Menu
homeTelephone

Tp link login. I can't access the address to configure the router. Possible connection obstacles

Authorization

In order to get to the router’s web interface, you need to open your Internet browser and type 192. 168.0.1 in the address bar, Username - admin, Password – admin(provided that the router has factory settings and its IP has not changed).

Changing the factory password

To ensure that no one but you can enter the router settings, you need to change the password to enter the settings.

To do this, select from the menu on the left System Tools(System Tools) – Password(Password) and enter the settings:

  1. Previous username: old username, enter admin
  2. Previous password: Old Password, enter admin
  3. New username: enter a new username, you can leave admin
  4. New Password: enter New Password
  5. Confirm new password: confirm the new password

Setting up an Internet connection

In the router interface, you need to go to the tab Net(Network), menu WAN(Here you can add, edit and delete connections).

Setting up a PPPoE connection

  1. Select menu on the left Net(Network), further MAC address cloning(MAC Clone)
  2. Click Clone MAC address(Clone MAC address), then Save
  3. In field WAN connection type(WAN Connection Type): PPPoE
  4. Username
  5. Password(Password) and Confirm password(Confirm Password): your password according to the agreement.
  6. WAN connection mode(WAN Connection Mode): Connect automatically(Connect Automatically)
  7. Save. The Internet is set up.

Setting up an L2TP connection

  1. WAN connection type(WAN Connection Type): select L2TP/Russia L2TP
  2. Username(User Name): your login according to the contract
  3. Password
  4. We put a point on Dynamic IP address(Dynamic IP address)
  5. IP Address/Server Name(Server IP Address/Name) - server address or name (specified in the contract)
  6. MTU size(in bytes) (MTU size) - change the value to 1450 or less
  7. Mode WAN connections (WAN connection mode) - Connect automatically(Connect Automatically)
  8. After entering the above settings, click Save(Save). The Internet is set up.

Configuring PPtP (VPN) while automatically obtaining a local IP address (DHCP)

  1. Select menu on the left Net(Network), further MAC address cloning(MAC Clone)
  2. Click Clone MAC address(Clone MAC address), then Save
  3. In field WAN connection type(WAN Connection Type): PPTP
  4. Username(User Name): your login according to the contract
  5. Password(Password): your password according to the agreement. In some firmware, just below it asks to confirm the password (Confirm Password)
  6. Choose Dynamic IP address(Dynamic IP address)
  7. In field IP Address/Server Name(Server IP Address/Name set) - enter the name or IP address of the server. Find out from your provider.
  8. WAN connection mode(WAN connection mode) - Connect automatically(Connect Automatically)
  9. After entering the above settings, click Save(Save). The Internet is set up.

Setting up PPtP (VPN) with a static local IP address

  1. In field WAN connection type(WAN Connection Type): PPTP
  2. Username(User Name): your login according to the contract
  3. Password(Password): your password according to the agreement. In some firmware, just below it asks to confirm the password (Confirm Password)
  4. Choose Static IP address(Static IP address)
  5. In the fields IP address/Server name, IP address, Max subnet, Default gateway, enter the data from the contract. In the DNS field you can enter DNS address Your provider
  6. WAN connection mode(WAN connection mode) - Connect automatically(Connect Automatically)
  7. After entering the above settings, click Save(Save). The Internet is set up.

NAT when automatically obtaining an IP address (DHCP)

  1. Select menu on the left Net(Network), further MAC address cloning(MAC Clone)
  2. Click Clone MAC address(Clone MAC address), then Save
  3. In field WAN connection type(WAN Connection Type): select Dynamic IP(Dynamic IP)
  4. Click Save(Save). The Internet is set up.

Setting up Wi-Fi on the router

Setting it up WiFi connection. IN side menu go to Wireless mode(Wireless). In the window that opens, enter the following settings:

  1. Field Name wireless network (SSID): enter the name of the wireless network
  2. Region(Region): Russia
  3. Channel (Chanel): Auto
  4. Mode: 11bgn mixed
  5. Channel width(Channel Width): Automatic
  6. Enable wireless broadcasting And Enable SSID Broadcast- put a tick
  7. Click the button below Save(Save)

Setting it up Wi-Fi encryption. In the side menu go to Protection Wireless mode (Wireless Security):

  1. Selecting the encryption type WPA-PSK/WPA2-PSK
  2. Version- Automatically
  3. Encryption- AES
  4. PSK Password: enter the password for Wi-Fi network. The password must not be less than 8 characters
  5. Click the Save button at the bottom. After saving the settings, you will be prompted to reboot the router; ignore this requirement (red inscription below).

Saving/restoring router settings

After setting up, it is recommended to save them so that if problems arise, you can restore them. To do this you need to go to the tab System Tools(System Tools) menu Backup copy and recovery(Backup & Restore).

To save current settings router you need to press a button Backup copy(Backup). The settings file will be saved to the specified location on your hard drive.
- To restore settings settings from a file, you must click the file selection button, specify the path to the settings file, then click the button Restore(Restore).

Port forwarding/forwarding

This function automatically redirects requests for certain services from the Internet to the appropriate host of your local network, located behind firewall router. Use this function should be done if you want to create a server on the local network behind the router’s firewall (for example, a Web server or mail server). Let's go to Forwarding (forwarding), press Add (Add New).

IP address - network address device to which the request will be redirected. Service Port and Internal Port- port number that needs to be opened Protocol- Select the required protocol State- On. Click Save.

Determining your Internet provider's network settings

Before connecting the router, you need to know what network settings needed to connect to the Internet.

Most common the following types network settings:

  • Dynamic IP — dynamic settings, are issued automatically via DHCP
  • Static IP — static settings, entered manually
  • PPPoE— Internet access is provided via the PPPoE protocol after entering the username and password

It is assumed that you have Windows 7 installed, the provider cable is connected to the computer and Internet access is configured.

Go to "Change adapter settings".

Click right click mouse on "Local Area Connection" and select "Properties"

Click on “Internet Protocol Version 4 (TCP/IPv4)” and the “Properties” button.

  • If you have selected “Use the following IP address” and there are numbers, then write down all settings- these are the static settings of the provider ( Static IP). After that, select “Obtain an IP address automatically” and click the “OK” button.
  • If you select the “Obtain an IP address automatically” option, then you receive network settings automatically - these are the dynamic settings of the provider via DHCP ( Dynamic IP).

There are providers that block access to the Internet via MAC address(can be found in the contract). In this case, you need to configure the router so that it has the same MAC address that is registered with the provider.

To find out the MAC address of the network card, click “Start”, in the “Search programs and files” window write the command cmd and press Enter.

We write the command in the console ipconfig /all and press Enter.

We are looking for “Ethernet adapter Connection via local network...”

In field " Physical adress"Your MAC address of the network card is indicated. Let's rewrite it.

Connecting and setting up a TP-Link router

For settings Wi-Fi router We will need Tp-Link:

  • provider cable (Triolan, MaxNet, Vega, Volya, Airbites, or others without vpn);
  • computer or laptop;
  • TP-Link router, which will distribute the Internet via Wi-Fi to a laptop, TV with Wi-Fi, tablet or smartphone.

Let's connect the equipment as follows:

  • Plug the power supply into the router’s “Power” connector;
  • connect the Internet provider cable to blue WAN port router;
  • connect the computer to the router using network cable any yellow LAN port;
  • We will connect other devices (laptop, tablet, TV with Wi-Fi, smartphone) via wireless communication Wi-Fi.

Let's move on to setting up the router.

Open Internet browser Explorer and enter the address 192.168.1.1

Attention! The proxy server should not be specified in the browser settings

In the window that appears, enter your username admin and password admin.

On the left side of the menu, select Quick Setup Wizard Quick Setup and press the button Next.

Dynamic IP— automatic network settings of the provider via DHCP

If you receive automatic network settings, then select Dynamic IP and press the button Next.

In field SSID

In chapter Wireless Security specify the encryption type WPA-PSK/WPA2-PSK

In field PSK Password:

Finish.

Network - MAC Clone.

In field WAN MAC Address enter the MAC address.

You can also click Clone MAC Address, if in the field Your PC's MAC Address

Static IP— static network settings of the provider

If network settings need to be entered manually, then select Static IP, press the button Next.

Enter the settings:

  • IP Address(IP address)
  • Subnet Mask(Subnet mask)
  • Default Gateway(Main gate)
  • Primary DNS(Preferred DNS Server)
  • Secondary DNS (Alternative DNS server)
  • and press Next

In field SSID Enter the name of the access point to connect via Wi-Fi.

In chapter Wireless Security select the encryption type WPA-PSK/WPA2-PSK

In field PSK Password: enter the password to access Wi-Fi point access. The password must be at least 8 characters.

The next window indicates that you have successfully completed the setup. Press the button Reboot and wait for the router to reboot.

If your provider blocks access by MAC address, select from the menu on the left Network - MAC Clone.

In field WAN MAC Address enter the MAC address.

You can also click Clone MAC Address, if in the field Your PC's MAC Address the required MAC address is located.

PPPoE— Internet access using user and password

If Internet access is provided via the PPPoE protocol after entering the username and password, then select PPPoE.

Enter the settings:

  • User Name:(Username)
  • Password:(Password)
  • Confirm Password:(Confirm password)
  • and press Next

In field SSID Enter the name of the access point to connect via Wi-Fi.

In chapter Wireless Security select the encryption type WPA-PSK/WPA2-PSK

In field PSK Password: enter the password to access the Wi-Fi access point. The password must be at least 8 characters.

The next window indicates that you have successfully completed the setup.

Press the button Reboot and wait for the router to reboot.

TP-Link router security settings

To prevent anyone other than the administrator from entering the router settings, you need to change the password to enter the settings.

To do this, select from the menu on the left System Tools - Password and enter the settings:

  • Old User Name: old username, enter admin
  • Old Password: old password, enter admin
  • New User Name: enter a new username, you can leave admin
  • New Password: enter a new password
  • Confirm New Password: confirm the new password

After this, press the button Save to save the password.

Connecting a laptop to the Internet

We will connect the laptop to the Internet via Wi-Fi.

To do this, select the wireless network management icon in the lower right corner of the monitor. After updating the list of wireless networks, our network should appear in it. Select it and click the “Connect” button.

On next step enter the password to connect to the Tp-Link router via Wi-Fi.

Enter the password you specified in the field PSK Password: in the router settings. After this, the Internet will appear on the laptop.

You can connect to a Wi-Fi router Tp-Link devices that support Wi-Fi, for example, TV, netbook, tablet, smartphone. To do this, you need to select a point in the device Tp-Link access and enter your password.

Recovering the password to enter the settings of the TP-Link router

If you have forgotten the password to enter the settings of your Tp-Link router, you can restore the factory settings and password.

To do this with reverse side router, press the Reset button for 8-10 seconds.

In this instruction I will show in detail how to configure a TP-Link Wi-Fi router to work with the Aist Internet provider. It is equally suitable for following models routers and their modifications:

  • TP-Link TL-WR740N
  • TP-Link TL-WR741N
  • TP-Link TL-WR841ND

The step-by-step guide describes the following steps: how to properly connect a TP-Link router for subsequent configuration, how to log into the router’s web interface, setting up an Internet connection Stork PPTP, and setting a password for wireless Wi-Fi net.

How to connect a TP-Link router

There are five ports on the back panel of your device, one of which is designated WAN - you need to connect the Stork Internet cable to it.

Connect one of the ports marked with numbers using the supplied cable to the network connector of your computer or laptop. At initial setup better use wired connection, this will reduce the number of nuances that may cause difficulties.

In addition, pay attention to the following points:

  1. In the local network connection settings on the computer, the TCP/IP protocol parameters should be set to “Obtain IP automatically” and “Connect to DNS server automatically”.
  2. Your Stork Internet connection must be disconnected during setup, as well as after it (the router will establish the connection itself). If you have the Aist Online program installed on your computer, disable automatic connection to the Internet and disconnect the Stork connection.

Hopefully the router is already plugged in, let's move on to the next step.

How to enter the settings of a TP-Link router

To enter the router settings, launch any Internet browser and enter address bar tplinklogin.net or 192.168.0.1.

After this, you will see a window to enter your password. Standard login and password for TP-Link router- admin. Also, information for entering the settings web interface is available on a sticker on the bottom side of the Wi-Fi router. If for some reason standard password does not fit, you may have changed it during previous setup attempts, in this case you can either try to remember it, or reset TP-Link to factory settings.

As a result, you should influence home page web interface, where all subsequent actions will be performed.

Setting up Internet Stork on TP-Link

First of all, it should be noted that when setting up a router for Stork there is one nuance, namely the need to change the LAN address in the router from 192.168.0.1 to 192.168.1.1 and here’s how to do it.

In the menu on the left, select “Network” - “Local Network” and in the “IP address” field enter 192.168.1.1, and then click “Save”.

After rebooting the device, the connection with it will be lost. Wait a little and go to the TP-Link settings at the new address (enter it in the address bar, if necessary, reconnect to the wireless network if the settings are made via Wi-Fi).

The next step is to configure the Stork PPTP Internet connection in the router’s web interface. To do this, go to the menu item “Network” - “WAN” and fill in the fields as follows:

  • WAN connection type - PPTP/Russia PPTP
  • Username - your login from the Internet Stork
  • Password and password confirmation - your Internet password
  • IP address/Server name - server.avtograd.ru

There is no need to change any other parameters. Click "Save". If everything was done correctly, and the Internet connection in Aist Online is disabled, the router will establish a connection (to see the status change from “Disconnected” to “Connected”, you can simply refresh the page in the browser).

Setting up Wi-Fi on a TP-Link router

The last step is to set up a wireless network and set a password for Wi-Fi, to do this:


This completes the setup of the TP-Link router for Aist, and you can connect from your phone, laptop or tablet to your own wireless network and use the Internet.

TPLINKLOGIN.NET- This standard address, where the entrance to the TP-LINK router is located. To enter the control panel settings, use the login and password “admin-admin”. Go to Personal Area TP-Link router You can also use its IP - 192.168.0.1 or in some models 192.168.1.1. But what if you open http://tplinklogin.net, an error occurs - how to solve it? Let's figure out together how to log into the TP-LINK router.

tplinklogin.net - login to the personal account of the TP-Link router at 192.168.0.1

This instruction connection is universal and suitable for setting up any TP-Link routers - TL-WR740N, TL-WR840N, TL-WR841N, etc.

Friends!
Read this important information- today login to your TP-Link router personal account at " tplinklogin.net» is no longer available due to simple carelessness - the company forgot to pay for the domain, and it went into other hands. The router's web interface is now located either at the address " " or at the IP "192.168.0.1". Login and password for connection remain the same - admin-admin

Let's start, as they say, “from the stove,” and one of the most affordable routers TP-LINK TL-WR741N will help us with this today.


After this, most users open a browser and enter the address http://tplinklogin.net and in 50% of cases they receive an error that it is impossible to log in.


How to configure a computer to log into the TP-Link router using the TPLINKLOGIN.NET administrator address?

The whole point is in incorrectly set Windows settings connecting the PC network card to the router. Therefore, we go to the computer’s network connection settings by next chain: Start - Control Panel - Network and Internet - Network and Sharing Center shared access- Change adapter settings.

Right-click on “Local Area Connection” and open the “Properties - Internet Protocol Version 4” section


Here you need to set it to " Automatic receipt» checkmarks on the IP address and DNS servers— the router will give them to us automatically. Pay attention to the last point - in the event that certain public servers, for example, or 4.4.4.4, then you will not be able to access the address “tplinklogin.net” or “tplinkmodem.net”. Another possible variant— write here, by default it looks like “192.168.0.1”

If you need, then the way to choose network adapter a little different - you need to right-click on “Start”, select “Network Connections” and then open the “Adapter Settings” section.


Save the settings with the “OK” button.

TP-Link login error - 192.168.o.1/192.168.0.l/192.168.1.1

  • Another very popular mistake lies in the user’s carelessness, when instead of the purely digital value “192.168.O.1”, the letter “o” is entered into the address bar instead of “zero”. Of course, go to the control panel by incorrect address will not work.
  • The same applies when the letter “L” is written at the end instead of the number “1”
  • Finally, it is possible that the IP was simply chosen incorrectly - instead of 192.168.0.1 they indicate 192.168.1.1 and vice versa

How to log into the personal account of a TP-Link TPLINKLOGIN.NET router via admin-admin?

We get to the admin panel - there are many menu items for configuring the TP-LINK router, but the easiest way to start is with “Quick setup”.

First you need to select the type of your Internet connection. Rely on auto mode It’s not worth it - it’s better to find a paper contract for the provision of Internet access services and see there all the data necessary for connection. My Internet works in PPPoE mode - that’s what I’ll choose.


Next, set the TP-Link settings for wireless connections. At the initial stage, it is enough to come up with a name for your WiFi networks(SSID) and 8 character password. Select “WPA2-Personal” as the encryption type. The rest can be left as default.

On last step reboot the router.

These steps are enough to log into your TP-Link router’s personal account via the web interface at tplinklogin.net or 192.168.0.1 and configure it to work with the Internet. By the way, you can also use mobile app- a separate article is devoted to this. Start using it, and you can master the rest of the settings by reading other articles on our blog.
Good luck!

TP-link is the most popular company, which produces routers, routers and more network equipment. I myself have been using a device from this manufacturer for many years. Sooner or later the question arises - how to enter the configuration settings of any router from TP-Link.

You never know, you will need to reflash, change the Wi-Fi password or install more detailed settings– type parental controls for your family or blocking by MAC addresses. Everything is done very easily and there is no need to constantly call a specialist, since the device’s interface is simple and intuitive even for housewives. Let's look at all the methods from connecting via wire to connecting via a wireless network from a phone.

HELP! If you have any questions when starting the router or have any difficulties, write about it below in the comments, and I will help you right away.

How to connect a laptop or PC to a router

Take a twisted pair cable. Usually it comes in a box from under the device. Plug one end into the router, into one of LAN connectors ports (have yellow). And the second into the network card of the laptop or computer.

Log in via your laptop directly

If you did everything as in the chapter above, and the connection goes directly from your computer or laptop to the router via cable, then all you have to do is launch your browser and enter the IP or DNS address in the address bar. You can enter the router settings from TP-Link at the following addresses:

  • 192.168.1.1 – on newer models.
  • 192.168.0.1 – on older devices.
  • http://tplinkwifi.net or http://tplinklogin.net are more common addresses for logging into any TP-Link model.
  • Login admin.
  • Password - admin or empty field.
  • If you launch it for the first time, you will be asked to enter a new password for access, and then the setup will begin.
  • If this router was provided by a provider, then the password can be the company name of that provider. If this option does not work, then you need to call the technical support of your Internet provider and ask for the password there.

Standard login information is also located on a label under the router.

The TP-link router menu will differ depending on the firmware and device model.

Login from laptop via WiFi

If the device is new or has a standard configuration, proceed from step 1. If the wireless network is already configured and you can connect to it, start with step 4.

  1. The router should have a WPS button on the back. Or similar Wi-Fi button with wave logo. Hold it for 3 seconds and release.
  2. Next, on your laptop, click on Wi-Fi in the lower right corner and select new available network. If you have already connected to it before, then use your username and password to access the Wi-Fi. If you just started the router, then the password and network name are on the label.
  3. If you connect via WPS technology, then when prompted for a PIN or password, press the WPS button on the router again.
  4. Next, launch the browser and enter one of the options:
    1. 192.168.1.1
    2. 192.168.0.1
    3. http://tplinkwifi.net
    4. http://tplinklogin.net
  5. We enter the authentication data in the admin panel.

From a smartphone or tablet via Wi-Fi

  1. Launch Wi-Fi on Android or iOS.
  2. Find the network and connect. If the router has already been reset to the factory configuration, the name of the wireless network will have the name of the router model.
  3. If you do not see the Wi-Fi network of this device, it means it is not running. To start, press the WPS or Wi-Fi button on the device, and then try again to connect to the wireless network, which should already be available.
  4. The login, password and standard name for the Wi-Fi network are indicated on the label under the router.
  5. Next, launch the browser and enter the IP address of the router. Or you can configure the router through a special software for smartphone.

Program for TP-Link Tether phone

ATTENTION! This program supports only a number of routers: TL-WDR 4300, TL-WDR 3600, Archer C7, TL-WDR3500 Archer C20, TL-WR941ND_V5, TL-WR940N_V2, Archer C9, TL-WR841N V9, Archer C5, TL-WR740N V5, Archer C2 , TL-WR741ND V5, Archer C8, Archer C20i.

  1. After connecting, download the software from Google Play or App Store. To do this in search bar Enter the name of the program without quotes – “TP-Link Tether”. Or you can download from direct links:
    1. For Android OS
    2. For iPhone and iPad
  2. Download and install.
  3. We launch and act according to the instructions for installing the Internet and local network.

Standard IP address does not work

If the standard address of the router is not suitable, then most likely it was changed earlier. This happened to me once - I changed the standard address and forgot which one. But don’t worry, it’s quite easy to recognize.

  1. Launch the console. To do this, press start and enter “CMD” in the search bar. Double click by application.
  2. Enter – ipconfig and press Enter.
  1. Scroll up a little and in the “Default gateway” line you will see the IP to enter the settings.

If the line is empty, then there is a problem in the connection between the two devices. You need to connect directly to the LAN port. If you are already connected directly, check the integrity of the cable. One of the indicators on the router should blink. Should also flash LAN card on a PC or laptop.

Password doesn't work

Forgetting your admin password is quite easy. If you were the one who did the setting, then it’s worth remembering the combination; perhaps you wrote down this data somewhere - try to remember. As was already written earlier, if the setup was done by engineers from the provider, then it’s worth calling tech. support or reset the router to factory configuration.

NOTE! But remember that after the reset, you will have to do the Internet and Wi-Fi settings again. But there’s nothing wrong with that, our portal has everything available instructions according to the settings of all known routers - just enter the model name in the search bar at the top and read the article.


  1. Find it on the back of the device RESET button(it can be combined with WPS). The button may be recessed and look like a small hole, so you will need a paperclip or needle to activate it.
  2. Press it for 10-12 seconds until the router reboots.
  3. After that, use your standard login details.

Doesn't work after resetting to factory settings

This most likely occurs due to the fact that the PC or laptop has a static IP address with a different subnet.

  1. Left click on network connection in tray.

  1. Next, select "Network and Sharing Center."
  2. Now click on the link "Changing an adapter setting."
  3. Right-click on an available and enabled connection and then go to "Properties".


  1. Select the TCPv4 protocol and click "Properties".
  2. IN top margin put automatic detection IP. And in DNS, set the parameters as in the picture above: 8.8.8.8 and 8.8.4.4.
  3. Click "OK", to apply the settings.

Still won't log in

In this case, the router may be broken. First of all, let's call the number technical support TP-Link:

  • +7 495 2285560 – for Moscow and the Moscow region.
  • 8 800 2505560 – you can call from any region Russian Federation, the call is free.
  • +7 495 2285560 – for calls from Belarus.
  • The settings and firmware of routers, modems, and switches can be viewed on the official website.

If telephone numbers are not available, then you can describe your problem in a letter and send it by mail - [email protected].