Setting up a tp link router personal account. The network interface is disabled. What if you have one of PPPoE, L2TP, and PPTP

IP address, aka html page 192.168.1.1 - this is the entrance to the router for most Asus models, Zyxel Keenetic, Netgear, Mercusys. You can also go to http://192.168.1.1 wifi settings branded routers or modems from providers such as Rostelecom or Beeline. Many models TP-Link personal The office is located at . To open the https 192.168.1.1 source and log into the router panel via the web interface, you need to know the login and password, which usually look like admin-admin.

Personal account address - 192.168.l.l, 192.168.l.0 or www 192.168.1.1 net ru?

But before you go into your personal settings wifi cabinet router, we will immediately eliminate the most common mistakes that users make.

The main thing when entering an address is not to automatically confuse and write 192.168.l.l(or 192.168.l.l0, 192.168.l.3) due to the similarity of the spelling of the letter L with the number 1 - a very common inaccuracy.
Another one common mistake, when commas are used instead of periods in the address - 192,168,1,1
The same applies to the computer's IP address if you enter it manually. You need to specify not 192.168.L.0, but 192.168.1.0
Finally, someone adds the ending NET, RU or COM. Another spelling option is with HTML, 192.168.1.1.html. You don't need to do this either.
Just as you should not write it with the prefix “www”.

Entering the settings of a new wi-fi router

But this is not enough. After all, even if you entered the correct IP address, you may not find the entrance to your router. Therefore, you need to ask yourself and answer the question:

Router, in Personal Area which you need to log in through the web interface, completely new or already used?

This is necessary to understand whether changes have been made to the standard IP 192.168.1.1 to enter your personal account settings. Otherwise, it may look like 192.168.1.4, 192.168.1.77, or any other. By the way, the same applies to the login-password pair, which usually looks like “admin-admin”. It could have been replaced with a more reliable one previous owner.

Web interface of the router’s personal account - http://192.168.1.1

To find out exactly what your router's default web interface address is, look at the sticker located on the bottom of its case. This source will necessarily indicate its IP in small print. In essence, he is html page, on which it is located Login to your router personal account. For manufacturers such as Asus, Netgear, Zyxel, Rostelecom, it will look like “ http://192.168.1.1". There are other options, for example - logging into your Huawei personal account, and - Xiaomi. However, they are rare and we talk about them directly in reviews specific devices.

In some models, instead of an IP address, a certain domain can also be specified for access to the web interface of the administrator section. It already replaces this IP address at the router software level. “Scientifically” it is called a hostname. So, for example, in Zyxel routers Keenetic can be reached either at 192.168.1.1 or “ “. U Asus— . And NetGear has routerlogin.net.

If you know the login and password for your personal account (admin-admin or another), you type the router IP correctly, but the login page to the web interface of the settings panel does not open, then check the network connection configuration on your computer.

Setting up a computer to log into the router at 192.168.1.1

In order to be guaranteed to access the router’s settings, you need to make changes to the computer’s network configurations in accordance with it. Otherwise, logging into your personal account will not be possible.

To get into these configurations, we follow the chain:

“Start - Control Panel - Network and Internet - Network and Sharing Center shared access» for Windows 7. Or right click to “Start” and then “Network Connections - Network Center” if you have Windows 10
Next, in the left menu, select “Change adapter settings.”
We find the active “Connection by local network", right-click on it and select "Properties"
Select “Internet Protocol Version 4”
Check the box automatic receipt ip and dns - in this case, the router will assign them to the computer independently.

After all this, save with the “OK” button.

Admin login 192.168.1.1 is not available

There is a problem that the web interface of the router’s personal account is also not accessible via the hostname mentioned above, but only via the IP address. This happens if in the settings network connection Third-party DNS servers are manually registered on the computer. You need to erase them, or specify the IP address of the router itself - 192-168-1-1.

Login to router 192.168.1.1 via cable

Next, connect the router to the computer. A few years ago this could only be done via wire. To do this, insert the Ethernet network cable (aka patch cord, twisted pair) one end into the network connector on the PC case, the other - into any LAN port router.

Don't get confused LAN ports and WAN - LAN is used to connect devices, including a computer, to the router. In the WAN we only insert the cable from the Internet provider. They are often painted in different colors.

Go to the administrator settings of the router via wifi

Today, everything is distributed to the router immediately after switching on wireless signal. You can connect to it and go to settings as with desktop computer, and a laptop. Sometimes it is not protected, as is done with TP-LINK. In some cases, the network is password protected. In any case, all data is indicated on the label.

How to log into the router 192.168.1.1 - login and password admin-admin

If the router is new, then there is nothing easier than finding out the login and password. We take the device, turn it upside down again and see that same sticker. On it, in addition to the IP address and network name that we have already looked for, in small print there are details for logging into the web interface, set by default - Login / Password. In most cases this admin/admin.

We are trying to use this data to log into the router’s personal account.

If the login-password pair “admin-admin” indicated on the case for authorization is not suitable, then look for the “Reset” reset button on the case. It is usually small and recessed inward to prevent accidental pressing. Perhaps someone in the store has already tested the router and set their own own password to log into the web interface at http://192.168.1.1.

Be careful - before resetting, make sure that you have written down all the data for connecting to your provider somewhere

Plug the router's power adapter cord into a power outlet. Take something like a pin (a pen or pencil may not fit into the hole). Press the sharp end on this button and hold for 10-15 seconds.

Sometimes it happens that the reset button is combined with WPS and is not recessed. Then just press it and hold it for the same 10-15 seconds until the lights blink.

Front Panel

LED indicators located on the front panel (from left to right).

Back panel

On the rear panel there are the following elements(from left to right).

ON/OFF : Power on/off.

POWER : Power connector. Use the power adapter included with the TL-WR841ND Wireless Router
1,2,3,4 (LAN) : These ports (1,2,3,4) are used to connect the router to computers on the local network.
WAN : The WAN port is used to connect an Ethernet network (provider).

WIFI ON/OFF: Used to enable/disable wireless broadcasting.

WPS/RESET : This button is used to enable WPS and to reset the router settings. To turn WPS on/off, simply press this button without holding it for more than five seconds; To RESET settings, press the button and hold it for more than five seconds. .
Wireless antennas : are used to receive and transmit data via a wireless connection.

Connecting a router

Choose a suitable location for the router. It is recommended to place the router in the center wireless network.
Adjust the antenna position. Most often the vertical position is best.
Connect your computer to your local network through the router's LAN ports (if you already have a wireless network adapter and if you want to use a wireless network connection, you can skip this step)
Connect the incoming Ethernet cable to WAN port router
Connect the power adapter to the appropriate connector on the router, and plug the other end into a power outlet. Turn on the router by pressing the ON/OFF button.

Setting up a computer to connect to the router:

In your computer's TCP/IP protocol settings, select Obtain an IP address automatically.

To access the router configuration, open a web browser and enter the default address http://192.168.0.1 into address bar browser.
A login window similar to the one shown in the image below will appear. In the User and Password field, enter admin, using lowercase. Then click the button OK or key Enter.

Setting up the router

After entering your Login and Password, the main Status window and the router configuration menu will open. The equipment can be configured in two ways: Fast And Individual setting.

Quick setup

To carry out quick setup, you need to select the item in the Main menu Quick setup

This will open a dialog box that allows you to select required parameters connections. In the first window you need to select Further.

Then a window will appear asking you to select your connection type. The router supports the five most common methods of connecting to the Internet - Dynamic IP address, Static IP address, PPPoE, L2TP and PPTP.

When choosing a connection type Dynamic IP You will be taken directly to the Wireless settings page.

When choosing a connection type Static IP address, the following window will be displayed

The settings that need to be entered in the appropriate fields are provided by the provider.

IP address– This is the WAN IP address visible to external users on the Internet (including your Internet Service Provider). Enter the IP address in this field.
Subnet mask– Subnet mask used by the WAN IP address.
Main gate– If necessary, enter the IP address.
Primary DNS server – If necessary, specify the IP address of the DNS server.
Secondary DNS Server– If you received a different DNS server address from your ISP, enter it in this field.

When choosing a connection type PPPoE, the following window will be displayed

Username: Password– Please indicate Username And Password, received from your Internet service provider. These fields are case sensitive.
Confirm password - Re-enter the password you received from your ISP to make sure the password you entered is correct. If the password differs from the value entered when confirming the password, a window will appear in which it will be written that the password does not match the previously entered one.
Dynamic IP address– Use dynamic IP address provided by your Internet Service Provider to connect to your local network.

After pressing the button FURTHER A window with wireless network settings will appear.

Wireless broadcasting– By selecting the appropriate item from the drop-down menu, you can enable/disable the function.
Wireless network name– Specify a value of up to 32 characters. The default SSID is TP-LINK_XXXXXX (XXXXXX is the last six unique characters of the router's MAC address). This field is case sensitive. For example, TEST And test- This different meanings.
Region– Select a value from the Russia drop-down list.

Mode- Mode wireless transmission router data. Allows you to select the broadcast standard b, g, n or mixed. Optimal setting is mixed mode, because it allows you to automatically connect to any device, regardless of the broadcasting standard (device).

Channel width– Select the appropriate value from the drop-down list. Default value Auto in which the device automatically adjusts the channel width for clients (it is better not to change).
Channel– This field specifies the operating frequency to be used. Default value Auto, so the access point will select the appropriate channel automatically. Change channel wireless connection not necessary.

Disable protection– The security function can be turned on or off. When the function is disabled, wireless stations can connect to the router without encryption (without a password - the network is not protected). We strongly recommend that you select one of the options to ensure security.
WPA-PSK/WPA2-PSK– WPA selection based on PSK password.
PSK Password – You can use format characters ASCII or Hexadecimal symbols
When choosing ASCII the key can contain numbers from 0 to 9 and letters from A to Z and its length must be from 8 to 63 characters. When choosing Hexadecimal, the key can consist of numbers from 0 to 9 and letters from A to F, and its length must range from 8 to 64 characters. Please note that the key is case sensitive. This means that the use of capitals and lowercase letters influences its meaning. You should write down the key and other wireless data security settings somewhere.

Without changes– When selecting this option, the wireless data transfer configuration will remain unchanged!

Pressing the button Further, You'll find yourself in the window Completion. Click the button Complete to complete Quick settings.

The router is configured and ready to go.

INDIVIDUAL ROUTER CONFIGURATION

After successfully logging into the router, you will see fifteen main menus on the left side of the web utility. The right side contains reference Information and instructions.

First menu item STATE. It displays general information about the device status. The information in this window is read-only and cannot be edited.

For customization router, you need to select the item in the menu NET, and select a section from the pop-up menu WAN.

By selecting Network - WAN you can configure network settings.

Setting up a DHCP connection

If you are using DHCP to obtain an IP address (automatically obtain settings), select Dynamic IP, and the router will automatically receive the IP parameters.

This window shows how WAN settings, including IP address, subnet mask, default gateway, and so on, are dynamically assigned by your ISP. To update the settings, you must click the button Update. To reset the values, use the button Release.

MTU size– Usually meaning MTU(maximum package size) for most Ethernet networks is 1500 bytes. We recommend that you do not change this value.
Primary DNS and Secondary DNS are assigned automatically. Use this function It is not necessary when assigning IP addresses dynamically.

Node name- This option allows you to assign a hostname to the router (not used on your network).
Get an IP address using Unicast DHCP– Some ISPs' DHCP servers do not support broadcast applications ( this option not used on your network).
Click the button Save to save settings.

Setting up a PPOE connection

If you are using a connection via the PPPoE protocol, then you should select the WAN option: PPPoE/Russia PPPoE.

When setting up a connection via PPPoE, you must specify the following parameters:

Username: Password– Enter the username and password you received from your provider from your provider. These fields are case sensitive.

Secondary connection– In this field you must select the connection type Dynamic IP.

Connection modeWAN- IN this section you need to select an item Connect automatically ( If the connection fails, it is automatically restored).

After selecting the parameters on this page, you must click the button Save.

Setting up a wireless connection

On the menu Wireless mode need to choose Settings wireless mode .

In this menu item you can basic setup parameters.

Network name– At this point you need to enter the name of your network to which you will connect. Enter a value of up to 32 characters. The default SSID is TP-LINK_XXXXXX (XXXXXX is the last six unique characters of the router's MAC address). This field is case sensitive. For example, TEST And test– these are DIFFERENT meanings.

Region– At this point you must select Russia.

Mode– Select mode 11bgn mixed. This mode allows all wireless stations of the 802.11b, 802.11g and 802.11n standards to connect to the router.

Channel width– Select channel width Automatically.

Channel- In this field you set the operating frequency that you are going to use. The default mode is Auto, thus, the access point itself is in automatic mode will select the most suitable channel . This parameter should be left in Auto mode.
Maximum transfer rate (Tx)- In this field you can limit maximum speed router data transmission (Tx).
Enable wireless broadcasting– The router's wireless mode can be enabled or disabled to provide access wireless stations. Wireless broadcasting can be turned on/off using the WIFI ON/OFF button on the router. By default, this item should be enabled.

Enable SSID Broadcast- When wireless clients search for the wireless network they want to connect to, they will see the SSID (network name) sent by the router. If you check the box Enable SSID Broadcast, That wireless router will openly broadcast its name (SSID). If the checkbox is not checked, then the network name will not be displayed in the list of networks and to connect you will need to manual mode enter network parameters for connection.

WDS- This field should be disabled (blank).
Click the button Save to apply your settings.

Setting up wireless network security.

By selecting from the menu Wireless mode- Wireless Security, you can configure the security settings of your wireless network.

Disable protection– If you do not want to use wireless security, click on the appropriate option. IN in this case your network will not be protected and anyone will be able to connect WiFi devices without password. (Not recommended)

Version– You must select the algorithm version WPA-PSK encryption from the drop-down list. The optimal mode is type WPA-PSK(WPA shared key).

Encryption- When choosing WPA-PSK or WPA You can specify one of the following values for the Authentication Type: TKIP or AES as an encryption algorithm. ( Not recommended enable encryption type TKIP, because this encryption is not supported by the 802.11n broadcast standard). In this setting item you need to select a standard AES.

Wireless password– Here you can specify a password of 8 to 63 characters in length. ASCII encoding(that is, it is acceptable to use capital and lowercase letters and numbers of the Latin alphabet).
Group key update period– This field must contain the value 0.

This completes the setup of your router and it is ready to use.

The tplinkwifi.net address is used to enter the settings of TP-Link routers. Web interface, router website, personal account, settings page, system - as they name it, the router control panel, which can be accessed through a browser by going to the address indicated on the router. If you are unable to access the settings of your router, now I will try to explain in detail what and how to do to access the router settings.

Not long ago, TP-Link began using the address to enter the settings of its routers tplinkwifi.net. Including for models: TL-WR841N, TL-WR741ND, TL-WR940N, TL-WR840N, TL-WR720N, etc. You most likely saw it on the case of the router itself, or in the instructions. Also pay attention to the factory login and password (admin and admin). They are also required to enter the settings page. This information will look something like this:

Previously, the IP address was 192.168.1.1, or 192.168.0.1. But even now, at 192.168.0.1 you can enter the settings. So, if your tplinkwifi.net address does not work, you can try going to 192.168.0.1.

Now let's try to figure out why you didn't go to the page with your settings at tplinkwifi.net Wi-Fi router, and to this site.

How to log into tplinkwifi.net and enter the username and password admin?

You just need to type the address in the browser and go to it. Next, the authorization page should open, where you need to specify your login and password (admin, if you have not changed them), and log into the web interface. But, if you are reading this article, then most likely you were not able to do this. Let's try to find out why.

1 The most important point is the device from which you are trying to log in TP-Link router, must be connected to the router via network cable, or via Wi-Fi. I think this is clear. I showed this in more detail in the article: . If you are not connected to the router, then most likely a page like this will appear with a message:

Another important point here is that there may be no access to the Internet. (yellow Exclamation point near the connection icon), since your router is most likely not yet configured to connect to the Internet. But this is not scary, since you don’t need the Internet to access tplinkwifi.net.

2 It seems to me that the most main mistake The problem is that many people enter the address not in the address bar of the browser, but in the search bar. And therefore it is not the router page that opens, but the search results in search engine, where you most likely came to my article. If it doesn’t work, for example, in the Opera browser, then you can try logging in through Chrome, or Microsoft Edge in Windows 10.

You need to do two things:

Go to tplinkwifi.net (or 192.168.0.1).
Enter your username and password. Factory settings: admin and admin.

After this, the control panel should open. The page itself may differ depending on the firmware.

3 If the login page does not open, then it may well be that the problem is network settings your computer. You need to check that the IPv4 protocol properties of your connection to the Internet (router) are set to automatically obtain IP addresses.

Some more tips and links to useful articles:

Check your connection to your TP-Link router. Is it turned on? It is possible that your computer or laptop is connected to the Internet in another way, for example, via Wi-Fi. Disable all connections, leaving only the router whose settings you want to go into.
Try visiting tplinkwifi.net from a different browser. Or better yet, from another phone, computer, tablet. Try it.
It is possible that the router address or login and password have been changed. In this case, either the settings page will not open at all, or the error that the password and/or login is incorrect will not appear. In this case, you need to do.
If you still cannot access tplinkwifi.net, then see the recommendations from the article:.
There is no need to rule out a hardware failure of the router. Pay attention to the operation of the indicators.

If you did not find the answer to your question in the article, or something is not clear, you can leave your question in the comments. There you can share some useful advice on this topic.

Connect the cable brought into the apartment to the WAN port of the router.

Connect your computer to one of the LAN ports on the router Ethernet cable included in the delivery.

Configure your computer's local network connection to automatically obtain an IP address and DNS server addresses. For this:

In the operating room Windows system XP: "Start" / "Control Panel"/"Network connections" "Internet Protocol (TCP/IP)"

IN operating system Windows 7: Start / "Control Panel"/"Network and Internet"/"Network and Sharing Center"/"Change adapter settings". Right-click on the local network connection icon and select "Properties". Select a line "Internet Protocol Version 4 (TCP/IPv4)" and click the "Properties" button. In the dialog box that opens, select the options “Obtain an IP address automatically” and “Obtain a DNS server address automatically.”

Click the OK button, then the Close button.

Launch your browser, enter http://192.168.0.1 in the address bar and press the Enter key on your keyboard.

A dialog box will appear asking you to enter your username and password. The factory default username and password are admin/admin. After entering your username and password, click OK. A web interface for managing the router will be displayed in the browser window.

In the menu on the left, select “Network”, then “WAN”. In the dropdown list "Type WAN connections» select item "Static IP address". In the input fields “IP address”, “Network mask”, “Default gateway”, “Primary DNS” and “Secondary DNS”, enter the settings given to you at the INFO CENTER office. Then click the "Save" button.

Your router is ready to work with the Internet via a wired connection.

If you would like to set up wireless access(Wi-Fi), select from the menu on the left "Wireless mode", then "Wireless Settings". Think up and enter the name of your wireless network (in Latin letters), enable (or make sure they are enabled) options “Enable wireless broadcasting of the router” and “Enable SSID Broadcast.” Then click the "Save" button.

After that, select the item on the left menu "Wireless Security"". Select the security type (select the switch) “WPA-Personal/WPA2-Personal”. Create a password consisting of 8 or more characters (numbers or Latin letters) and enter its “PSK Password” field. Click on the "Save" button.

In order for the wireless mode settings to take effect, you need to restart the router. To do this, select an item in the menu on the left and click the button.

Internet access is controlled through your personal account.

For detailed instructions on setting up your router, you can