Menu
homePhoto and video

Asus rt n12 login and password. Connecting the ASUS RT-N12 VP B1 router to a computer. Configuring the Asus RT-N12 router with L2TP, PPPoE, or PPTP connection types

Those ordering an Internet connection service are faced with the need to organize Asus works RT-N12. Router with Wi-Fi function works according to wireless protocols communications, additionally supporting and wired connection. Modern devices allow you to combine computers, tablets, as well as smartphones, TVs equipped with Smart TV into one network, which provides more convenient use technology.
The Asus RT-N12 router provides simultaneous and fast access to the Internet for any of the above gadgets

This router requires certain settings. It is worth noting that all routers famous brand differ practically same settings, however in different models However, there are various nuances.

The Asus RT-N12 setup instructions will help even a novice user to easily understand the connection features, gaining access to the World Wide Web in a few minutes.

How to connect Asus RT-N12?

Connecting the Asus RT-N12 router to your computer takes just a few minutes. You are required to be careful and attentive.

Then you need to follow these steps:

  1. We connect the wire from the provider to the correct port.
  2. We connect any of the LAN ports located on the modem to the network card computer equipment with help special cable included with the router. It is worth noting that the cable must be correctly connected to the network card connector along with the LAN port.
  3. We screw the antennas to the device.
  4. Turn on the power for the Asus RT-N12 router.

Before setting up Beeline Internet on your computer, make sure that the IPv4 connection properties are as follows:

  • Automatically obtain IP addresses.
  • Obtain DNS server addresses automatically.

If you do not check, there is a high probability that you will encounter problems with the Internet connection provided by the provider. These properties are located in the Network and Sharing Center, which is located in the “Control Panel” section. When you click on “adapter settings”, click on the local network connection icon. Then select properties and go to the IPv4 protocol section. IN this protocol select properties and install required parameters. It is worth noting that some third party utilities are able to change these parameters while performing their functions to optimize the Internet.

It is important not to use the provider's connection, both during the procedure itself and after its completion. Otherwise, the Internet connection will not work properly. The provider connection means the connection used by the user previously, before purchasing the modem.

The next step will enable the connection. Launch an Internet browser and follow the recommendations. This instruction will ensure there are no difficulties when connecting:

  • First of all, enter the modem’s IP address in address bar, looking like this: 192.168.1.1.
  • Then press “Enter”.
  • In the window that appears, the system will prompt you to enter control data that allows you to access the router interface. We register a login and password. It is worth noting that each router of this company is characterized by standard control information, so we enter admin in both fields. After this, you will enter the main page, where the Beeline Internet settings will be directly selected.

On home page Click on the “Internet” section, which is located on the left.

L2TP connection will require filling in connection parameters. In the WAN connection type field, specify L2TP. Then click on “Yes” in the column asking whether to obtain an IP address automatically. We set a similar parameter next to the “Connect to a DNS server automatically” field. Then enter the username. It is worth noting that in this column we indicate the login provided by the provider. The same goes for the password.

  • Save the selected parameters.

It ends. The Internet connection will be established within a minute, and you will be able to log into the network and open any Internet sites.

Setting up Wi-Fi settings

RT-N12 provides the opportunity to get simultaneous Internet access to different gadgets and devices. Setting up the Asus RT-N12 router, in particular this function, requires selecting the following parameters:

  • In the menu, click on the option called “Wireless Network”.
  • In the new window select:
  1. hostname for the Asus RT-N12 router, that is, SSID. The name of the wireless network will be visible to users and will allow them to recognize it in the list available networks. It is worth noting that Russian letters should not be used.
  2. We specify the following as the authentication method: WPA2-Personal.

To create it we use both Latin letters and numbers. The minimum number of characters is eight.

  • Save the settings by clicking on the appropriate option.

After this, the user will be able to connect any device to the wireless network. It is worth noting that if you connect to a router wirelessly, after changing the router operating parameters, the Internet connection will be disconnected. If you encounter such a situation, then rejoin the network by searching for it and entering an access password.

WATCH THE VIDEO

In this article, we suggest that you familiarize yourself with the instructions for setting up an Asus router by logging into the admin panel of the router using the data provided for this.

Routers from manufacturer Asus some of the most popular and widespread in our country, especially the models: RT-AC51U, RT-AC68U, RT-N12, RT-N16, RT-N11P, RT-AC3200, RT-N14U, RT-N66U, RT-AC87U, RT -AC66U, RT-N56U, RT-N56U. The process of setting them up is not much different from setting up equipment produced under other brands, but there are still differences. Therefore we decided to create separate instructions for Asus routers.

We configure Asus equipment as standard:

  1. We connect to the router using a network cable or via a Wi-Fi network.
  2. Using any browser, go to the control panel.

Please note that you can enter the settings and change them not only from a desktop PC, but also from any mobile device: tablet, smartphone. However, it is more convenient to do this using a desktop PC or laptop. In this case, it is better that the device is connected via a cable, but if you use demon wired connection, then keep in mind that you should not update the router’s firmware using Wi-Fi, because There is a high probability of receiving non-working equipment instead of a working device.

Entering the Asus router settings - 2 connection methods

  • If there is an existing connection between the router and the computer, this instruction page You can scroll below, as we will start with the connection process.
  • If you do not have a connection, you must establish it in one of two ways: through network cable or WiFi compound. Let's look at both options in more detail:

Connecting to the router via a network cable (network).

  • Everything is very simple here: we take the cable that comes with the router and connect it to the device using LAN connector. The connectors are labeled and therefore the error here is minimal, since you can choose any of the four (see the figure below). The second end of the cable is inserted into the connector system unit or laptop. This is what it should look like:
  • Now you need to connect power to the router. Should I disconnect the WAN cable that is connected to the device? You don't have to do this this cable It doesn't allow me to make the correct settings.

Connecting to a router via Wi-Fi

If you have previously set up a connection to an Asus router, then this will not be a problem for you. In the case of a new router, immediately after turning it on, it will start looking for a wireless network, which in most cases will be called Asus.

The network will be without a password, and you just need to join it by clicking on the network and selecting “ Connect“:

How to enter the settings of an ASUS router if you have forgotten your Wi-Fi password?

If you don’t remember the Wi-Fi password and there is no way to find it out using other connected devices, then you will have to use a wired connection. If there is no cable, then you can do this: reset all the router settings to factory settings and set the settings again. To reset your ASUS device to factory settings, you need to press and hold 10 Seconds button RESET.

Login to ASUS admin at 192.168.1.1

  • After connecting, you need to open any browser in the address bar and enter the address: 192.168.1.1 . Go to this address. If you are setting up this router for the first time, a page will open where the settings are displayed. Find the wizard in these settings quick setup Asus devices. Are you prompted for a password and login? Use standard ones, for example, login - admin and password - admin.
  • Of course, if you previously changed your password and login, then enter yours. If the password and login have been changed, but now you cannot remember them, then you need to reset the settings to factory settings, as described above.

Where can I get the address that is written in the browser address bar to access the settings? It is indicated on the body of the router itself. Here:

Don `t come in in the router settings? What to do?

The answer to this question depends on what kind of error you have and at what stage of the process. Some users encounter problems connecting to the router; for many, settings in one browser or another do not open and the message “ the page is not available“. These are the most common problems and to fix them you can try the following:

  1. Check the IP receiving settings if you are using a local network or Wi-Fi.
  2. Check the IP network settings for the presence automatic receipt addresses, but the problem persists, then try using a network cable.
  3. If the connection was initially made via a cable, then you need to check that it is connected correctly.
  4. Make sure the router is connected to the mains (the red light should be blinking).
  5. Try accessing the settings from another device using a cable and Wi-Fi.
  6. Reset your router to factory settings and try the connection procedure again.

Step-by-step setup of RT-N12 C1 (B1, D1) for any provider: MTS, Beeline, Rostelecom and TTK, also Dom.ru. Indicates how to properly install a VPN server. And the result of three tests is given.

ASUS routers called RT-N12 are presented in three models: B1, C1 and D1. New firmware with a black interface is installed on the D1 router, and for C1 it is easy to update. Model B1, in turn, simply cannot be purchased. That is, for C1 and D1 the setting looks the same, and there are also HP B1 and VP models that have the same black interface. This is what we will talk about further – it’s interesting to configure the ASUS RT N12 in a new version. Your firmware number must start with a three.

Equipment and appearance

Appearance of the device

The ASUS website lists the following equipment: power cord LAN, router, power supply, two antennas and warranty card. For models B1 and C1 there is also a CD-ROM, and their power supply produces 9 Volts. And for D1 you need 12 Volts! The current strength is 1 Ampere in the first case and 0.5 in the second.

Specifications

Each of the three routers under consideration is built on the same processor. The amount of memory and ROM is also the same:

  • Processor – BCM5357, 300 MHz;
  • FLASH – 8 MB;
  • RAM – 32 MB;
  • Wi Fi – 802.11n, 300 Mbit/s.

It does not follow from the above that the firmware from routers of one revision is suitable for others. Whoever forgets about this will receive a “brick”.

The hardware revision number is printed on the label in top line. Example: “H/W Ver. B1".

Options and functionality

3 modes, 4 networks

Each of the three devices, from B1 to D1, operates in router, access point or wireless repeater mode. You can create not one, but four WiFi networks, endowed different names. And can be adjusted throughput each of the networks. In reality we're talking about about the same network, it’s just that all subscribers will see four SSID names, and depending on their choice they will receive different traffic. Well, the speed of “300 megabits” is, of course, a theory.

All characteristics are summarized in the table.

ParameterB1C1D1
Case dimensions, mm179 x 119 x 37190 x 125 x 37179 x 128 x 28
Ports4LAN + WAN, 100 Mbit/sSameSame
Ability to configure LAN as WAN+ + +
VPNIPSec, PPTP, L2TP, PPTP server*IPSec, PPTP, L2TP, PPTP server
WPS button+ + +
Mode selector (router, etc.)TumblrTumblrProgram

Quick Setup Wizard

The asterisk means “only after updating the firmware to version 3.X.” Further, LAN as WAN is configured normally in the third firmware, but not in beta. But for B1 it still needs to be found. However, in the “old interface” they do this: select the IPTV STB port, and use it as a WAN. This method has a drawback - the WAN indicator on the router will not light up.

Work in the "master"

When you first connect to a PC, the router turns on the “master”, and all you need to do is go to the website “192.168.1.1”. No password is needed. Click “Go”, set a password and click “Next”. Then the router will configure itself WAN connection. But reviews say that this option does not work for everyone.

Most likely, the connection type will have to be set manually. " Special Requirements» – this includes MAC cloning. The “wizard” will ask for parameters, and you must fill out the fields correctly. “Router settings” is the third section where you set the password for the WiFi network.

Indicators and connectors

When designing its routers, ASUS did not invent anything. On the case of the RT-N12 router there are 7 LEDs indicating the presence of voltage, as well as the activity of 5 ports and WiFi. A short press on the Restore button will reboot the router, and pressing for 5-7 seconds will reset the settings. This is how any ASUS router works!

Rear panel of the router

Yellow ports are home network, and the provider's cord is plugged into the WAN port.

If the WAN port on the router burns out, you can use the LAN port instead of the WAN. Company ASUS- kind, but needs additional configuration.

Video: setting up the Internet, Wi-Fi network on ASUS RT-N12

How to connect Wi-Fi router ASUS RT - N12 to a computer

Preparation

On the computer network card set to "automatic". Port LAN router connected to the PC via a patch cord, and the provider cord must be connected to WAN port. Next, power is supplied to the router: in a minute it will boot, and after 2 minutes the computer will update the address of its card. And you can open the site “192.168.1.1”. In the “wizard”, click “Go”, set a password, click “Next”, “Next”. The router will display the Network Map tab.

WAN setup

To set up an Internet connection, open the “Internet” -> “Connection” tab in the router interface. By default, the router is configured in Auto IP mode. For subsequent logins, the admin login is suitable, and the password will be the one that was set. If something doesn’t work out, the router settings are reset: a minute after turning it on, press Restore for 7 seconds.

Setting up the ASUS RT N12 router for Rostelecom

Rostelecom uses different cables– Ethernet, telephone or optical. In the latter cases, you need to know what the VPI and VCI parameters are equal to. And the WAN port of the router must be connected to the modem, where the VPI/VCI numbers are already set. There are no these parameters inside the router interface.

PPPoE

Go to the tab for WAN settings. Select a protocol.

PPPoE Rostelecom

You need to specify the parameters:

  1. NAT – “Yes”;
  2. UPnP – “No” for starters. This is how the router works for everyone, and then you can fix it.
  3. Automatic IP address – “Yes”;
  4. DNS automatic – “Yes”;
  5. The name and password are clear from the contract;
  6. Time is better than “0” so that the router does not turn off!
  7. MTU is better than 1450, and if it works, try 1492;
  8. MRU – 1480, etc. (until 1492).

Let the rest be by default. Press the “Apply” button, and the connection appears on the “Network Map”.

The “VPN + DHCP” option can be disabled.

PPPoA

There is no PPPoA support on the RT-N12 router. By opening the “master”, you can make sure that this protocol is missing.

Internet setup

The same will happen with most other routers, including non-ASUS ones. It is not clear why Rostelecom needs PPPoA.

The efficiency of PPPoA compared to PPPoE will be 1% higher. But it’s easy to choose the MTU - always 1500.

Setting up the ASUS RT N12 router for Beeline and MTS

The easiest way would be to configure PPPoE. It is used by MTS. And the L2TP protocol “from Beeline” is now used by all ASUS routers. But with MTS the question is open, although it has the PPTP protocol, with which there are no problems either. We must remember that in addition to PPPoE, MAC cloning on the router is performed for all protocols! A PC with which the Internet was connected is connected to the router, and the “Clone MAC” button on the settings tab is easy to find.

PPPoE

On the “Internet” -> “Connection” tab, select the desired protocol.

There is no need to change anything - the router is almost configured:

  1. NAT – “Yes”;
  2. UPnP – “Yes”;
  3. IP address, DNS auto – “Yes”;
  4. Username and password – see agreement;
  5. Time – “0”;
  6. MTU, MRU – 1492;
  7. “VPN + DHCP” – “Yes”.

The new settings are “applied”, and in the right top corner The Network icon appears. That is, the router connects to the Internet.

Most often, MTS uses the PPTP protocol (see below).

L2TP

The line vpn.internet.beeline.ru is the name of the server for Beeline subscribers. The router has a “VPN server” field for such names, which is located on the “Connection” tab. The L2TP protocol is selected on it.

Options:

  1. NAT – “Yes”;
  2. UPnP – “Yes”;
  3. IP address, DNS auto – “Yes”;
  4. Name – starts with 089, see contract;
  5. Password - from the agreement;
  6. VPN server - see the beginning of the chapter;
  7. “VPN + DHCP” – “Yes”.

After cloning the MAC, click “Apply”. The router will establish a connection in 30-40 seconds.

You can try setting up the router for MTS. Server name – l2tp.e66.ru or l2tp.local (depending on the region).

PPTP

We are talking about the MTS provider. On the router, set the server name or one of the addresses:

  1. 172.19.1.1;
  2. 172.19.1.27;
  3. 172.19.1.26;
  4. 172.19.1.21.

IN different regions numbers may vary. And the name is vpn.local.

By setting the address in the settings, you make life easier for the router, but not for yourself. On the “Connection” tab, the setup is almost done - just set the protocol.

The main parameters for the router are login and password, server name or address, and nothing more. You need to clone the MAC, click “Apply” and wait 10 seconds.

Setting up a router for Dom.ru and TTK

The Dom.ru provider always checks the MAC address, even on the PPPoE protocol. And TTK does the same, but only using the PPTP protocol. This means that the WAN port of the router must receive a suitable MAC address. For this purpose, there is a “Clone” button.

PPPoE

For TTK and Dom.ru, the setting differs in “cloning”.

PPPoE TTK and Dom.ru

Only login and password are specified. All this is done on the “Connection” tab. The settings need to be “Apply”, and the router connects to the Internet.

Before applying the settings, clone the MAC (for Dom.ru).

L2TP

On the “Connection” tab, select “L2TP”.

  1. Fill out the password and login field (271XXXX);
  2. The router needs to know the server name (one);
  3. Other settings are default.

Click “Apply”. After 30 seconds, the router will create a valid connection.

The names of TTK servers depend on the region: l2tp.svg.ttkdv.ru, l2tp.kms.ttkdv.ru, etc.

PPTP

Both TTK and Dom.ru like to issue a static IP for the PPTP protocol.

Setting up a router will be difficult. On the “Connection” tab, select PPTP, then install:

  1. Your own IP, mask and gateway (see contract). Example for TTK: 10.10.3.200, 255…0, 10.10.3.1.
  2. DNS (both);
  3. Login and password;
  4. Server IP address. Example: 10.10.3.1, 10.10.3.36 – only one.

Clone the MAC and click Apply.

The contract contains 8 parameters! Or 7 if the server and gateway are the same.

Setting up the ASUS RT-N12 D1 PPPoE wireless router

How to set up WiFi on the ASUS RT N12 router?

You can make changes on the start tab. Change SSID, set password.

"Network map"

The router also has a special tab with settings. Its name is “Wireless Network” -> “General”.

It is better to write down all data.

WiFi, shared

The settings themselves are set like this:

  1. Name – any;
  2. Hide – “No”;
  3. Mode – N;
  4. Width – “40” (300 Mbps) or “20” (150), but not “Auto”;
  5. Router channels (I and II) – both “Auto”;
  6. Method – WPA2 or WPA for older Android devices;
  7. Encryption – AES or TPIK for WPA;
  8. Key – 8 characters.

Click “Apply”. The router will reboot.

ASUS RT N12 IPTV setup

All settings are contained on the “ The local network» –> «IPTV».

Select a name for the Internet connection. Then:

  • Select a port for the set-top box (does not work with the Internet via ADSL);
  • For a PC or Smart TV, you need to “Enable” the last two options.

Click “Apply”.

The router will not transmit traffic intended for the set-top box to the local area.

ASUS RT - N12 VPN server setup

The router can be a server.

VPN server

To configure, open the “VPN” tab:

  1. “Server”, “Enable” – “Yes”;
  2. “More details”: “LAN to VPN”, MPPE, IP pool;
  3. “Server”: “+Add” and password with login.

After each step, click “Apply”. The router is designed for 10 subscribers.

When the router was a PPTP subscriber, it used MTU/MRU = 1450.

Local LAN and DHCP

On the “Local network” -> “IP address” tab, set the router address.

The DHCP Server tab contains other settings:

  1. Router name in LAN;
  2. Auto-issuing address pool (for PlayStation set X.9-X.254);
  3. Gateway address, by default equal to the router address.

It is better not to turn off the server. The main thing is to click “Apply”.

IP values ​​in LAN networks and WAN should not intersect!

How to reset your router?

Two equivalent methods:

  • Turn on the router, wait a minute, press Restore for 7 seconds;
  • Select “Administration” -> “Manage Settings”, click “Restore”.

The router will forget the settings. Then it behaves like new.

The photo shows “method 2”.

If you have forgotten your password, do as stated above.

Protecting the settings of the Asus RT-N12 router

All settings are saved on the PC. You need the "Manage Settings" tab.

Administration

The latter is needed to download the settings to the router.

Update to the latest firmware

You can download the firmware on one page:

  • B1: www.asus.com/ru/Networking/RTN12_ B1/HelpDesk_Download/;
  • C1 and D1: change the letter B to C or D.

The ASUS instructions do not contain this information. Then on the router go to the “Update...” tab.

Firmware

Select a file and click “Submit”.

After pressing, you have to wait 5 minutes. And the router cannot be turned off!

Tests

WAN-LAN transmission speed is almost 95 Mbit/s.

Testing

  1. WiFi 20 MHz – 21 and 16 (some have 52);
  2. WiFi 40 MHz – 40 and 30 (90).

The router also coped with L2TP. The result was slightly higher than 70 Mbit/s.

The main advantage of RT-N12 is its affordable price.

Video about ASUS RT-N12: connection and setup

ASUS RT-N12 is a very popular device, which is classified as budget options. Everything is present in it required characteristics for the successful work of ordinary home, public or work network. The device is a portable Wi-Fi access point, which has an information transfer speed of up to 150 megabits per second (possible Internet speed). The operating frequency of this device is 2.4 GHz. According to the standard, it has 4 network (regular cable) ports; these are standard characteristics for the ASUS RT router, which are needed for direct connection to a desktop computer.

Overview of all bulbs and connectors

The front part contains 7 indicators that will let you know the state of the device at this moment.

Number 1 we have identified the most important led indicator. This is the power indicator. The indicator can have several configurations:

  1. The light is off. This means that there is no power, or the device is simply turned off.
  2. The light flashes with a large amplitude. This means that the router is just starting up.
  3. The light flashes with a small amplitude, quickly. This means automation is happening.
  4. The light stays on without blinking. This means that the system is loaded and can be used.

Number 2 we have identified an indicator that determines Wi-Fi status ASUS RT N12 D1 router on this moment. It has three configurations:

1. The light is not on. There is no power or wireless mode may be disabled.

2. The light flashes. This means that information is being transferred.

3. The light just stays on. The device is ready to transmit data, but no packets are being exchanged at the moment.

Number 3 we have designated an indicator that determines whether the router is connected to Internet networks. There are only two configurations:

1. Off – no internet. This may be due to non-payment, due to communication problems, or due to disconnection from the Internet in equipment installations.

2. Lights up – everything should work properly.

Numbers 4-7 indicators of the status of local ports are indicated. Each has three configurations:

1. Off – the cord is disconnected.

2. Light flashes – information is being exchanged.

3. The light just lights up - this is a sign that the port is occupied by the cable connecting the PC to the network.

The rear panel contains connectors and switches. There are no indicators on it.

1. WPS button (starting from the right side), which is used to quick login to the network.

2. WAN port, it is designed to connect the Internet cable to the router.

3. Four network ports, which are needed to directly connect the PC to the router via cables.

4. Micro connector for power cord.

5. On/off key.

6. Reset key. It is inside the hole; press it for seven seconds to reset to factory settings. The factory settings are standard password and login.

How to install a router

Installing a router is not difficult and will not take much time. Connection and setup takes longer. First, you should check the availability of all components so that the installation takes place correctly:

· The router itself.

· Power unit.

· Internet cable, which must be provided by the company or provider.

· For the first installation, you need to use a local (direct) Internet connection so that there is no interference.

Once you have found everything you need, you can proceed with a fairly simple installation. First you need to figure out how to connect the Internet to the router using an Internet cord. We designated the connector for this cable with the number 2. Then you need to connect using a LAN cable. All that remains is to connect the router to power by inserting one end of the power cord into a power supply with a voltage of 220 Watts, and the other end into connector number 4. Then press the power button. We act in exactly this order.

Installation, as you can see, is not difficult. After these steps, the router should start up. This completes the installation of the router; further debugging is done using a specific page built into the router.

Setting up ASUS RT-N12

To configure the router you need any browser. Enter “192.168.0.1” or “192.168.1.1” as the site address - without quotes.

Attention! The PC or laptop must be connected to the router, and not to the Internet cable.

After going to the page, a window with data entry fields will appear.

Here you need to enter a user name and password. When the router is just purchased, the default login and password are the same – “admin”. After complete debugging, it is recommended to change both the username and password to eliminate the possibility of hacking.

There are times when the router has already been used before, then the name and password sometimes differ from the standard ones. In order to fix the ASUS RT N12 device, the firmware is returned to its original state. To do this, you need to hold down the key, which was designated above as number 6. You need to hold it down with some thin object, the easiest way is a paper clip. Hold the key for 7 seconds. After this, all changed router settings will return to their initial state.

If these manipulations do not help, the router does not return to standard settings, then the adjustment must be performed by a specialist whose range of work includes ASUS firmware RT N12. You can handle this task yourself, but the router firmware is not standard situation For regular user. Reflashing a router is much more difficult.

Connecting to the Internet with full setup

In order to connect the Internet to the router, on the website that opens, you need to go to the router settings. Then - " additional settings" Select the “WAN” item we need (this is setting up an Internet connection).

In the main settings you need to set the following data:

· WAN connection type – select here PPPoE (the most popular) or for Beeline L2TP (you need to check with your provider).

· Enable WAN – our choice is “yes”.

· Enable NAT – our choice is “yes”.

· Enable UPnP – our choice is “yes”.

In the next window, called setting up a WAN IP address, opposite the line we need, “Obtain a WAN IP address automatically,” we must mark the answer as “yes.”

DNS Settings WAN, similar to the items that came earlier, opposite “Connect to the DNS server automatically” you need to select the option “yes”.

In the username field, as you might have guessed, you need to enter your number or login, which is provided by your Internet provider to log into the Internet.

The password is identical.

Some fields are allowed to be skipped. IN VPN server enter the one provided by your Internet provider. If you are setting up an ASUS RT N12 router for beeline, then this is “tp.internet.beeline.ru”; for Rostelecom you do not need to mark anything.

After this entire procedure, click on the “Apply” button. This completes the configuration of the Internet on the router.

Connecting to the Internet using quick setup

Fast ASUS setup RT N12 can significantly reduce the time required for full customization router. On the main page of the router, press the “Go” or “Go” button.

The router then automatically detects your connection type. Even though he himself will determine required parameters, but the login and password for the Internet will still need to be entered manually in the WiFi settings.

Setting up wireless mode

Set up ASUS RT N12 in wifi mode can be done quite simply thanks to the “quick setup”. The final stage of quick setup is debugging the wireless network parameters. Here you can set the SSID and network key or password.

They also perform setup in manual mode. Here we go to the “Wireless Network” window, we only need to set a few parameters. Among them:

· “SSID” is the name for detecting your ASUS RT N12 Wi-Fi router. Prescribe with Latin letters(English).

· The “Authentication Method” field – here we definitely highlight WPA2-Personal, it will help protect your Internet from unwanted users.

· “WPA Pre-Shared Key” – the key or password for your Wi-Fi. Enter when connected to Wi-Fi. Enter the key no shorter than eight characters.

Now you can save the settings. Right now WiFi setup ASUS RT N12 router is absolutely complete. You can connect all the devices that are in the apartment and use Wi-Fi even on the washing machine.

Small addition

How to perform port forwarding? We'll tell you how to open ports on the ASUS RT N12 C1 router, the setup is quick here. Since this is just an add-on, the instructions will be very condensed. We proceed according to this scheme:

192.168.1.1 (address) -> Local network tab -> DHCP server window -> Enable manual assignment field - “Yes” -> MAC address (here you need to select the right computer, to which a static address will be assigned) -> Select and apply (after you have selected the desired PC).

If this does not help, then check your antivirus and firewall.

Video on the topic

Happy Internet to you!