How to insert a second DVD drive into a computer. CD-ROM Installation

Instructions

Remove the side covers of the system unit and remove the old drive. Disconnect the wires leading to it from the power supply and motherboard, carefully unscrew the bolts and slide the drive forward out of the case. It comes out quite easily. Carefully unscrew all bolts and try not to lose them.

In the same way, install the new drive in place of the old one. Before installation, check which connection connectors your new DVD drive has. If your old drive had IDE connections and you purchased a SATA device, check to see if there are SATA connectors on the motherboard and power supply. Carefully inspect the internal contents of the system unit on your computer. Usually, new components come with a small installation manual. Insert one end of the cable into the connector of the newly installed drive, and the other into the corresponding socket on the motherboard. Connect the wires from the power supply to the drive.

Reinstall the side covers of the system unit and tighten the bolts. Connect all wires to the system unit and start the computer. Check if it is determined motherboard new device. To do this, go into the BIOS by pressing the Del key on the keyboard when the computer starts booting. Usually you have to press Del several times in a row until it opens BIOS menu.

After downloading operating system Launch the Device Manager application. Check whether a new drive is installed in the system - there should be no items with question marks or exclamation marks in the list of devices. Check the operation of the new drive by reading the information from the disk. Replacing a DVD drive takes no more than 10-15 minutes.

Video on the topic

Often there is a need to install a second floppy drive or optical disks. To ensure that there is no conflict between two drives connected to the same cable, certain rules must be followed when modifying the machine.

Instructions

Shut down the operating system. Turn off the power to your computer.

Before installing a second optical drive, make sure that cables are connected to both IDE connectors on the motherboard. If that's not the case, second connect the cable in such a way that the conductor on which the stripe is applied (usually red) is connected to the connector pin marked 1.

To prepare the system unit case for installing the drive, remove the plastic plug for one of the 5.25-inch bays from the front panel. If there is a second, metal plug behind it, break it off.

Insert the drive into the bay, then secure it with four screws on each side.

Correctly redistribute the drives between the loops. One of them should have only optical drives, the second - only hard disks.Connect the cable connectors to all drives so that the conductor with the strip faces the power connector of the drive.

If before there were three hard drives and one optical drive, then after installing the second optical drive one of hard drives will have to be disconnected. In the future, it can be connected via a RAID controller or a USB-IDE adapter.

Now you need to set the jumpers on the drives correctly. The jumper positions for the "master", "slave" and "cable select" modes are indicated on the drive cases. On a hard drive, to change the mode, you usually have to rearrange several jumpers, on an optical drive - only one. On each of the cables, either one of the drives should be switched to the "master" mode, and second- “slave”, or switch both drives to “cable select” mode.

Be sure to connect the power connector to the newly added drive.

Connecting drives with SATA interface has two. Firstly, there is no need to select the "master" and "slave" modes. Secondly, cables of this standard come in two types: with and fifteen contacts. You only need to connect the power connector to the drive in the first case. If you supply power through a separate connector to a drive connected in the second way, it may fail.

Although predictions about the appearance large quantity The software on the DVD-ROM has not yet been confirmed, installation DVD-ROM drive when updating equipment, it has still become one of the most popular and is especially useful when you plan to watch movies on the PC. In addition, such drives can read both standard CD-ROMs and CD-RWs, and some newer models (which are essentially combined devices) are also additionally capable of writing CD-RWs.

When recording DVD movies, MPEG-2 compression technology is used, so be sure to various options decompression. To improve your viewing experience, hardware decompression is recommended. Some drives come with software for playing DVD movies, but to play them without delays or dropped frames, you need a computer with a fast processor and plenty of RAM.

In many modern graphics cards There is built-in hardware support for MPEG-2 decompression, so before purchasing a DVD-ROM drive, check the description or website to see if your video card can support it. If everything is in order, then when buying a DVD-ROM drive you can save money by not using additional fee-decoder. Otherwise best choice There will be an all-in-one upgrade DVD-ROM kit. Such sets (for example, the Creative Labs DVD Encore described below) include a card with hardware MPEG-2 decompression, allowing you to get the same high quality DVD movie, just like on a separate DVD player. In addition, most of these boards also contain an S-VHS connector, which is considered a big plus for watching movies on TV.

So, you should seriously think about purchasing a DVD-ROM drive only when the PC is equipped with a processor of at least Pentium II-400 and at least 32 MB of RAM (only a slight deviation is acceptable). And to get maximum pleasure from watching DVD movies, you will need a high-quality sound card and speakers (for information on installing a sound card, see the next issue).

1. Check the functionality of your PC. Installing a DVD-ROM drive, an additional MPEG decoder card, and the associated software will significantly change the configuration of your PC. Therefore, before you start upgrading, make sure that your computer works without failures. Click the "Start" button and select "Settings? Control Panel", double-click the "System" icon and check the "Devices" tab ( Device Manager). If there is a Exclamation point, then click the “Start” button again, check the “Help” item, find the “hardware troubleshooter” section and follow the instructions there. Do not forget that before starting any modernization it is necessary to carry out a complete backup data.

2. Install the decoder board. Turn off the PC, disconnect it from the power supply and remove the cover from the system unit. Be sure to use an antistatic wrist strap connected to a grounded metal object. Find a free PCI slot and remove the corresponding metal plug from the back of the PC case. Carefully insert the board into the slot and secure with the screw.

3. Install the DVD-ROM drive. Motherboards have primary and secondary IDE connectors. Best place connecting a DVD-ROM drive - an IDE channel that serves the CD-ROM drive. Locate an open connector on the wide data cable connected to this channel. If you don't have one, take the cable from the DVD-ROM kit.

When the secondary channel already has two devices (for example, CD-ROM and CD-RW drives), then connect the DVD-ROM drive to a free IDE connector on the hard drive channel.

Make sure the jumper on the back of the DVD-ROM drive is in the Slave (A) position. If you need special brackets to install the device in your PC, secure them. Insert the drive into an open bay on the computer (B) and connect the wide data cable and power cable to the appropriate connectors on the back of the DVD-ROM drive (C). Make sure the colored wire of the data cable (usually red) is connected to the first pin of the DVD-ROM drive connector.

4. Connect the cables. A typical DVD-ROM upgrade kit includes many cables and necessary connectors - completeness options depend on the manufacturer. The instructions given here apply to the Creative Labs PC-DVD Encore 12X set with Dxr3 decoder. Please read the included manual carefully and work slowly and methodically.

Connect the audio cable from the upgrade kit to the back of the DVD-ROM drive and to the audio-in jack on the MPEG card.
If the audio cable is from an existing one CD-ROM drive brought to sound card, then switch it from the latter to the audio-in of the MPEG board.
Connect with an audio cable line output(line-out) MPEG cards and internal CD audio input of the sound card.
Disconnect the monitor cable from the video card connector in the PC and connect it to the bottom connector (the external monitor-external monitor) MPEG boards.
Connect the MPEG card to the PC video card using the special cable included in the DVD-ROM drive kit (loopback cable).
If you plan to watch DVD movies on TV, then connect it with a cable to the MPEG card. If your TV has an S-Video input (to improve quality), you will need special cable(most DVD-ROM drive kits do not include this). Otherwise, use the split video to full video adapter included in the kit. To complete the TV connection, you will need a standard RCA cable, also not included with the DVD.
If you have an AV receiver or PC speaker system that can handle Dolby Digital Surround Sound, connect it with a cable (usually not included with the DVD-ROM) to the MPEG card.

5. Install drivers and software for DVD-ROM drive. Connect your PC to power and turn it on. Windows system should detect new devices and request their drivers. Insert the supplied floppy disk (or CD-ROM) into the appropriate drive of your PC and follow the on-screen instructions.

After installing the drivers, install the DVD-ROM drive software. Be sure to follow all instructions in the instructions - details depend on the specific kit.

Now make sure that new drive reads both CD-ROM and DVD-ROM. There is a problem? Turn off your PC and double-check all connections: It can be easy to get confused with the many cables in an upgrade kit. If problems persist, call customer service. technical support kit manufacturer. If everything works correctly, turn off the PC, put it on system unit cover and start the computer again. Pop in your favorite DVD movie, grab some popcorn, sit back and enjoy the show.

A disk drive, or optical disk drive, is a device used for reading and. Although optical discs They are losing their popularity every year; it is still impossible to do without a disk drive, especially on a desktop computer. In this article we will talk about how to connect a disk drive to a computer.

Step No. 1. Prepare the computer to connect the drive.

Before you begin directly connecting the drive to your computer, you need to perform a number of preparatory operations. First, the computer must be completely de-energized. Not just turn it off, but completely cut off the power. To do this, you need to pull out the cable that connects the computer to the power supply. This simple action will protect you from electric shock and save your life.

After you have turned off the power to the computer, you need to remove the side covers of the system unit. We need to remove both covers, since to connect the drive to the computer we will need access to both sides of the system unit.

As a rule, the side covers are secured with four screws at the back of the system unit. After unscrewing these screws, move the side covers back a little and then remove them.

Step #2: Distinguish old floppy drive from your computer.

If your computer has an old disk drive that you want to replace, you will first need to unplug and remove the old disk drive. To do this, unscrew the screws that secure the drive. As a rule, there are four of these screws, two on each side of the drive.

After you have unscrewed the screws, the drive must be carefully pulled out of the system unit. To do this, push the drive slightly out of inside system unit and pull it out.

It should be noted that it can only be removed from the outside of the system unit. Therefore, you should not try to push the drive inside the computer case.

Step No. 3. Connecting the drive to the computer.

Now we come to the real important issue This article shows how to connect a disk drive to a computer. To do this, insert the drive into the free compartment on the front side of the case and push it in until it stops. After the drive is in place, it needs to be secured with screws. Don't skimp on the screws; tighten all four of them, two on each side of the drive. If the drive is poorly secured, it will vibrate and make a lot of noise when writing or reading discs.

After the drive is installed, you need to connect it to the computer. All modern disk drives are connected just like hard drives, using cables. All you need to do is plug a narrow SATA cable (usually red) into a free SATA port on the motherboard and into the drive. You also need to connect a cable with SATA power, which comes from the power supply. Cable SATA power supply slightly wider and consists of 4 conductors.

Once you have connected the SATA cables to your drive, you can close the side covers and turn on the computer. This completes the process of connecting the drive to the computer.

We installed it in the case of the assembled computer HDD, it's time install optical drive. From a technical point of view, it is now completely unimportant what type of disks your drive is designed for. Be it CD, DVD or BlueRay drive unit, the installation will look exactly the same. Perhaps the only exception may be some exotic drives, which may be smaller in height than the standard version.

What is a DVD drive for?

I hope the purpose of this device is clear in its essence. Everyone knows that a DVD drive is needed to read and write optical discs. Once upon a time, in the nineties of the last century, when no one had heard of the DVD and, especially, BlueRay formats, not every computer had a drive for reading optical discs.

Moreover, at one time I myself, as a teacher of IT-related subjects, personally gave failures to students who said that they could write their information on a CD. At that time it was simply unthinkable - all optical discs were recorded only using an industrial method.

Then they began to appear devices for recording information on CD. However, at first they were so expensive that for the cost of the recorder you could buy a Zhiguli car, and the cost of the blank was approximately equal to the monthly salary of the employee who dealt with it. It’s easy to imagine the trepidation with which people held this miracle of technology and engineering in their hands.

By the way, initially devices for reading, and even more so writing, optical discs generally belonged to the category external devices both in size and appearance resembled a small inkjet printer.

Now these devices are beginning to be gradually replaced by more convenient and compact flash drives, which can hold much larger volumes and take up much less space.

Many modern laptops are no longer equipped with a DVD drive in order to reduce the size of the laptop itself.

When a person collects desktop computer, he can easily fall under the influence of these newfangled trends and abandon the DVD drive in his future desktop. However, in our humble opinion, this should not be done. The fact is that while many programs, external device drivers, etc. supplied on CD. Sometimes you may have to write some information to disk. In a word, it is better to buy and install it in new computer optic DVD-RW drive(or BlueRay for exotic lovers).

Lesson 5. how to install a DVD drive into a computer

The next lesson will be dedicated to

Although predictions about the appearance of a large number of software on DVD-ROM have not yet been confirmed, installing a DVD-ROM drive when upgrading equipment has still become one of the most popular and is especially useful when you plan to watch movies on your PC. In addition, such drives can read both standard CD-ROMs and CD-RWs, and some newer models (which are essentially combined devices) are also additionally capable of writing CD-RWs.

When recording DVD movies, MPEG-2 compression technology is used, so various decompression options should be provided. To improve your viewing experience, hardware decompression is recommended. Some drives come with software for playing DVD movies, but to play them without delays or dropped frames, you need a computer with a fast processor and plenty of RAM.

Many modern graphics cards have built-in hardware support for MPEG-2 decompression, so before purchasing a DVD-ROM drive, check the product description or website to see if your graphics card can support it. If everything is in order, then when purchasing a DVD-ROM drive you can save money by not having to use an additional decoder board. Otherwise, your best choice is an all-in-one DVD-ROM upgrade kit. These sets (such as the Creative Labs DVD Encore described below) include a card with hardware MPEG-2 decompression, allowing you to get the same high-quality DVD movie as a separate DVD player. In addition, most of these boards also contain an S-VHS connector, which is considered a big plus for watching movies on TV.

1. Check the functionality of your PC. Installing a DVD-ROM drive, an additional MPEG decoder card, and the associated software will significantly change the configuration of your PC. Therefore, before you start upgrading, make sure that your computer works without failures. Click the "Start" button and select "Settings? Control Panel", double-click the "System" icon and check the "Device Manager" tab. If there is an exclamation mark next to any device, then click the “Start” button again, check the “Help” item, find the “hardware troubleshooter” section and follow the instructions there. Don't forget that before starting any upgrade, you need to perform a full backup of your data.

3. Install the DVD-ROM drive. Motherboards have a primary and secondary IDE connector. The best place to connect a DVD-ROM drive is the IDE channel that serves the CD-ROM drive. Locate an open connector on the wide data cable connected to this channel. If you don't have one, take the cable from the DVD-ROM kit.

When the secondary channel already has two devices (for example, CD-ROM and CD-RW drives), then connect the DVD-ROM drive to a free IDE connector on the hard drive channel.

Connect the audio cable from the upgrade kit to the back of the DVD-ROM drive and to the audio-in jack on the MPEG card.
If the audio cable from an existing CD-ROM drive is connected to the sound card, then switch it from the latter to the audio-in of the MPEG card.
Connect the audio cable between the line-out of the MPEG card and the internal CD audio input of the sound card.
Disconnect the monitor cable from the video card connector in the PC and connect it to the bottom connector (external monitor connector) of the MPEG card.
Connect the MPEG card to the PC video card using the special cable included in the DVD-ROM drive kit (loopback cable).
If you plan to watch DVD movies on TV, then connect it with a cable to the MPEG card. If your TV has an S-Video input (to improve quality), you will need a special cable (most DVD-ROM drive kits do not include one). Otherwise, use the split video to full video adapter included in the kit. To complete the TV connection, you will need a standard RCA cable, also not included with the DVD.
If you have an AV receiver or PC speaker system that can handle Dolby Digital Surround Sound, connect it with a cable (usually not included with the DVD-ROM) to the MPEG card.

5. Install drivers and software for your DVD-ROM drive. Connect your PC to power and turn it on. Windows should detect new devices and request their drivers. Insert the supplied floppy disk (or CD-ROM) into the appropriate drive of your PC and follow the on-screen instructions.

After installing the drivers, install the DVD-ROM drive software. Be sure to follow all instructions in the instructions - details depend on the specific kit.

Now make sure that the new drive reads both CD-ROM and DVD-ROM. There is a problem? Turn off your PC and double-check all connections: It can be easy to get confused with the many cables in an upgrade kit. If problems persist, call the kit manufacturer's technical support line. If everything works correctly, turn off the PC, put the cover on the system unit and start the computer again. Pop in your favorite DVD movie, grab some popcorn, sit back and enjoy the show.