The computer does not remember the date and time. Solving the problem of incorrect clocks. The date and time on the computer constantly gets lost. Why does this happen and how to fix it

The main reasons why the time is lost are battery failure, updating when choosing the wrong time zone and third party programs, changing the date. Each of these reasons for the system clock not working properly can be easily fixed at home.

Dead CMOS battery

The computer clock does not stop timing even when the device is disconnected from electrical network. CMOS power is provided by a coin cell battery. motherboard, usually having a voltage of 3V. It is designed for continuous operation for several years, but when you turn on the computer, the element does not charge. Therefore, if the power supply runs out, for normal operation clock needs to be replaced.

Important! Buy new battery You can do this not only in a computer store, but also in the corresponding departments of other stores.

To replace the CMOS battery: the following actions:

1. Turn off your computer.
2. Turn off the power.
3. Remove the side cover system unit.
4. Locate the battery (usually located in the lower right corner of the motherboard).
5. Use a screwdriver or other object to bend the metal holder.
6. Paste new element power supply, observing the polarity (plus is located on top).
7. Close the system cover and turn on the computer.
8. Restore if necessary standard settings BIOS.
9. Install correct parameters time.

Note! In order for the new battery to fit, it must have the same markings as the old one. This is often CR2032, but CR2016 and CR2025 can also be used.

Time is translated by viruses or program activators

Use of unlicensed software with activators can lead to the time on the computer being lost. Some programs have free versions, limited in operating time. To renew a license, activators use a simple method of setting the clock back. If the time starts to go wrong after installing such software, uninstall it.

The clock can also change malware. If you do not have an antivirus installed on your computer, download any free tool checks that do not require installation. For example, "Zillya", "Dr.Web CureIt" or " ESET Online Scanner". IN latest versions Windows also has a built-in antivirus. Open " Windows Defender" by clicking on the tray icon. In the right column, select the scan type and click “Check Now.” Available options checks:

• Fast
• Full
• Special

When scanning your computer for the first time, it is recommended to select full check. Selected on previous step The mode determines the duration of the process. The scan time is also affected by the speed of the device and the amount of hard disk space. You can stop scanning for viruses by clicking the “Cancel scan” button.

Important! Before starting the scan, do not forget to download the latest antivirus databases on the "Update" tab.

Useful video: Solving the problem of spontaneous time reset on a computer

Wrong time zone

If the time zone on the computer is set incorrectly, the time will be lost when synchronizing the clock. Even if after this it is installed right time, next update over the Internet will return values ​​for a different time zone. To change these settings, click on current time in the lower right corner of the screen. Follow the link on the calendar pop-up window.

Greetings, friends! My friends contacted me several times different problems in the operation of the computer, the reason was the discharge of the three-volt battery inside the system unit.

And the problems were the following: someone’s anti-virus programs stopped working correctly, they began to panic because of license errors when trying to update. They refused to work with the Internet and showed errors connecting to the server. Every time I turned on the PC it happened again. And only one paid attention and asked why the time on the computer was lost after it was turned off.

Source of the problem

A CR2032 battery, the size of a ruble coin, is located on the computer and powers the CMOS memory, which stores BIOS settings, including date and time. Why is the date not lost when rebooting the computer? The fact is that at this moment the supply voltage is provided by work. And after disconnecting from the electrical network, the voltage disappears, and the data in the volatile CMOS memory is lost. Conclusion - the battery needs to be replaced.

If you have desktop computer, then you can change it yourself. Disable power cord. Remove the side wall and carefully pull out the battery, pressing the lock. Put a new one in its place. And, if you are the owner of a laptop, then it is better to contact a specialist, because disassembling a laptop is much more difficult. You can also ask to clean your laptop to avoid overheating in the future.

After replacing the battery, you need to set correct date and time. This can be done in the BIOS settings or in the operating system itself. Click right click mouse on the computer clock and select Set date and time.

On the Date and Time tab, you can change the time zone, current date and time.

Sometimes there is a problem with the transition to summer time, then this can be solved by updating the system. In Windows 7 and higher this problem no longer exists, but in Windows XP it may still exist.

On the Internet Time tab, you can configure your computer to automatic synchronization with a time server. Then, when you turn on your computer, it will synchronize the time with the Internet. I specify timeserver.ru as the time server. Unlike other time servers, it doesn't let me down.

I hope you learned a little useful information for myself. Have you ever had similar problem and how did you solve it? Share your experience in the comments.

Dear reader! You have watched the article to the end.
Have you received an answer to your question? Write a few words in the comments.
If you haven't found the answer, indicate what you were looking for.

Many people lose time on their computer and it happens quite often, but if you find out the reason, the problem can be solved quite easily.

Why does the date and time get lost?

One of the most common reasons, due to which the date and time on the computer fails - the battery life of the motherboard has expired. In this case, the date and time on the computer are lost in almost all cases. Moreover, the reset will occur every time the power to the system unit is turned off.

To check you need to go to Motherboard BIOS boards and see set time. If it goes wrong, it means the battery is dead. To replace it after turning off the power, you need to remove the system unit case, find the motherboard and remove the battery from under the latch. A dead battery must be replaced with a new one with the same marking. After replacing the battery, turn on your PC and launch the BIOS again. Install right time and date. After this, the same must be done in the operating system.

If you set the time zone on your computer incorrectly, the time will also be constantly lost. What to do? To correct the time, you need to click on the time panel, enter the “change date and time settings” option and change the time zone. After this, you need to check synchronization with the server; if the time matches, you did everything correctly.

In connection with the abolition of daylight saving time in Russia, another problem has arisen. Time on a PC is either one hour ahead or behind. This problem relevant for Windows 7, which can be resolved by downloading updates for the specified operating system. If you notice that the clock on your computer is going an hour ahead or an hour back, hurry up.

When using activators and utilities that reset test period V paid programs, the time and date are changed to extend the program. The problem is solved after Windows reinstallation on your computer.

Sometimes viruses can cause time outages. Why don't you install it on your PC antivirus program and not?

As you can see, fixing the time problem on your computer is not that difficult. We hope our instructions clearly explained what to do if the time on your laptop or computer is lost.

Important update from October 26, 2014! Time zones in Russia have been changed and for those who have set automatic time synchronization, the clock will always go wrong... set everything Latest updates on Windows or disable time synchronization.

Hi all. Today I want to tell you about one not entirely pleasant problem that inevitably awaits all computer users who have not changed the battery in their computer for a long time (some do not even suspect that there is one in their big brother, and this is one of the main reasons why time on a computer gets lost).

However, not only a dead battery can be the reason why system time differs from the present, ours, in which we live and work.

5 signs why the time on your computer is lost

1. From time to time you notice that the time on your computer is set incorrectly. If the difference is several hours, then most likely the time zone is not yours and automatic time synchronization is enabled, so no matter how much you set the correct values, synchronization will still occur and the time will be set for the time zone set in the system.

Important note! It is quite possible that you have bad programs that can block the time settings... in this case, we need to remove unnecessary programs...

This throws you back several years (usually to the date the motherboard was manufactured). In this case, we can say with confidence: you need to change the battery on the motherboard

2. When we start the computer, we can see the inscription. Next you need to press F1 or F2 to configure BIOS parameters(This error does not always indicate a faulty battery, but in 99% of cases it is)

3. It is impossible to access most sites, for example, when trying to access Yandex mail, instead of the usual inbox, we will be shown a message that this connection is untrusted (most likely, the certificate simply has not started to work, you are now in the past)

4. If you are using antivirus and others similar programs, then most likely you will receive a message that the license has expired or has not expired... or that the databases are out of date. I wouldn’t be surprised if the program activation completely fails.

5. Many programs will frankly be “buggy”, or even refuse to start at all. This is the first thing that came to mind. In fact, there can be a lot of problems, sometimes such a small problem can cause great harm. If you work in 1C and check out something from the warehouse, then all this will be carried out according to the date set in the system, which can then become a major problem.

What to do if the time on the computer is lost?

1. Check the time zone and synchronization
2. Change the battery on the motherboard

1. The time is wrong due to the wrong time zone

I think I won’t open America to anyone if I say that not so long ago Medvedev came up with a bunch of changes with time zones in Russia. Due to the fact that automatic Windows update disabled for most users - this may cause some roughness in working hours! For example, before I belonged to the time zone (+5 hours Yekaterinburg), although I am now in the same time zone, but now it is already (+6 hours Yekaterinburg).

If not installed necessary update on Windows and leave everything as it is, then you don’t have to wonder why now my time is constantly behind by an hour, even if we correct the time ourselves (after all, during the next synchronization, the system will set the correct time for the desired time zone)

What can be done in this case? — The answer is simple: disable time synchronization or set a suitable time zone. To do this, you need to click on the informer with a clock in the lower right corner and click “Change date and time settings...”

Here we need to set the time zone we need. To do this, you can install an update on Windows or choose the one that suits us! +6 hours for Yekaterinburg completely coincides with the Astana time zone, so you can leave it and not touch anything else.

You can go to the “Internet Time” tab and set up automatic synchronization. This is necessary so that if you set the right time and it will not be adjusted. I would not recommend this option, but maybe someone will need it.

This is where the parameters are set. Right here you can perform time synchronization immediately.

I hope with software problems We figured it out - let's move on to the “iron” ones.

2. Change the battery on the motherboard

The most common reason why the time on a computer goes wrong is a dead battery. The fact is that when the computer is disconnected from the electrical network, it needs power so that the system time does not get lost and the BIOS settings are stored. In those moments when there is no power, battery energy is consumed. (Many people are surprised that the laptop also has such a battery)

Such a battery can be bought at any store where you can buy batteries (sorry for the tautology)... It is called CR2032 and has a voltage of 3 volts. It is quite inexpensive, and you can notice it yourself without much hassle.

Open the cover of the system unit and inspect the motherboard. It often happens that the battery is not visible due to the video card or some other bulky piece of hardware. As a rule, there is a holder on the side; if you press on it a little, the battery will “pop out” on its own. special effort. If you have to use force to get it, then you are doing something wrong.

Today we will deal with the problem: why the date and time settings may get lost when loading the operating system. Don’t worry, nothing bad happened to your computer and the issue can be resolved on your own.

Time Zones

The first reason could be an incorrectly selected time zone. Therefore, when you load the operating system, the time is synchronized with the server and, accordingly, is set incorrectly.

To view which time zone is selected for you, you need to right-click on the clock located in the tray and select the item from the context menu "Setting the date and time".

In the next window, look at the set time zone. If it is selected incorrectly, click on the button "Change time zone..." and set the desired value. Then click on the “Apply” and “OK” button.

Change to another time

The second reason is the automatic transition to summer/winter time. As is known, this transition has been canceled in Russia since 2014. That is why the clock on your computer can either lag or rush by 1 hour.

To solve this problem, you simply need to update the installed operating system. If, for known reasons, you cannot do this, then we will consider other methods.

To do this, right-click on the clock in the tray again and select from the context menu "Setting the date and time". In the next window go to the tab "Time on the Internet". Here we click on the button "Change settings". Now you need to uncheck the box “Synchronize with Internet time server” and click "OK". Then click “Apply” and “OK”. Then simply set the correct time.

You can also try changing the time zone. For example, you had UTC+03.00 set, change it to UTC+02.00.

The battery on the motherboard is dead

The third reason why the time and date on the computer are lost, it could be a dead battery on the motherboard. Moreover, they get lost every time you turn off the power to the system unit.

The thing is that when the computer is disconnected from the mains power, the system time and BIOS settings are not lost only due to the power received from the battery. Therefore, when it sits down, when loading the operating system, a window may appear where you, and then the time and date are incorrect.

In this case, you need to disconnect the system unit from the network and deploy it back cover towards you, unscrew the screws that secure the side covers. Then remove the side cover and locate the small battery on the motherboard. It is shaped like a tablet, provides a voltage of 3 volts and is usually called CR2016, CR2025, CR2032. Carefully take it out, it is secured there with a latch, and buy the same one in the store - they are not expensive. Then install the battery and put the parts of the system unit back together.

Now turn on the computer and immediately. This can be done by pressing F2 or Del when loading the operating system. We set the correct date and time there. Then we exit the BIOS and wait for the system to finish loading. Then simply set the correct date and time on your computer.

Viruses

The fourth reason can be called computer viruses. At the same time, they are introduced into system files and because of this, the date and time settings may be lost.

Check your computer with an antivirus program. Moreover, it is better to do this not only with the one installed on the computer, but also with a couple of others. If something is wrong, remove any viruses found. If you are still in doubt, check non-system drives for viruses, format system disk and on the computer. You can read more about this in a separate article.

I hope that one of the methods discussed above will help you. And when loading the operating system you will no longer be disturbed incorrect settings date and time on your computer.