of all, check the “Disk Image” box and click on the button with the ellipsis. In the window that opens, we need a Windows distribution.

In the drop-down list indicated by the number “1”, select a USB device, indicate our flash drive and click “OK”.

The application will warn us that all data that is already on the flash drive will be irretrievably lost. If we don’t need them, click “Yes to All”.

The distribution package is being written to a USB device. Once it is completed, the flash drive can be used to install the OS.

Command line

You can create bootable media with “Seven” without using any programs using the system itself. For this we will use the command line.

The entire process is described in the form of detailed step-by-step instructions, each stage of which is accompanied by a screenshot for clarity.

Initially, launch the command line. This must be done exclusively as an administrator. We will create bootable media at Windows example 10, but you can get the same result on Windows 7 - 8. Press the Win + R button combination and in the window that appears, press the “Browse” key.

We follow the path indicated in the screenshot with the number “1” and find cmd app. Click on it right key our manipulator and select “Run as administrator”.

We write to command line command diskpart and press Enter.

To start recording to a disk, you must initially select it, and take this choice responsibly, because all data from it will be deleted. You can view a list of disks using the operators: “list disk”, “list volume” or “list partition”. The first two show a list of disks, the third displays the number of partitions and their names. Insert the flash drive into the USB port and enter the “list disk” command in DISKPART. Next press Enter. You will see a list of all drives currently installed in the PC.

Select the disk that we need. To do this, enter select disk disk_number. The disk number can be viewed in the previous step; for us it is “1” since its size is 14 GB, which corresponds to our flash drive.

We remove the disk with the clean command. Make sure you do it again right choice– all data on the media will be completely deleted.

Now we need to create the main partition for the flash drive, from which we will boot in the future. Enter the command create partition primary and press Enter.

We set the drive letter using the assign letter=drive_letter operator. Let's do that. We know that our PC has drives C, D and E - therefore, we specify F. The final command will look like this: assign letter=F.

You can also specify the partition size. If you skip this step, it will take everything free place. Set size logical drive You can use the command create partition primary size=disk_size. The size must be specified in megabytes.

Select our disk using the select partition 1 command (indicate your disk number) and press Enter.

Now we need to make our section active. To do this, use the active operator.

All that remains is to format the flash drive - write a command like this: format fs=fat32 quick.

Exit DISKPART using the exit command. Now you need to prepare the files for recording. We unpack our Windows 7 image using any archiver (we will use the usual WinRAR) and extract all the files to our flash drive.

The installation media is ready and you can use it.

We use the WinToFlash program

Let's describe the process of working with another program for recording Windows 7 and other operating systems on a USB drive. To get started, download the utility from the link from the official website.

Install the program and run it. In the window that opens, select the item marked with a red frame.

At the very top, select “Windows”, then indicate Windows 7 and press the button indicated in the screenshot with the number “3”.

We indicate the path to the Windows 7 image that we downloaded. To do this, click the “Select” button.

Click on “Add”.

We make sure that the flash drive we need is indicated as the target, and click “Run”.

After this, the process of creating bootable media with Windows 7 will begin, after which the device will be ready for use.

Burn a bootable USB flash drive using WinToBootic

This application is one of the most simple tools for recording operating systems on external media. To work with the utility, you do not need to install it, nor do you need administrator rights. It will work like with Windows files, and with her images. The interface here is simple, and the speed of the program is pleasing.

To burn Windows 7 to a USB flash drive via WinToBootic, do the following:

First, download the program from the link and launch it. Check the box next to “Quick Format” and click “Do It!”

We answer the request for formatting in the affirmative.

We are again notified that all data on the flash drive will be deleted. Don't forget to save important information from the media, if it is there, and click “OK”.

The preparation of the flash drive is completed, click “Thanks!”

Next, select the files that will be written to our flash drive. To do this, click the icon indicated in the screenshot and select the image we need.

Click the button to start the process again.

Windows 7 will begin recording to the USB flash drive. When it is finished, the device can be used to install the system.

How to boot from a flash drive

To successfully install Windows 7 from a flash drive, it is not enough for us to simply write operating system to the media, you also need to force the PC to boot from something other than hard drive, but from a USB drive. This can be done in two ways: either by modifying the BIOS, or through a special boot menu.

Regarding Boot Menu we can say that it starts different keys, depending on the model of computer or laptop. You can see which button is responsible for this on your device in the instructions for it. We provide a list of combinations for the main brands of computers and laptops:

Launching Boot Menu on PC:

Launching Boot Menu on a laptop:

Below is a list of keys that launch the BIOS on different computers and laptops:

For clarity, we will show the process of installing a flash drive as the first boot device using our PC as an example motherboard Asus:

We turn off or restart the computer and after it starts, press the button to go to the BIOS (for us it’s Del).

This is what the BIOS itself looks like.

Go to the Boot tab.

We install our USB drive as the first device.

The process is similar on different computers, although the names of the tabs and items may differ. To understand how to enter the BIOS of your PC, read the instructions for it.

Installing Windows 7 from a USB flash drive

Once the BIOS has been configured, you can go directly to Windows installation 7 from a flash drive. Let's get started.

Immediately after the system starts, you will see the following window (data for installing Windows 7 is being preloaded).

Set regional parameters. Select your system language, region of residence, and keyboard layout. If desired, all this data can be specified after Windows startup When the setup is complete, click “Next”.

At the next stage, simply click “Install”.

All you have to do is accept the license agreement and the installation will begin. Check the box as shown in the screenshot and click “Next”.

Select a mode complete installation- This is the so-called clean option, when all old data on the system partition is deleted.

We are in the section settings menu. Click on the entry outlined in red.

If your disk is not partitioned, you can do this here (for Windows 7, it would be best to use about 100 GB of free space, the rest will become drive D). Don't forget to format system partition before installing Windows on it. When the operation is completed, click on the “Next” button.

Finally started Windows installation. We are waiting for the process to be completed.

Next, the system will reboot and we will be greeted with the Windows startup screen

Initial optimization is underway. The system prepares all the necessary files.

System services begin to start.

After which we proceed to complete the Windows installation

We are again informed that we need to restart the computer.

The system will check how productive our video card is.

Now we need to provide our details. We write an arbitrary name and computer name. Then click “Next”.

If necessary, you can set a password that the system will request upon startup. We're missing out this step, since the computer will be at home.

If you have Windows key 7, you can enter it here, however, you can do this even after the system starts. We are skipping this step.

We choose the system protection option depending on our personal preferences. We will be installing another antivirus, so the regular one will not be needed.

Enter the time and time zone. Then click “Next”.

We decide on the type of network. It's pretty important step, since if we indicate home network, and if we are connected to the public one, our security will suffer greatly.

Settings are being applied and automatic setting networks.

Last minute of optimization before our Windows 7 launches.

As a result, we installed Windows 7 from a flash drive, the creation of which was described above.

Instead of an afterword

We've looked at a ton different programs and tools from Windows itself to answer the question: how to install Windows 7 from a flash drive. However, these are not all options. There are a lot of such programs on the Internet. They differ in their convenience and functionality. Some utilities are better suited for ordinary users, the second - for professionals.

Which method to choose and how to burn Windows 7 to a flash drive should be determined based on purely personal preferences. Use the option that you like, and if you have any questions, ask us in the comments. We are committed to the shortest possible time give a comprehensive answer.