Increase RAM on HP laptop. Step-by-step instructions for increasing the amount of RAM in an Asus laptop. Find out the type of RAM

The need to know how to increase RAM on a laptop appears in cases where the RAM already installed on the device is not enough to run the games you need or programs.

It is very important to resolve this issue in advance, since a module designed to operate on a different bus or a larger volume than supported by the laptop will not work.

If a module is not changed, but added, its frequency and volume must match the parameters of the already installed one.

Although the device will be able to work with different strips, it will most likely be much slower - and great benefit there will be no such replacement.

For example, you are unlikely to notice an increase in performance when adding another 1–2 GB module to a 4 GB module installed in one slot, although you will spend some money and time on this.

The cost of memory for laptops is currently practically no different from computer memory. However, it has a special slot size, half the size compared to the connectors in a PC.

For laptop computers a smaller version is required, SO-DIMM, which should be taken into account when ordering RAM in an online store or in a regular store point of sale.

Advice: If there are no RAM chips for your laptop on sale anymore (for example, it supports the outdated DDR2 type), you still need to decide whether it’s worth increasing the memory, or whether it’s better to purchase new gadget.

Memory installation

When the memory has already been selected and purchased, they proceed to installing it on the laptop.

On some models Asus type To do this you will have to remove the whole back cover and remove other elements that interfere with replacing or adding RAM.

Most often this applies to compact devices – mini-laptops and netbooks.

Most more modern devices allow you to replace and add a bar, spending no more than 2-3 minutes. To do this you just need to:

1. Disconnect the device from the network;
2. Take out the battery;
3. Open the cover of the memory module compartment;
4. Remove old microcircuits (if they are being replaced), taking into account that they can be held on by latches;
5. Install new memory until the latch snaps into place;
6. Replace the battery;
7. Close the lid.

You can make sure that everything is done correctly after turning on Windows and volume checks installed RAM in computer properties.

When upgrading memory, you should make sure that your actions do not violate the warranty on the new device.

In addition, if the back cover is for quick access There is no access to RAM, you should read the instruction manual for this model.

In some Lenovo models you even have to remove it to install it HDD. Older laptops may require even more complex actions.

For example, sometimes one or two strips are installed in different places.

Increasing memory using a flash drive

There is also a simpler and cheaper option to increase the RAM of a laptop - without even opening its case or buying new modules.

All that is required from the user is to have a free flash drive with a capacity of 4–16 GB and installed Windows 7 or more new version.

In principle, the same method is suitable for a stationary PC, the memory of which is not enough for any actions or the operating speed is simply too low for the user’s purposes.

Reasons for choosing this method

The main reasons to choose a way to increase laptop RAM using a flash drive can be:

• reluctance to spend money on improving the equipment when replacing the device with a new one in the near future;
• lack of physical ability to install or replace the bracket (outdated module type, faulty slot, etc.);
• the need to increase memory precisely in this moment.

Operating principle

In the operating room Windows system 7 it is possible to increase the RAM due to additional file swap created on the drive.

The utility that allows you to do this is called ReadyBoost.

And you can call it by simply opening the properties of the flash drive and selecting the tab with the appropriate name.

Using this system feature allows you to increase physical memory by the following amount:

• up to 256 GB for 64-bit Windows 7;
• up to 32 GB for Windows 7 32-bit;
• up to 4 GB on other OSes, including XP, if you download the utility additionally (it is not built into the OS).

That is, if the laptop has 2 GB of RAM, it is not advisable to make the page file size on the flash drive larger than 5 GB.

The effectiveness of the method is quite decent - when reading small files, the speed increases by about 5–10 times.

However, when working with large areas of data, the difference will be almost imperceptible.

Process of increasing memory

To increase memory you will need:

1. Take any free flash drive with an interface of at least USB 2.0. However best choice will become USB use 3.0, the data transfer speed (up to 5 Gbit/s) is comparable to the parameters of DDR3 memory modules;
2. Insert device into USB port;
3. Format the flash drive (not necessary, but recommended) in NTFS format, which will increase the capacity possible memory from a maximum of 4 GB for FAT32 to a much larger size.
4. If there is any data on the media, you should uncheck the “Clear table of contents” checkbox. This will increase formatting time, but guarantees complete removal data that will now be used as RAM.

After a few minutes, a message indicating that formatting is complete will appear on the screen.

And after selecting the ReadyBoost tab in the properties of the flash drive, you can configure the required amount of memory increase.

So, for example, if the storage capacity is 16 GB, the laptop can use more than 15 of them.

In this case, the flash drive cannot be used to store data, and when viewing its properties, the following information:

It is entirely acceptable to use less flash drive memory. In this case, it can be used for other purposes.

However, before removing the device from the USB port, you should cancel ReadyBoost by opening the disk properties and the utility tab again, but selecting “Do not use this device.”

Such actions will not always speed up the operation of your games and “heavy” applications. But at least this method is guaranteed to increase the speed of opening photos and videos.

According to users who have tried it this technique, the browser also works faster after using it.

Laptops are essentially the same computers, only portable. Because of this useful property, like mobility, you have to sacrifice something. IN in this case You sacrifice their maintainability and power. Unfortunately, the processor in them, like the video chip, cannot be changed, but you can increase the volume random access memory. Most more or less modern laptops have two RAM slots, often only one of them is occupied, which allows you to expand the RAM.

Today, laptops can have up to 32 GB of RAM, but if you decide to increase the volume, you probably have less RAM. The biggest disadvantage of all laptops is that you need to disassemble them with caution, one awkward movement and you can bend a contact somewhere, and this, in turn, is fraught with a short circuit. You don’t need to be an electrician or a person versed in technology to understand what exactly a short circuit leads to. In this case, it will result in burnt fuses, or even a completely burnt motherboard. So be careful!

Increasing the amount of RAM on laptops

First, I would like to start with the basics. If you have a very old laptop and it only has 1-2 GB of RAM, but technical specifications it supports as many as four gigabytes, you should know one thing. Over 3.5 GB of RAM you need to install 64-bit operating system.

It should also be mentioned that there are different types memory. At the time of writing, there are four of them - DDR1 - DDR5. They differ from each other in different frequencies and, accordingly, speed of operation.

Also, RAM can be one-, two-, three- and four-channel. That is, one, two, three or four slots work together. The more threads, the higher the final computing speed. The performance gains are especially noticeable in games. graphic editors and browsers (if open a large number of tabs).

How to find out what type of RAM is in my laptop

There are two options here - unscrew the laptop, remove the cover and look at the sticker on the RAM for its type - it will indicate both the frequency at which it operates and the type. The second option is simpler - software, just download a free utility called CPU-Z. You decide. If you want to expand the capacity of the RAM, you will still have to unscrew the cover and remove the memory from there. let's consider software method:

Determining the number of RAM slots on a laptop

Now we need to determine the number of slots in the laptop. Because how to expand the amount of RAM if you only have one slot? In this case, we will simply have to install a bar with a larger amount of memory instead of the one currently installed. To determine the number of slots, you need:

The most interesting thing remains - to set the second bar. According to technical characteristics this laptop Supports up to 6 gigabytes of RAM. In other words, we can set the bar to another two gigabytes and the laptop will work more quickly.

How to install RAM on a laptop

Depending on the manufacturer and specific model In a laptop, the amount of RAM increases in different ways, or rather, in some places it’s harder to get to the memory slots, and in others it’s easier.

For example, with regard to ASUS laptops, you will need to completely remove the back cover, and then the keyboard, after which you can insert the bar next to the first one.

On some older laptops everything is much simpler; there is a separate section where the RAM is:


As you can see, with good instructions you can easily cope with this non-trivial task, like increasing the amount of RAM on a laptop.

Those who are in force professional activity or personal reasons, they often work on a laptop, they fully understand that the speed of execution of many programs fully depends on the size of RAM. It is for this reason that many PC owners are actively interested in how to increase RAM on a laptop.

Adding RAM to a laptop will not take much time, but it will save you waiting for programs to load.

The technical parameters of different laptops differ significantly, so it is absolutely impossible to navigate and purchase RAM that someone you know purchased. In this regard, the first rule arises, which the owner must take into account when there is a desire to increase RAM. It lies in the fact that it is first important to determine the type already installed module RAM, its volume, as well as bus frequency.

Determining RAM parameters by visual inspection

There are two options to obtain the necessary information, after which you can confidently answer the question whether it is possible to add RAM to a laptop. Without such preliminary work, the answer may be accompanied by errors, which is certainly undesirable.

The first option involves partial disassembly of the laptop, after which the user will be able to see with his own eyes the quantity already installed slots memory and also available empty space, to which you can also add additional slot. Unfortunately, if there is no room to add a new slot, then the user will have to choose between completely abandoning plans to increase RAM, or replacing one slot with another with a larger capacity.

Next, it is very important to determine the type of module that can be successfully “accepted” by the laptop. This information can be obtained either from the RAM module itself or from technical documentation, which was given to the owner in the store when purchasing the laptop.

It is also very important to know maximum frequency supported by the motherboard. This information can also be found in technical documentation or on the Internet.

Determining RAM parameters using the program

Despite the fact that the laptop does not have to be completely disassembled, many users refuse to perform such actions again. Programmers, meeting them halfway, developed a special software, allowing you to get answers to all the above questions without the need for disassembly.

A fairly useful program is CPU-Z; it is very popular among most users, since it provides the ability to easily determine all necessary information relatively motherboard, RAM and processor.

The CPU-Z program can be downloaded from various resources, but preference should be given only to those that have already been tested and can be trusted. After downloading, installation is carried out software product, then you need to click on the shortcut - CPU-Z will start and a program dialog box will appear on the screen.

Having studied the information on the two tabs of this software application, the user will be able to find out whether it is possible to increase the RAM on this laptop.

Initially, you should go to the “Memory” tab. At the top there are three key parameters that are important to pay attention to.

The first “Type” indicates what type of RAM is already installed and whether it can be added additionally on a specific laptop.

The second “Size” shows the amount of installed RAM. After reviewing this parameter, the user must finally clarify for himself whether anything should be done further. The problem is that 32-bit operating systems can only accept and use up to 3GB of RAM. Wanting to increase the volume by more than 3 GB, the user needs to initially reinstall the system, giving preference to the 64-bit one.

The “Dram Freguency” line indicates the memory bus frequency.

Next, you should go to the SPD tab, where you can get an answer to the question: “Is it possible to add additional modules and are there free slots?” Select the specified slots one by one from the drop-down list menu. If the slot is free, then when you select it, an empty window will be located opposite.

To determine the latter important parameter you will have to use Internet resources. Initially, on the “Mainbord” tab in the “Manufacturer and Model” field, select the model of the motherboard, as well as the manufacturer, then find the corresponding characteristics on the Internet.

Adding or replacing RAM

After all important items have been successfully collected Technical information about the laptop, it was purchased correctly additional module RAM, the user should familiarize himself with how to add RAM to a laptop.

Step-by-step steps for replacing memory

Initially, you should completely turn off the power to the laptop. For this purpose, it is completely turned off, disconnected Charger, remove the battery. Next, it is very important to press the power off button again, not paying attention to the fact that the laptop is already turned off. This repeated pressing allows you to completely remove static electricity.

Static electricity should also be removed from anyone who has started replacing the RAM slot on a laptop. First of all, you should exclude silk clothes, then touch the heating radiator with one hand and the unpainted part of the laptop with the other.

On the back of the case in the center there is a cover that needs to be unscrewed, since the memory slots are located behind it. If main goal If the task is to find out how to increase the amount of RAM on a laptop, then by adding an additional slot the user can only fill the empty space with a new module, thereby allowing to increase overall volume memory.

When installing two identical modules from the same manufacturer, you can almost double the speed of the laptop by activating the dual-channel operating mode.

If there is no free space to install a new module, then the user will first have to remove the old module by bending the clamps, and then install a new one. At correct installation the clamps should slam shut, accompanied by a characteristic click.

Finally, all that remains is to reinstall the protective cover and screw it tightly.

In some laptop models, memory slots are not installed with reverse side the case is under a separate cover, and under the keyboard, so if you want to increase the RAM, you will have to carry out the disassembly process, accompanied by greater responsibility and care. Initially, the keyboard is removed, after which the protective metal panels are unscrewed, then a new memory slot is installed and the laptop is assembled.

If any non-standard situations arise, it will be difficult for a beginner to solve them, so it is best to seek help from a qualified specialist who can quickly add new module, while increasing the total amount of RAM.

So, every user can increase the RAM on a laptop if they first study all the important information and follow the instructions. Additional memory will significantly improve the performance of the laptop and the user will appreciate the work done.

The need to know how to increase RAM on a laptop appears in cases where the RAM already installed on the device is not enough to run the necessary games or programs. This situation happens much more often with laptop PCs than with desktop PCs. If only because most of the characteristics of desktop and laptop models with the same price differ noticeably not in favor of the latter. This is explained by the desire of manufacturers of portable computers to place everything as compactly as possible - and this is usually enough for the average user, who primarily requires mobility from the device, rather than high performance.

It’s easy to avoid this problem - you just need to buy a laptop whose memory won’t have to be increased for another 3-4 years. For example, such as gaming models MSI brands with 16–32 GB of memory. True, their price will be no less than 100–150 thousand rubles, which is unlikely to suit regular user, who would prefer to better increase the RAM of an existing computer.

The first sign that it’s time to change the memory are messages about a lack of RAM or games and useful programs that won’t start at all. This is especially noticeable if the laptop model is not that old, but applications are still needed, for example, for work.

Files that do not open do not necessarily indicate that the entire device will have to be replaced. There is a possibility that the problem can be solved by simply adding 1-2 sticks of RAM. Moreover, some devices do not have enough memory - for example, for quad core processor the manufacturer can install only 4 GB, while the board supports both 8 and 16 GB.

Advice: When increasing memory, it is worth changing 32-bit Windows to 64-bit. After this, the RAM will be fully used. If this is not done, the system will only use 3 GB of memory.

If this is not done, the system will only use 3 GB of memory. The same applies to a 32-bit processor, but since they have not been produced for several years, the presence of such a component requires replacing not the memory, but the entire computer.

Memory selection

Before buying memory and increasing it, you should check whether this can be done, as well as the type of RAM and required amount slats. Any computer, desktop or laptop, can have as many modules as it has slots specially designed for this.

You can determine this amount visually by disassembling the laptop and looking at what memory is already installed there, and how much can be installed. However, the issue can be solved in a simpler way - for example, by downloading the free CPU-Z program, which will work in Windows 7 and more later versions operating system. The most convenient way to find and download the application completely free is on the official website of its manufacturer, CPUID.

After starting the program, a window with several tabs will open. One of them, SPD, will help determine which slots of your laptop are occupied, what type and amount of memory is already installed. The default slot number 1 displays information about device parameters. For the example given, this is a 4 GB DDR3 RAM stick. If two of the same boards are installed (for optimal performance a paired arrangement is required, i.e. 2 or 4 identical ones), and there are no other slots at all, to increase the volume you will need to complete replacement. For example, removing both 4 GB sticks and putting two 8 GB sticks in them. If only one slot is occupied, you can install the same memory in the second. Four connection spots are very rare on laptops.

There are other programs that can help you decide on the choice of memory. Some of them will show not only the parameters of the installed RAM and other components, but also the maximum storage capacity. And special software can even provide information about possible options for installing the slats. There are services that even contain links to pages with components where you can find out approximate cost memory, and evaluate your capabilities to increase it.

Memory acquisition

When purchasing a new RAM module, you should make sure whether it is possible to increase its frequency. Some laptop motherboards allow you to install DDR3 memory, for example, with data transfer rates from 1333 to 1866 million operations per second. Others already support more high frequency– up to 2400 MHz. You can find out which memory is suitable for your device by reading the information about the motherboard found online. It is very important to resolve this issue in advance, since a module designed to operate on a different bus or a larger volume than supported by the laptop will not work.

If a module is not changed, but added, its frequency and volume must match the parameters of the already installed one. Although the device will be able to work with different strips, it will most likely be much slower - and there will not be much benefit from such a replacement. So, for example, you are unlikely to notice an increase in performance when adding another 1-2 GB module to a 4 GB module installed in one slot, although you will spend some money and time on this.

The cost of memory for laptops is currently practically no different from computer memory. However, it has a special slot size, half the size compared to the connectors in a PC. For laptop computers, a smaller version, SO-DIMM, is required, which should be taken into account when ordering RAM in an online store or at a regular retail outlet.

Advice: If there are no RAM chips for your laptop on sale anymore (for example, it supports the still outdated DDR2 type), you still need to decide whether it’s worth increasing the memory, or whether it’s better to buy a new gadget.

Memory installation

When the memory has already been selected and purchased, they proceed to installing it on the laptop. On some models like Asus, this will require removing the entire back cover and removing other elements that interfere with replacing or adding RAM. Most often this applies to compact devices – mini-laptops and netbooks.

Hi all ! In today's article we will tell you how to install RAM correctly. Those who decided to add RAM to their computer have probably already chosen RAM for themselves. However, we recommend that you read our other publication, from which you will learn.

From the link above, you will learn that RAM is different and how much RAM you can install, and also that everything may not be so trivial in installing RAM for laptops. In addition, this article will be useful if you want to install additional RAM.

How to install RAM in a regular computer

So, you have already bought it and are holding it in your hands. required module. Generation of this module The RAM matches your motherboard. Also, do not forget that the amount of RAM must be such that the RAM module or modules can be supported by your motherboard.

In other words, before installing, make sure that your computer not only supports the available amount of memory modules, but also this specific generation, since RAM can be different: DDR, DDR2, DDR3, EDO, MicroDIMM, SDRAM And SODIMM. This is especially true when you need to install additional RAM. When installing or replacing RAM, some “experts” claim that the user may encounter the following problems:

1. With electrostatic charges.
2. Incorrect parameters in BIOS.
3. Incorrect installation DIMM modules.

On this basis, you can find stupid advice about adding RAM:

• To prevent the build-up of static electricity when working with sensitive chips, do not wear synthetic clothing or shoes with leather soles (or stand on a rubber mat).
• Remove accumulated electrostatic charge by grasping the housing system unit.
• You can also use a special grounding bracelet on your wrist, which can be purchased at an electronics store.

Just think about this nonsense! Shouldn't you wear a tin foil hat? Know that these problems are just made up by people who are far from reality. Of course, there are problems with statics and grounding of the computer case, but they happen rarely and have practically nothing to do with installing RAM.

However, it is worth noting here that if you want to install additional RAM, then the issue of module incompatibility may arise. But this has an indirect relation to the installation process itself.

The main thing before installation is to turn off the power to the computer and let it stand for about five minutes. Typically, installing RAM of the correct form factor takes about five minutes. To replace RAM memory in standard PCs, you should rely on the following tips:

1. Turn off your PC and disconnect network cable. Wait a while until the residual charge on the board disappears.
2. Open it up system unit. Usually the cover is held on by two or less often four screws.
3. Carefully move away any cables that might be obstructing free access memory connectors. Before disconnecting the wire, remember where it was connected, but it is better not to disconnect anything - in most cases, you can install RAM without any problems.
4. If you need to remove a module in order to install RAM of a larger capacity or frequency in its place, then simply move the side clamps that hold the module apart.
5. Most modern motherboards support dual-channel RAM. Its advantage is that memory modules work by cooperating with each other. You need to determine which connectors should be used for correct operation fees in two-channel mode. These connectors have different colors (in pairs). That is, when installing two identical memory modules, they should be placed in connectors of the same color.

There are special keys on the RIMM and DIMM strips that help ensure the correct orientation of the strip in the corresponding slot. That is, any form factor or generation of memory has its own key, according to which you need to set the RAM bar. Before inserting the module, you must make sure that the plastic latches located on the sides are moved apart:

After installing the RAM into the motherboard slot, just gently press on the module and the latches will snap into place.

If the interfering wires were disconnected before installation, return them to their place and close the cover of the system unit, connecting the power cable. After installing additional RAM, you may need to launch an application BIOS settings to save new settings, but usually the computer understands everything itself and the operating system will simply start loading normally. Overwhelming majority modern systems V automatic mode determine new size memory and make the necessary changes to the BIOS.

How to add RAM to a laptop

So we got to laptops. Installing RAM in a laptop is almost a lottery, since you first need to find out whether installation is possible in your specific laptop model. At the beginning of the article we already provided a link to the publication. Therefore, we will not focus on this.

The first thing you need to find out before adding RAM to a laptop is whether the laptop has an additional slot and whether it is occupied. This does not apply to the case when you want to replace RAM. Laptops are all different, so an additional memory slot may be missing or located in a hard-to-reach place. For example, like this:

Or like this:

Therefore, for many models, adding RAM to a laptop can be a problem. But more often, you just need to unscrew the lid on the bottom of the laptop:

Pull out the memory module, freeing it from special fasteners, if necessary, replace it:

And install the new SODIMM RAM in place:

After adding RAM, you can use special utility diagnostics and make sure that the memory is functioning correctly, but it is better to just go to the system properties and look at the amount of RAM used. We hope our article was useful and you managed to install the RAM correctly. Read!

• Elena

• ildar

  Hello, please tell me, Everest says 2 channels of memory devices, does this indicate that the laptop has 2 memory slots? Lenovo laptop, I took off the cover, but there seems to be only one slot.

• Ruslan

• Gennady

  Hello.
  Help me please.
  The computer (unit) is 6 years old.
  Windows XP
  The last 2 months began to slow down a lot. Cleaned the cache, defragmented both disks C and D.
  Drive C. Capacity 97.6 GB
  40.2 GB occupied
  Free 57.4 GB

  Drive D Capacity 135 GB
  28.6 GB occupied
  Free 106 GB

  It started to slow down especially when watching movies.

  Kaspersky.

  Absolutely everything is licensed.

• Andrey

  Hello!
  I have the following problem: a month ago my computer started to glitch - it turns on for 5 seconds, works and turns off, then turns on itself (the screen does not light up, there is no civilian boot)
  Having taken it to the repair center, they told me that the memory module had failed (burnt out), I had 2 memory modules and both 1Gb class DIMM DDR2 and both on Hynix chips, there was only one memory module left (everything worked but only with the brakes of 1Gb RAM XD. After I bought a 4Gb memory module of class-DIMM DDR3, also on a chip from Hynix.
  The problem is that, as I wrote above, my problem with turning it on and off was repeated with a new memory module. Removing the new memory module remains DDR2. Everything works as it was before.
  What is the problem?

• Kudesnik

• Nikitos

• Vladimir

  Hello. Can I add to the memory of Team Group TXD34096M1600HC7DC-L (2x2GB) New Kingston KHX1600C9D3B1K2/8GX (2x4GB) PC Motherboard Gigabyte board GA-H55M-USB3 Cori5 750 Windows7 64bit. Will the PC see 12GB of RAM? Thank you.

• Vladimir

  Hello. Please tell me why AIDA64 does not show the location of the memory strips correctly. In fact (I see it on the motherboard) there is one thing. And Aida is 64, on the contrary. Why? Please answer. I'm puzzled...

• Vladimir

• Imanzhan

  I have this problem, I had it at home
  2 GB of RAM, I installed it on the computer after a reboot it comes out blue screen death with some kind of inscription. What to do?? Help?

• firesystems

  Good afternoon The computer had 4 4 GB sticks. One of them is glitched (produces a blue screen of death). Question: is it advisable to use 12 Gb (asymmetrical), or is it better to use 2x4 for each channel (symmetrical).

• Alex

  Hello! I encountered this problem! I want to add RAM to my laptop! Lenovo b570e (59-355318) laptop in online stores in the description it says that there are 2 slots for RAM, but when I unscrew the back cover there is one slot, I removed the keyboard thinking that maybe there is another slot for RAM under the keyboard, but it wasn’t there .The question is whether the RAM slot could be located somewhere else in the laptop. Thank you!

• Zaire

  Hello, I have such a problem, my laptop is lagging, I decided to install additional RAM, but it didn’t help, it costs 2 GB of RAM, of course, it seems to me that the installed additional RAM does not work at full capacity, because when I look at the system properties, it shows me that the installed memory is 4 GB and only used 2GB, it doesn’t really take long to load, please help

• Dima

  Hello, I have such a problem, it costs 2GB of RAM, but they are different, but they are inserted as expected, and when I turn on a video on YouTube, the processor loads at 100%, and the video slows down, although the video card is good, could there be a problem in the RAM?

• Bogdan

  Hello!

  The other day I bought an asus k750j laptop, a fairly powerful machine, but when I try to play computer games, I get an error saying that there is not enough RAM to work with. This is extremely strange, because in my case latest laptop I had the same amount of RAM (6GB) and there were no problems. Maybe games just don't see my RAM? I would like to know how to solve this problem. And one more question, is it possible to transfer RAM from an old laptop (HP pavilion dv6) to a new one (Asus K750J)?
  Thanks in advance for your answers

• Dmitry 2014

  Hello! Please help, I have this problem, the RAM on my computer is 2 GB, I decided to install it additional memory for 4 GB, I did everything as expected, but the computer does not boot! Appears loading screen and that's where it hangs! OS Windows 7 32-bit!

• warmongerrr

  Hello! Please tell me my motherboard is M2N68-AM SE2 AMD processor Athlon II x2 240 will these DIMM sticks fit them DDRII 4096 MB PC-6400 (800MHz) SDRAM Corsair 2x2GB 5-5-5-18 TWIN2X4096-6400C5C thanks in advance!

• BOGAT

  Hello, please help me, I have a ga-8ipe1000mk motherboard with a Pentium 4 processor, I want to plug it in there AMD Athlon 64 3000 is this possible??? and another question: I have 4 slots for RAM in slots 2 and 3, there are 2 sticks of 256 ddr each, I want to add 2 more of 512 ddr, too, but when I start it asks safe mode Or did I try both options with normal loading? After choosing it, it doesn’t load anymore, what should I do? Tell me???

• Fds_256bit

  Hi. I bought myself 4GB of RAM, frequency 1600 MHz. The motherboard also had 4GB 1600 MHz. I turn on the computer, check the verification, look, it says that I have 8GB installed, 3.47 GB free. How so? I went into Aida64, it says What physical memory Free 3.47 GB, and virtual 6200 MB. Why, how is this possible? After all, I have 8 GB of RAM. Please help.

• Hucciboss

  Hello, I'm not very computer savvy and I have the same problem. I decided to add RAM (costs 512), and bought an additional bracket identical to the one in the computer. At first I decided to replace it completely, took out the old one, installed a new one, turned on the computer (immediately after installation), the black screen came on and there was no beeping sound when I turned on the computer.
  I decided to install it with the old bracket, I also turned it on immediately after installation, the screen started working, but the computer did not boot beyond “welcome”.
  After all this, I set the old bar again works, but the computer started to slow down horribly. What do you advise?

• tima010

• Valera

  Hello, please tell me I have an old computer with an Intel(R) Pentium(R) CPU 3.00Ghz processor, can it handle 8 GB of RAM if the old RAM costs 1 GB??

• TtT007

• Oleg

  Hello, I have the same problem; The motherboard has 2 1GB DD2 RAM chips. That is, these are the Makars: black slot 1, yellow 0, Black slot1, yellow 0. I add 2 1GB chips to the yellow slot, and a blue screen of death pops up. What to do? Cleanliness is the same, chips are similar to each other.

• Max

  Hello. I replaced the 2 gig DDR3 RAM with 2 DDR2 RAM with 1 gig memory just for fun. I installed my DDR3 and it starts but the blue screen is dead, what should I do?((
  Thanks for the early ones.

• Valera

• KSENIA

  Good evening)) I have a question, my mother is ASUS P5B SE, the RAM is DDR2, can I install DDR3? I heard that there are motherboards that come with both 2 and 3, but not together, please tell me in advance, thanks)))

• Paul

  Hello, the laptop had 4 GB of RAM, I installed 4 more. In total, 8, the system and task manager see all 8, BUT when I play, only 4 GB is used, although the FPS is low. the remaining 4 gigs remain empty. Windows 7 Home Basic 64-bit. What is the problem?

• Nikolay

  Good day! Tell me, please, I have 4 slots for RAM, on the first and third slots there is a gig, system seven, computer from 2006, does it make sense to add two more 512 RAMs to the second and fourth slots? The computer will not conflict, and will it see is he this extra gig? In general, how to properly distribute RAM among slots (for copper DDR2)?

• Said

  I wanted to change the RAM, I bought new ones the same as the old ones (ddr2), but after changing the RAM, an endless beep sounds, I inserted everything correctly, but it doesn’t work, and I also noticed one thing: there were two old RAMs, when I removed one it doesn’t work either, it works with only two strips, help if you know!

• Subject

  Hello! I have a question of the following nature: - I installed 2 sticks of 2 GB of RAM in my computer, when I check the characteristics, it says in brackets (4 GB installed), outside the brackets 3 GB are available, what does this mean? and is it possible to do something about it?

• Talsmir

  Hello, I want to add RAM, at the moment there are 2 pieces of Kingston HyperX KHX1866C9D3/2GX of 2GB each. I want to add DDR3 DIMM 2Gb PC10600 1333MHz CL9 Kingston (KVR13N9S6/2) Help me find out if they are compatible, if not, which one is better to add.

• Nikolay

  I have this problem. The computer was very slow and glitchy, and I decided to buy more RAM so that I wouldn’t have such problems. I installed everything as it should, but the computer couldn’t even turn on. I installed the old RAM back and it started working again. What's wrong? Motherboard model gigabye ga-z68ma-d2h-b3
  New RAM Kingston hx318c10fbk2/8

• Danil

  Hello. I have 2 GB DDR3 RAM. I have a total of two RAM slots and I decided to install another 4 GB DDR3 stick. If this stick is installed with the old 2 GB stick, then the computer sees only 2 GB. If you remove the 2GB stick and leave the 4GB stick, the computer simply doesn’t turn on, doesn’t even beep, although all the coolers are spinning. The AIDA64 program shows that I have both of these strips in my computer and that they both work!! I do not know what the problem is. Motherboard Asus P5G41T-M LX3. Bios updated.

• Anonymous

  I removed the RAM stick from the computer for a test, after I installed it, the computer did not start. Then I tried to insert another stick RAM, everything still didn’t start. I realized that I damaged the slot. Question: How could I damage the RAM slot?

• ahmham

  Hello! which processor is better (intal 84 pentium 4 531 sl9gb philippines 3/00 ghz/1m/800/04a 7635B077)? or (Inte(r) Core(tm) 2 Duo CPU E4500 2.20GHz/2/20 GHz)&?

• CyMax

  Hello. I had 2 2GB sticks. And I bought 4GB and installed it instead of one of the brackets. And in the system properties they write 6GB, but as before it was written in parentheses that 3.25 is available. I have a seven x64. Maternal Foxconn board G31MV. Can you tell me why the quantity was not mentioned? available memory, because the total amount of memory has increased???

• Oleg

• Anton

  Good evening
  Lenovo z570 laptop
  stood operating board for 4GB, added another one in the slot above the first for 2GB. It is from the same laptop (z570) only weaker in terms of video and RAM.
  In the “system” tab it is displayed that there is 6GB of memory, but only 2.92GB is available
  What to believe?

• Anton

• Konstantin

  I can’t find the second memory slot of the Futjitsu Siemens Amilo 3540 laptop - I found one - it costs 1 GB of RAM, it is located above the video chip, but where is the second question. Properties and Aida show two slots of 1 GB each.

• Nikolay

  Good afternoon. Tell me, I have 2 2 GB sticks installed in my computer (motherboard msi board h55me23), motherboard supports 8GB of RAM. I bought myself a Kingston DDR3 8Gb pc-10600 (KVR1333D3N9/8G) with it the computer turns on and after start screen reboots. I changed it to Kingston DDR3 8Gb (2x4Gb) 1333MHz pc-10600 (KVR13N9S8K2/8), with the second RAM the computer turns on, but after the Windows icon appears a blue screen appears and the computer reboots again! the actual question is: is the problem in the RAM? intel processor i3-540(supports 16GB)

• Albert

  Lenovo laptop z565 there are two sticks of 2 GB each, dear ones, if there are two sticks the screen doesn’t flash, but when I remove the second stick everything works, I tried swapping them, it’s useless
  Could there be a problem in the socket or is it software?
  I can’t reset the BIOS because the battery is rolled up and cannot be pulled out

• Oleg

  I can’t find a solution to the problem: at work I squeezed out 4 GB of RAM, I also had 4 GB, according to the parameters they are the same, I have two computers at once, it loads on the BIOS splash screen for about 40-45 seconds, then everything is according to plan, all you have to do is pull out one of strips (leave 4 GB) everything falls into place (BIOS screensaver 3-5 seconds) who can tell me what?

• Azo

  Hello, I have 4 slots for RAM in my laptop, grouped by 2. Initially there were 4 and 2 GB sticks in the two bottom slots, I decided to add 2 more. In general, all the sticks are working, the problem is that if you plug it into any of the top slots The laptop's RAM turns on, but the screen is black and that's it. If you just stick it into the lower ones, then everything is fine.

• Sinister615

  Hello, I encountered this problem, there were two sticks of RAM, one for 1 GB and the other for 2 GB, both slots are the same color, the RAM frequency is 1333 MHz, my processor and the motherboard support the ones I bought. The problem is that when installing new RAM in two slots, the keyboard stops working and writes on the screen to go into the BIOS and change the parameters, but if I install only one RAM strip, the keyboard works, I go into the BIOS, set everything to auto, apply the parameters and it displays two choices: either run Windows according to the standard or with some kind of cleaning (recommended) (I don’t remember exactly) in general, when choosing the recommended choice, a blue screen with an error (driver error), if standard download then the reboot will be constant and again there will be two choices of download options. The processor and motherboard support up to 16GB of RAM, I add only 8... both sticks are the same 1333 MHz.

• Alexander

  Hello. Help needed: on maternal ASUS board P7P55-M? with processor Intel Core i5 CPU 750 2.67GHz (4 CPUs), there were two DDR3 1333 MHz 2 GB sticks (from the same manufacturer, in slots A1 B1), I installed another DDR3 1333 MHz 2 GB stick (from a different manufacturer, in slot A2) - the computer after a while The timer turns off and (after 10 seconds) it starts up. I don’t understand - is it a problem with the RAM (in the stick itself) or did you insert it into the wrong slot?... Thank you in advance for your answer.

• Anton

  I did as you said, I didn’t remove the static, I walked on the carpet in woolen socks, ha-ha, and then lightning struck the switched-off computer by hand... and for some reason it doesn’t turn on.
  I haven't touched it for a week, honestly

• Vadim

  I added DDR3 4G to the laptop, it became 8G. And everything was fine, he sees it working perfectly, but suddenly he began to reboot and there were stripes on the screen and everything froze, he had to force a reboot. Tell me, please, what's the matter?

• Dmitriy

  Hello. I have a GA-P55A-UD3 motherboard with Kingston khx1600c9ad3k2/4 memory/ I installed two more hx324c11t3k4 sticks and Windows stopped loading. The BIOS runs fine, but Windows doesn't go beyond the boot screen. If I take out the new strips, the system boots without problems. What should I do?

• Valery

  I have this question: the computer has oper. 4GB memory, and I found two 1GB sticks in an old computer. Is it possible to install them in new computer yuter?

• Smokeroster

• quantum

• Wolfwood

  Good afternoon. I have a laptop ASUS K40IJ, Windows 7. RAM type DDR2-800 (PC2-6400) 2048 MB and bought another 2 GB.. added to the note, but why doesn’t it show only 4 GB? I bought memory KVR800D2S6/2G (2GB PC2-6400 CL6 200-Pin SODIMM)

• Wolfwood

• Paul

  Hello. The Asus laptop has 2 GB of soldered RAM. There is also a memory slot. I set it to 4 GB. turned it on and checked it shows 6 GB. but after 10 minutes the screen went out. After several reboots, the screen sometimes lights up but goes out after a few minutes of operation, although the beech works.

• Elena

  Help me please. The computer reboots on its own. The cham turns off and then turns on. I took it to the service center. They ran some tests and said everything was fine. Connected via UPS. Replaced a new battery. The problem has not gone away. I bought an additional stabilizer. The stabilizer crackles very loudly periodically and shows increased voltage. Although the electricians said that everything was normal. Thanks to the stabilizer, the computer reboots even more often. I haven't been able to solve this problem for six months. Thank you.

• Krecer

  Help me please. I installed RAM, the computer started beeping, 1 long signal, 2 short ones, I found what the problem was and found a solution, but nothing worked, tell me what to do. Thank you in advance.

• swolond

  Hello! I've been trying to solve the problem with the new RAM for the second day. I've already looked through a bunch of similar topics on the forums, but I can't find a solution to my problem. Let me explain in more detail:
  I have an ASUS M4A785T-M motherboard, which, according to the manufacturer's description, supports 4 x DIMM memory, up to 16 GB, DDR3 1800(O.C.)/1600(O.C.)/1333/1066 ECC, Non-ECC, Un-buffered.
  Operating system - Win 7, x64
  Now I have 2 DDR3 sticks of 2 Gb 667 MHz (PC3-10700H).
  I bought 4 DDR3 sticks: 4 Gb 2Rx4 PC3-12800H 1600 MHz from the same manufacturer.
  And the problems began:
  1. When I tried to install them, the computer did not turn on (the coolers were noisy, did not make any sounds, the screen was black), even after a lot of manipulations with rearranging different boards into different connectors. I updated the BIOS, the computer saw 2 new RAMs (for some reason the BIOS version itself has not changed).
  2. Now the computer turns on with any two new RAMs. With four - it doesn’t work, with three - I didn’t set it. Changing RAM in pairs, I checked their functionality using the Windows service; no errors were found until the end of the check, but after a reboot the report for some reason is not displayed.
  3. Next I tried to play on at least two new boards. I launch the tanks, enter the battle and almost immediately a blue screen appears with the error MEMORY_MANAGEMENT 0X0000001A. I swapped the RAM, installed the other two - the same result: it crashes, only the game time changes with some - after 3 seconds, with others - after 20 seconds. While I’m standing in the hangar, everything works, but it only starts crashing when loading the battle itself, i.e. when the video camera gets involved.
  4. I put the old ones back - everything works fine.
  Returning new RAMs back to the store is not an option. Surely 4 strips cannot be defective?
  Tell me, please, what's the matter? What else can be done to normal operation?

• Savva

  Hello, why, after installing additional RAM and cleaning the computer from dust, does the computer start up until the “energy” message is displayed and nothing else happens?

• Aidar

• Konstantin

  Please tell me. There are two 1 GB sticks, I want to add another 2 GB, the system supports it, there are two free slots. Which is better: one 2 GB, or two 1 GB? Thank you.

• LeONE

  I have 4 places 2 for ddr2 and 2 for ddr3. Only 1 ddr3 (2GB) is installed, can I add another ddr3 for 2GB? Or is it better to buy one ddr3 for 4GB, there is no difference!

• Shurik

  Please tell me. I installed an additional 4GB of RAM on the laptop: DDR3, 1600MHz, 12800, in general, everything is the same as on the preinstalled RAM. As a result, 8GB. CPUz - sees everything - both boards. But I enter the game and it slows down. Previously went to best settings and slowed down less. What could happen, besides the fact that maybe a defective board was found? Thank you!

• ♕-SlawkA-♕

  Hi all! I have this problem.
  On my mother there are 2 slots for RAM sticks and there are two 2GB sticks. And somehow I installed one 2GB stick on another PC. When I turned on that PC, it started beeping, I turned it off and pulled out my bracket. Then I came home, put the bar back in, turn it on, turn on my PC itself, it starts, BUT it doesn’t go any further than turning on the monitor screen. That is, the PC makes noise, but does not turn on. Whatever I did, when I pulled out the bar, it started at 2GB. As soon as I put the original second bar back, there is silence on the screen again. I can’t even go into the BIOS or go anywhere. Please tell me, is this already a kirdyk bar itself? Or is there some way to revive her? There is no second PC where I could check. Unfortunately.

• Julia

  Hello. The question is: in the Asus x73s laptop, a second 4GB RAM was installed in the second slot. After which the space on hard drive C began to change strangely: after a reboot or power on/off it shows different meanings- either 1.5 GB is free, then 7 GB at once. The laptop was checked for viruses, extra files, including temporary ones, were deleted. Please tell me what could be the reason. Thank you.

• Julia

• Julia

• Deslorator

  Hello, I currently have 3 1GB sticks. Two strips are the same, and the third is from a different manufacturer, but the frequency is the same. I bought one more. Now there are 3 from one manufacturer and 1 from another, but the monitor does not light up. What to do in this case

• alex

  Hello.
  After connecting 2 OP boards to the laptop, the laptop stopped turning on. When we inserted the old DDR back, the problem did not disappear. When the memory was changed (the battery was not removed), could this cause the motherboard to burn out?

• Yuri

  Hello. I have a P5G41T-M LX motherboard, I bought DDD3 Kingston KVR13N9S6/2. I installed it, the computer turns on a black screen and that’s it. Tell me, maybe this DDR is not suitable.

• Yuri

• Yuri

  The result is that the connectors and old sticks work, it’s just that this motherboard doesn’t see the new DDR3 models, I checked 2 different 4gb sticks and this 2gb kingston and all 3 new ones don’t see.