192.168 1.1 asus personal account. View the router's IP address in a network environment. Can't access your router settings? What to do

The ASUS RT-N10 router is configured like most wireless routers via the web interface. To enter the router settings, you need to connect via wire to one of the four blue ports with a cable and type the site address http://192.168.1.1, then enter the login and password admin. Connecting to the router via Wi-Fi in order to configure it is not recommended by the manufacturer, but in practice it does not cause any particular problems.

How to configure ASUS RT-N10 router

When you turn on the router for the first time, you need to decide on the operating mode of the router. In most cases, and in ours too, this is the mode wireless router. In this mode, you allow the router to distribute the Internet via wires and Wi-Fi in your apartment or office without any signal relay. After selecting the mode, go to the main page (corresponding button below).

The main page of the router displays quite a few parameters, incl. not entirely necessary for a less knowledgeable user. However, the following options are shown here:

Top of the window

• The name of the wireless network (factory name ASUS) is displayed.
• Version software router (firmware).
• Operating mode (Router).
• Interface language (Russian).
• A button to exit the router settings and a button to reboot the router.
• Hover assistant useful tips according to the state of the router. Recommended for use by less knowledgeable users as a hint.

In the side column on the left

• Menu for going to the corresponding sections of the router settings.

In the side column on the right

• Name of the wireless network.
• Password ( network key) from a wireless network.
• Wireless network speed.
• Enable or disable Wi-Fi on the router.
• Internal IP address of the router.
• PIN code - password for quick connection wireless devices with the specified key.
• MAC address of the router (may be needed in provider networks where binding to a device is used).

Centered in the window

• Graphical representation of the status of your Internet connection and connected devices.

By default, the internal IP address of the router is 192.168.1.1. In the Ivstar network there is no need to change this address, so just skip this step. However, there are cases. when the router's IP address needs to be changed to another. To change the IP address of the router, select the LAN IP address option in the column on the right at the very bottom.

In the LAN IP address tab, specify the router address you need. Don't forget to save your settings. Next, you will go to the web interface to configure the router at this address instead of http://192.168.1.1

If necessary, you can also disable the DHCP server on the router or change the range of IP addresses distributed to your computers. Again, it's worth noting that in most cases this is not necessary.

If you need to get from your network where your router is running to another local network that is not on the Internet, you can use static routes. This may be necessary if the server (gateway) through which you connect to other servers on the network is not configured due to various reasons to communicate with other networks. This can happen, say, when two providers have joined networks and, in addition to the main network, also have a peering network. In this case, in order for subscribers of one provider to be able to access the peer-to-peer network of another provider, routing may need to be configured on the router, or, if there is no router, on the computer.

Detailed routing information can be obtained from your provider's support service or on their website.

Let's move on to the most important thing. On the Ivstar provider network, all router setup comes down to one thing - you need to configure Wi-Fi on the router(set the name of the network and set a password so that your neighbor does not use it for free).

To set up Wi-Fi (wireless network), select the section in the left column Additional settings and onwards Wireless network .

On the first tab Are common In the Wi-Fi settings you should change the following values:

• SSID— the name of your wireless network. It is better to specify the name in Latin characters. Give meaningful names, so that you can later remember what your network is called.
• Authentication method, i.e. type of encryption. Try setting the option to WPA2-Personal. If you have problems connecting to Wi-Fi, then select a different type of test, a simpler one.
• Preliminary WPA key , i.e. the password for your Wi-Fi. With the WPA2 verification method, you must enter from 8 to 63 characters.
• TX-power, i.e. the power of the Wi-Fi transmitter as a percentage. The initial value is 100, i.e. 100%. The maximum value is not always justified. if there are often problems with the signal within the apartment or if you plan to connect only within the apartment or very small room, then you can reduce the TX-power value to 25 or less. It is especially important to reduce the power if your router, which you are unlikely to turn off at night, is located not far from where you sleep.
  For the most curious and techies: 100% of the power of this router corresponds to approximately 15-17 dBm of power.

If you don’t want Wi-Fi to work around the clock and don’t want to pull the router out of the socket every time, you can set a Wi-Fi schedule on the router. At the top, go to the Professional tab. In addition, here you can configure other parameters that can help with the router if it is in an area of ​​strong interference or works with very remote client devices. Uninitiated users should not play anything in this section. In the right column, tips will appear for each item, what it is for and what to do with it.

If you do not want other users of your home network or your company’s networks could access the router and change whatever they want, you can set a password to log into the router. In the left column, select the section Additional settings option Administration. Then go to top menu bookmarked System and change your password.

After various changes in the router settings, you will need to save the settings and reboot the router. It is necessary to reboot the router even when it freezes. In the right corner of the router settings there is useful button. The reboot process takes a minute or two.

In the Ivstar network, to connect to the network and the Internet, you do not need to set up any connections and enter passwords and logins - this is all in the past. We use modern technology IPoE (Internet without passwords).

However, the next point is still worth checking. Additional settings In the left column, go to the section and then select the option.

WAN In the Ivstar network, in the Internet connection tab in the field Connection type must be selected.
Dynamic IP, must fill in the MAC address field at the very bottom. It must match the MAC address of the network card of the computer that was connected to the modem before purchasing the router. If the router was initially installed when connecting, then this field does not need to be filled out.

If for some reason the router cannot automatically obtain IP addresses, that is, it cannot operate in Dynamic IP mode, you can resort to a trick by selecting the WAN connection type option Static IP. Address values ​​for configuration can be obtained from technical support.

If you use a login and password when connecting to the Internet (VPN connection), you select the PPTP option in the WAN connection type field. Below in the Settings section account you need to enter your login and internet password. Even lower in the section Special Requirements Internet service provider, you must enter the server address (VPN server) to connect.

If the router managed to establish a connection with the provider’s server, then the Connected status is displayed on the main page of the router next to the globe.

ASUS RT-N10 router firmware

The most important rule. If the router works properly and does not glitch, then there is no need to reflash it (update the firmware version), even using official firmware. Only when you observe very often unstable work router, if it constantly needs to be rebooted or the Internet does not work correctly on it via wires or, conversely, via Wi-Fi, there is a reason to start flashing the ASUS RT-N10 router. If official firmware the router does not help, you can try to reflash the router alternative firmware

. However, be prepared that if something goes wrong, you will have to part with the router and buy a new one.

Photos of the ASUS RT-N10 router

Reverse side of the router On back side router there is a sticker on which the factory login and password for logging into the ASUS-RT-N10 router, the name of the router model, the router firmware version are indicated, serial number

and a PIN code for quickly connecting to the router via Wi-Fi using WPS.

ASUS RT-N10 router processor (chipset) - Ralink RT3050F.

The RT3050 chip has a 1T1R architecture (one receiver and one transmitter), which allows it to achieve a data exchange rate of 150 Mbit/s. Supports up to 256 clients, up to eight BSSID (Basic Service Set Identifiers), technologies WEP security (Wired Equivalent Privacy), 64/128/ WPA (WiFi Protected Access), WPA2 and WPS (WiFi). The configuration includes up to 64 MB of 16/32-bit SDR SDRAM, a 5-port 10/100 Ethernet switch, five 10/100 UTP ports, and one RGMII/MII port (RT3050).

ASUS RT-10N C1 router parameters

Devices from Asus are in wide demand among consumers. That is why we decided to make this article, although the process of entering the settings of the Asus router is almost identical to this process on routers various manufacturers. You can verify this by looking at our website for instructions on how to enter the settings of routers from other manufacturers or

Access to the router settings is carried out according to the traditional scheme:

1. We connect to the device (computer, laptop) using a network cable or via wi-fi connection;
2. through any convenient browser We log into the control panel of the router.

To establish a reliable connection with the router, it is best to use a computer or laptop and a network cable. Although, of course, you can use other devices (tablet, phone) to access the router settings and make changes to them. We strongly do not recommend using a Wi-Fi connection to flash the router firmware or install a software update. With a Wi-Fi connection, there is a very high probability of failures and unpleasant consequences of changing the router software.

Have you already connected the router to your device (computer, laptop)? If yes, then go to next step. And if not, then let's see together how to connect to an Asus router. We will use the connection via network cable(because it is the most reliable).

We take out the cable from the kit to the router and insert one end into the connector labeled LAN router, and the other end into your PC or laptop. There is also a WAN connector on the router; do not try to insert the cable into it. If a cable is already connected to the WAN connector, then you don’t have to disconnect it, it will not affect our process. Make sure that the router is powered on, pay attention to the indicator on the case.

Connecting to an Asus router via wi-fi connection is quite simple. If you have never done this before, it will be useful to first familiarize yourself with this article. New router When you first start it will immediately broadcast the wireless network. By default, the name of this network is “ASUS”, but there is no password. To connect to wi-fi networks Just select its name and click the “Connect” button on your computer.

Go to the router web interface

In the router authorization window, by default, the login is “admin” and the password is “admin”. This information can be read on the label at the bottom of the router case. If for some reason you do not know the password (it was previously changed by someone, it may have been successfully forgotten by you), and the standard ones do not work, you need to reset the router settings. To reset the router settings, press and hold the RESET button for 10 seconds, the button is located on the router body.
Problems accessing the router control panel and how to solve them.

When trying to connect to the router control panel, users sometimes experience problems at various stages of operation. Some people are unable to establish a connection between the router and the device, while others cannot open the page itself in the browser. There is no single recipe for solving all problems that users encounter. Let's look at the main ways to solve problems accessing the router control panel.

First, you need to figure out how to connect the router to the device. For this you need check whether you receive an IP when connected via cable or Wi-Fi connection. If automatic IP acquisition is set, check if everything is okay with the cable itself (try unplugging it from the connectors and reinserting it, replace it with another cable) or check the connection via Wi-Fi connection. Sometimes the problem lies in simply turning off the power to the router; look at the indicator on the case. If you are unable to connect via cable to the router, then try doing it by wi-fi connection. And if you tried to connect via a wi-fi connection, then try, on the contrary, using a cable.

If the problem is not solved after the above manipulations, then perhaps one of the methods from the article ““ will help you. You can try connecting to the router from another device. Another way is to reset the settings on the router. After that, try going to 192.168.1.1 again. Try using .

You can write about all your problems connecting to the Asus router control panel in the comments below. We'll try to figure it out and be sure to help you.

Today we will talk about how to go into the router settings. Sometimes you need to enter the settings, but many people forget how to do this after connecting and configuring the router. In this article I will tell you how to enter various models. If you know how to enter the settings of your router but cannot do it, here is an article that describes. This article is designed for the fact that your router is already connected to the computer (if the router is not connected to the computer, read the article ““). Let's get started with the instructions.

General instructions for entry.

You can enter the settings using any browser. Need to be driven into address bar router address and enter your login and password.

First, let's figure out where to get the router address. On many models, the address is written at the bottom of the label, and the login and password are also indicated there.

If you don’t have a label or don’t have access to it, you can also look in the network card settings.

On Windows XP here>>

On Windows 7 here>>

You can find out more about how to determine the router address.

Once you have determined the address of your router, enter the address into the address bar in your browser and press Enter. An Authorization window will appear in front of you, asking for Login (Username) and Password. On many models, the following settings are set by default: Login - admin, password - admin. Also look carefully at the authorization window; they sometimes write the default login and password, for example, Zyxel company(I'll show you what it looks like below). After entering the data, press “Enter” and go to the settings of your router.

Let's apply this scheme on some models. The main thing that you must understand is that further we will consider the case when the router is already connected and has standard settings entrance. If this is not the case, then the scheme is simple: we determine the address of the router, if we changed the password and login, we remember and enter it. Also, if you couldn’t remember the changes, reset to standard settings (how to do this is described in the article “How to connect a router”), and then simply reconfigure it.

Login to router d link dir 300

This entry method is also suitable for models d link dir 615, d link dir 320, d link dir 620. Enter 192.168.0.1 into the address bar of the browser (go to the router settings d link dsl 2640u can be found at 192.168.1.1). In the window that appears, enter your login and password. If the window looks like the picture below, enter only the login-admin, leaving the password blank. :

Then click on the button. That's it, login is complete.

If, after entering the address, any of these windows opens in front of you:

in this case Name user - admin, password is admin. Click on the “Login” button. And you will immediately be taken to the Dlink configuration interface. If you are interested in setting up a Dlink router, then on the left side of the page in the menu, select the d link section. In it you will find a description of the setup of any model of Dlink companies.

We use this method for asus rt n10

This option is also suitable for routers asus rt n12, asus rt g32, asus rt n10p, asus dsl n10. Open the browser and enter 192.168.1.1 in the address bar. The name is the same as on other routers, the default is admin, the password is the same. See picture below:

Once all fields have been filled in, click the “Submit” button. And you will be taken to the router settings. By selecting the ASUS section in the left column, you will find a description of the settings for various Asus models.

It’s also easy to log into the tp link tl wr741nd router

Also suitable for tp link tl wr841nd, tp link tl wr740n. Let's carry out the same steps as described above. Open the browser and enter 192.168.0.1. In the authorization window we will indicate the login and password admin and admin.

Bottom line

This scheme for entering the router settings is suitable for all models, the most important thing is to find out the login and password that you specified when setting up the router. If you haven't changed anything, then everything remains standard. Also on our website you will find many instructions and settings various models routers.

Video: What to do if you can’t access 192.168.1.1, 192.168.0.1

.

How to connect and configure a router ASUS RT-N12 on one's own? In this instruction I will show you step by step how to install the Internet on it and distribute WiFi signal without disk. For those who have a different model, for example N10U, N14U, N56, N18, don’t worry. This manual Asus setup is universal for any router with latest version interface design in black and blue.

How to connect the ASUS RT-N12 VP router correctly?

First of all, let's see how to connect Asus router to computer. I will not describe this procedure for a long time here. I will just name the main steps:

1. We remove the Internet cable from the computer’s network card and insert it into WAN port on an Asus router
2. Instead, we connect it to the PC Ethernet cable, which was in the box along with the router
3. Insert the other end into the LAN connector

For those who doubt the correctness of their actions, I recommend reading. It describes in more detail the sequence of actions on how to connect the Asus RT-N12 router to a computer with a cable.

In it you will learn how to enter the control panel for configuration and at the same time avoid mistakes.

Computer settings for connecting to the ASUS RT-N12 VP router

Let's move on. Before you actually start setting Asus router, you need to make changes to the configurations of the network card of your computer or laptop. This is necessary in order to be able to access the board panel.

Namely, in the section “Network and Sharing Center - Changing adapter settings”

Here we find either a connection via “Ethernet” or “ Wireless connection" - depending on how you are going to connect your PC to the router, via wifi or cable. Click on desired type right click mouse and go to “Properties”.

Next, open “Internet Protocol Version 4” and set all parameters to “ Automatic receipt" If some data has already been registered here, then transfer it to paper - it will be useful for further setting up the router using the “Static IP” type.

Then we save the changes.

Setting up the ASUS RT-N12 VP router step by step

Now you can go directly to setting up the Asus RT-N12 router. We need:

1. Login to the admin panel
2. Change default password
3. Select the type of Internet connection
4. Specify parameters for the WiFi network

To go to the settings panel, open the browser and enter its IP address - where the entrance to the router is located. To authorize, enter the login and password admin/admin. How do I know them? They are used by default to enter the settings of the Asus router, and since we previously reset it with a “Reset,” I can say with 200% confidence that they will work.

Will open home page masters quick setup Asus. Click the “Go” button.

At the first stage, the software developer immediately takes care of access security - we change the Personal Area router.

After this, the firmware will independently try to determine your type of Internet connection:

• Dynamic,
• Static IP,
• PPPoE
• L2TP

You can find out it yourself from the contract with the provider. If the connection type is automatically determined correctly, click “Next”. If an error occurs and a different one is specified in the contract, then click on “Internet Type” and specify it manually.

Setting up Asus for Beeline

The Beeline provider uses the type L2TP. Therefore, if you are their subscriber, then we select this particular type on the Asus router.

• Username
• Password
• VPN server

They must be taken from the contract or obtained from technical support.

Internet connection Netbynet on Asus

Another popular provider, Netbaynet, provides services using the PPPoE, DHCP or Static IP protocols, depending on the client’s location.

Accordingly, you select the type indicated in your connection brochure. It is worth noting that with a dynamic IP (in Asus it is called “Automatic”), at Netbaynet you must check the “MAC Address Clone” checkbox

Since my Asus router is connected via the PPPoE protocol, then I need to enter authorization data.

How to set up a wifi connection on the Asus RT-N12 router?

After this, we proceed to setting up the Asus router for WiFi distribution— set a name for the wireless network and a password to connect to it.

Reverse side of the router last step check all configuration parameters and exit the quick wizard Asus settings.

That's all, actually. To make it easier to enter the settings of the Asus router, I added the address 192.168.1.1 to the bookmarks bar of the browser - now you can quickly go to the connection settings without entering it manually each time.

If you want to change something in your router after the first connection, then the Internet settings are located in the “Internet” section

And the parameters for connecting to WiFi can be changed by going to the “Wireless Network” menu

Video on setting up and connecting an Asus router

Don't know how to log into your Asus router? I'm afraid that if I say that the entrance to your personal account occurs at router.asus.com or 192.168.1.1 and authorization occurs through the login and password admin-admin, then many may not understand how exactly to do this. So let's talk about everything in order. First, let's figure out how to connect it to a computer via wifi, then log into the administrator system and configure WireLess. And at the end it awaits you visual video, which shows the entire process in detail.

This instruction relevant for Asus router models RT-N12, RT-N11P, RT-G32, RT-N10, RT-N10P, RT-N10U, RT-AC51U and others with a black admin panel of blue color.

So before we can go to ASUS router , you need to perform a series of actions and set a couple of configurations on the computer from which the setup will be done. Namely:

1. Connect the power adapter to the router and plug it into a power outlet
2. Enable Power Button
3. in “default” using the “Reset” button - it is small, located next to the antenna and recessed deep into the case. To press it, use a pin or pencil.
4. Remove the Internet cable from the computer and insert it into the blue WAN connector on the router body
5. Take the cable " twisted pair", from the router package and connect it to the PC in place of the Internet cable. Insert the other end into the yellow LAN port on the router - any of 4.

After that, go to the computer settings and find “Network and Sharing Center” in the Windows “Control Panel”:

(Start - Control Panel - Network and Internet - Network and Sharing Center shared access- Change adapter settings)

Here we find “Connect via local network", click on it right key mouse and go to the “Properties > Internet Protocol Version 4” section.

We check the boxes to receive all data “automatically” and save the settings with the “OK” button.

router.asus.com - how to log into your personal account Asus 192.168.1.1?

After this, you can already log into the router. Any device has a sticker, which Asus places on the bottom of the case. You can, of course, check me and look at its contents, but I can do this with eyes closed say what it says:

• Connection address - 192.168.1.1 or router.asus.com
• Login - admin
• Password - admin

Did you guess right? Otherwise! More than a dozen copies of such equipment had to be installed. If you are on previous step in your PC you did everything correctly, then when you enter “ http://router.asus.com" or " http://192.168.1.1"You should be taken to the web interface of your Asus personal account. Now you can go directly to, which is the subject of a separate detailed article - read!

I can't log into the router at Router.Asus.Com

Now let's talk about what to do if you do everything according to the instructions, huh. To begin with, I advise you to immediately look at how your Internet adapter is configured on your computer or laptop. It's either LAN card, where the cable is inserted, or wireless module. Depending on what you are connecting through.

Nowadays everyone mostly uses operating system Windows 10. Therefore, I will show you how to check these parameters in it.

The IP address of your ASUS personal account does not open

The error in logging into the Asus router via IP may also be due to the fact that it was once changed. That is, you just type incorrect value. Finally, there is another reason why the login page to the WavLink configuration interface may not be accessible. If this is the case, then in the “Status” section you can find the same IP address that is listed in the router settings in this moment.

Login and password admin are not suitable

Finally, if the authorization page still opens for you, but the standard login and password ADMIN indicated on the label is not suitable. What to do? This tells us that they were also replaced by previous setting networks. Unfortunately, only factory settings will help here.

Video on how to log into an Asus router