Beeline wifi connection. Incorrect login or password. Preliminary steps before setting up

Many providers provide network access, but Beeline is considered one of the popular options. The company provides mobile 4G Internet or home connection. You can set up a connection through a proprietary modem or a router from another company to get Wi-Fi coverage. Configuration may vary depending on device model.

Setting up a router for Beeline

When using several computers at home, the task of setting up Wi-Fi becomes urgent. Wireless Internet especially convenient if you have modern smartphones, tablets or laptops. Setting up Beeline through a router can be done automatically or manually, it depends on the device model. As a rule, when a contract is concluded, a master comes home to help create a connection. If the Wi-Fi installation was carried out later, or the device was replaced, then the connection will have to be configured again.

For each device there are instructions for setting parameters for proper operation, but there are points that are the same for each case. Eg:

connect the wire (cable) to the router;
connect the device via the second wire to the computer;
Configure the device (enter the Beeline router address, set the connection type, set a password and connection security).

Setting up a Beeline DIR-300 router

There are several popular models of devices that are used by most customers. Few people take options without Wi-Fi, because, as a rule, the device is purchased for it. Setting up the router Beeline dir occurs in two stages: physical connection, connection control via browser. First you need to make sure that the network card is installed latest version firmware. This applies more to owners of older computer models. The configuration is then carried out as follows:

Unpack the device, connect the power supply and cord to the connector labeled “WAN”. Connect the second cord to one of the additional inputs and connect it to the computer.
Next, set up the connection in the Start menu. Go to “Control Panel”, here click on “Network and Sharing Center...”. Click Adapter Settings. Set the line to Internet Protocol Version 4, then click “Properties”.
Make sure that items with automatic issuance of IP and DNS servers are active.
Next you need to go to internal interface. To do this, in any browser, enter “192.168.1.1” into the site address field. A form for entering your login/password will be displayed to log into the admin panel. To go inside, you must enter the word “Admin” in both fields. These are factory access options, if they do not fit, it means they have been changed. You can reset the values by pressing Reset button on the device. You should hold it for about 10 seconds.
When you log into the back-end interface, select “Configure manually.” Next, go to the “Network” tab, click “Add”.
Select the connection type - L2TP, dynamic IP.
Enter your Beeline-issued login and password into the appropriate fields.
Check the boxes next to “Keep Alive” and “Connect automatically”. Click "Save".
Click “Save” again. Next will happen automatic connection. To find out if the network is working properly, just go to any website from your phone.

Setting up an Asus Beeline router

Another popular device manufacturer is Asus. There is no program on the disk to automatically connect to the network, so you will have to do everything manually. Carry out setup Asus router Beeline is needed as follows:

Connect the device to power, network and computer.
Open your browser, write 192.168.1.1 in the site address bar, press enter.
To access, enter the password and login “admin”.
In the internal interface, click on the “Advanced Settings” tab, select “Wan”. Next, specify the following data: “Connection Type” - “L2TP”, “Get the WAN IP automatically” - “Yes”, “Connect to DNS Server automatically” - “Yes”, “ VPN Server" - "tp.internet.beeline.ru". In the login/password fields, indicate the access granted by your provider.
For turn on Wi-Fi go to the “Network Map” item.
A table will appear on the right for quick configuration wireless connection. You need to configure it as follows: “Wireless name” - specify/create a name home network, “Security level” - “WPA-Auto-Personal”, “WPA Encryption” - “TKIP+AES”. On the “WPA-PSK key” line, write the Wi-Fi password. Click the “Apply” button.

Setting up a TP-Link router for Beeline

This is a popular model due to the presence of an installation wizard that is able to connect to the network independently. As a rule, a disk on which the program is located is sold along with the device. You just need to connect the router to your computer, insert the CD and launch the application. If the connection does not open, you need to do everything yourself. Setting up a TP-Link router for Beeline is carried out as follows:

After connecting the device, go to the browser, type in “192.168.1.1”, press “Enter”. Enter the login/password “admin”
Open the “Network” tab and the “WAN” item.
Specify the connection type “L2TP”, enter the login/password issued by your provider (Beeline), IP server – “tp.internet.beeline.ru”.
Specify automatic connection (“Connect Automatically”), MTU size– 1400. Click on the “Save” button.
To enable the Wi-Fi network, go to the “Wireless” section and click on “Wireless Settings”.
Come up with a name for the network, specify the region “Russia”, channel and mode – “automatic”. Click the “Save” button.
Next, go again to the “Wireless” section, click on “Wireless Security”.
Here, activate the “WPA-PSK/WPA2-PSK” item, then set everything to “automatic” mode. Create a password for the connection and click “Save”.

Setting up a Zyxel Keenetic router for Beeline

Some users prefer Zyxel. The physical connection of the router is carried out in the same way (a wire to the WAN connector and a second one to the computer’s network card). The intranet setup of the Beeline keenetic router is as follows:

Type 192.168.1.1 in your browser.
Enter “admin” as your login/password.
Go to the “Internet” section, click on “Connection”.
Specify the following values in order: think of any name for the Internet center, configure IP parameters and getting DNS set it to automatic, check the box to respond to ping requests and enable UPnP. Click on "Apply".
Next you need the “Authorization” tab. Do not check the first box, the protocol should be L2TP, the server address should be tp.internet.beeline.ru, write down the login and password in the given access lines. Save your changes.
To activate Wi-Fi, open the “Wi-Fi Network” section, the “Connection” section.
Check the box to enable the access point. Come up with a network name, the SSID field should be left blank, the standard is 802.11g/n. The next two items should be in “auto-select” mode, then leave everything as is. Click on “Apply”.
Go to the "Security" tab. Set authentication to WPA-PSK/WPA2-PSK, security type to TKIP/AES, format to ASCII. Create and write a password for access. Click "Apply".

Video: Beeline Smart Box router - setup

Access to worldwide network All cellular companies offer it, but Internet access from the Beeline provider is considered one of the most popular options. The operator provides its consumers and how Mobile Internet, operating according to the 4G standard, and home.
To get wireless Wi-Fi coverage, branded routers from other manufacturers are used, the settings of which vary depending on the device model. Our article today will tell you exactly how to connect a Beeline router.

Contents of the article

1 Setting up a router from Beeline
2 How to set up a router D-Link DIR-300
3 Asus devices
4 TP-Link devices
5 Zyxel devices
6 Conclusion

Setting up a router from Beeline

If several computers are used in one house, then setting up Wi-Fi becomes more than relevant. Wireless Internet access is extremely convenient when working with modern smartphones, tablet PCs or laptops. Setting up Internet access through a router can be done automatically or manual modes, which directly depends on the model of the device used.

Basically, when signing an agreement with the Beeline provider, a company specialist comes to the new client’s home and sets up the correct connection. But if Wi-Fi router was purchased later, or the device was replaced, the connection will need to be configured again.

Each router has its own guide for entering settings, but the individual steps are absolutely identical for all devices, for example:

Connecting the cable to the router itself.

Connecting the second cable directly to your laptop or PC.

Entering the correct settings (device address, type of connection used, setting a password, etc.).

Router connection diagram

How to set up a D-Link DIR-300 router

There are such famous models routers that are used by the majority of all consumers. This is exactly the model DIR-300 is. Few subscribers choose devices without Wi-Fi, because, basically, this is the only reason the model is purchased.

Settings D-Link devices DIR is carried out in two stages:

Physical connection (Fig. 1).

Control created connection via browser.

First you need to make sure that the network adapter The latest driver version is installed. This mostly applies to owners of old PCs.

You need to unpack the device and connect the power supply to it, and then connect the cable to the port labeled WAN. The second cable connects to any LAN port on the router and, accordingly, to the computer.

Next, the subscriber needs to open the “Start” tab on the PC and go to the “Control Panel” section, and then enter the “Network Control Center”. Here you need to click on the “Adapter parameters” column and set the protocol version to line “4”, and then open “Properties”.

The user needs to make sure that the “IP” and “DNS Server” items are in the “Automatic” mode.

Then the subscriber needs to go to internal menu. To do this, you need to enter the value 192.168.1.1 in the browser line and confirm the transition. will appear special form, in which you need to enter your login and security password. To get to the admin panel, you need to enter the word “Admin” in both lines. This is the factory method for gaining access.

In the interface that appears, select the item “ Manual settings", enter the "Network" section and press the "Add" button.

Then set the connection type to “L2TP”, and set the IP to “Dynamic”.

In the fields that appear, enter the client login and security password. They are issued by Beeline when purchasing a router.

Then you need to check the boxes next to the items “ Automatic connection" and "Keep Alive", and then press the "Save" key.

Press the “Save” button again, after which the connection will be made in automatic mode.

That's it - the router is configured.

Asus devices

Another famous manufacturer routers – Asus company. The disk included with the device does not contain a utility for obtaining settings automatically, and therefore the subscriber will have to enter all the parameters manually.

ASUS router

You must enter the settings for the Asus router as follows:

The device must be connected to the network and connected directly to the PC using the included cable.

Then you need to open any browser and enter the value 192.168.1.1 into the search bar, and then press enter.

To gain access, the user needs to enter a login and a security password - the word “Admin” must be entered in both fields.

After entering the internal interface, you need to go to the tab called “Advanced Settings” and select the “WAN” column. Then set the connection type to “L2TP” and make sure that the “IP” and “DNS Server” items are in the “Automatic” mode. In field " VPN Server"We register the following address - tp.internet.beeline.ru. You also need to enter own login and a security password - they are issued to the subscriber when purchasing a router.

To activate Wi-Fi you need to go to the “Network Map” tab.

WITH right side A table with the configuration for a quick wireless connection will appear. The following parameters must be entered here: “Connection name” – come up with any name; “Protection type” – WPA auto; “Encryption WPA” – enter “TKIP+AES”. In the “Password” field, you need to enter any one you come up with, if necessary. Then click on “Confirmation”. Now the router is fully configured and ready to go.

This completes the configuration of the router for Beeline.

TP-Link devices

This device model is quite popular and in demand due to the fact that it has an installation wizard that can connect to the network automatically. Basically, a disk is supplied with the router, on which the master is located. The user only needs to connect the device to the PC, insert the disk into it and launch the installation wizard. If according to unknown reasons The connection could not be established, then there is only one way out - entering parameters manually.

Router TP-Link

The device is configured as follows:

After connecting the router to the PC, the subscriber needs to go to any browser and enter the value 192.168.1.1 in the line, and then press enter.

Next, go to the “Network” tab and open the “WAN” column.

Then we set the connection type to “L2TP”, enter our login and security password, which was issued by the provider when purchasing the router, and for the IP server we enter the following address - tp.internet.beeline.ru.

We indicate “Automatic connection” and for “MTU” we set the value to 1400. Then press the “Save” button.

To activate Wi-Fi, you need to go to the “Wireless” section and open the “Settings” column.

Next we come up with a name for the network being created, set the region to Russia, and also set the “Channel” and “Mode” items to “Automatic”. Click on “Save”.

Next, go to the “Wireless Security” section and activate the “WPA-PSK” item. For all other items, set the value to “Automatic”. Press the “Save” button. The router is now fully configured.

Zyxel devices

Some customers prefer to use devices from the manufacturer Zyxel. Let's look at how to set up a router from this company. They connect to the computer in the same way as the above devices. And here internal setting carried out in this way:

Zyxel router

Go to the browser and enter the value 192.168.1.1 in the line.

In the fields for login and security password, enter the word “Admin”.

Then go to the “Internet” tab and click on the “Connection” column.

Next, fill in the following items: name of the Internet center - enter any; Set the “IP” and “DNS Server” items to “Automatic” mode; Opposite the “ping requests” item, check the box and set the UPnP value to “Allow”. Click on the “Apply” button.

Then go to the “Authorization” tab and set the connection type to “L2TP”, and for the server we register the following address – tp.internet.beeline.ru. In the login and security password fields we enter the access that was given when purchasing the device. Click on the “Save” button.

To activate Wi-Fi, you need to go to the “Wi-Fi Network” section and select “Connection”. Then check the box next to “Connection points” and come up with a name for new network. The field called "SSID" is not filled in. We set the standard to 802.11g/n. We switch the next two sections to the “Automatic” mode. Click on “Application”.

Next, go to the “Security” tab and set the value to “WPA-PSK” for authentication, and set the value to ASCII for the format. If necessary, we come up with a password for the network. At the end, click on the “Apply” button. Now our router is fully configured and ready for the first connection.

Conclusion

We have considered all the most popular models routers for Internet access from cellular company Beeline, and also talked about how to connect them and configure them correctly.

In fact, setting up a Beeline router should not cause any problems for users. All that is needed is just to repeat all our actions in practice and a positive result will not take long to arrive.

Let's consider this action using the example of settings on the most popular OS.

Setting up a network card

We carry out the installation ip addresses . To do this, go to “Start”, then go to the “Control Panel” section and select “Network Connections”.

Right-click on the section this menu"Connect via local network" - select "properties" in the drop-down menu, click on "Internet protocols TCP/IP" and select "properties" again.

Check the boxes where the word “Automatic” appears and save the changes.

After completing these steps, you can begin connecting the Beeline router.

How to set up a wifi router d-link dir 300 for Beeline

Enter - admin in both lines, this data is standard for everyone. You can change them later if you wish.

Now you will accessible page settings, it is better to give preference to selecting the function manually. To enter the desired menu, click on the “Advanced settings” link.

On the page that appears, select “WAN”.

The following sections must be completed:

connection type - L2TP Dynamic IP;

user - the login that was created for you when you connected to the Beeline Internet will definitely be in your contract;
password - the password that was created for you when connecting to the Beeline Internet must also be in the agreement;
VPN server address - write the following: tp.internet.beeline.ru.

Then you need to click the “Change” button.

Go to the “Advanced Settings” section again, select WI-FI - then “Basic Settings”. In the “SSID” line, enter the name of your Wi-Fi network and click “Change”.

Note! If you want to password protect your network, returning to the previous menu, click on “Security Settings”. Opposite the “authentication” section, enter WPA-PSK2, “key” - own password. (This is the most common security connection and will help you protect your network from hacking and unauthorized use of the Internet.)

How to set up a tp-link wifi router for Beeline

To set up tp-link router for Beeline, you should enter one of the addresses to choose from - 192.168.0.1 or tplinklogin.net into the address bar.

Select the Network section, and in it the item - WAN.

On the page that opens, opposite the line “WAN (Connection Type), you need to select L2TP/Russia L2TP, in the “user name” and “password” fields, enter the data specified when connecting to the Beeline Internet.

Then in Server IP Address/Name enter tp.internet.beeline.ru. Be sure to check the box next to Connect automatically.

Save your changes.

After this, the Wi-Fi network will be available for you to use.

How to set up a Beeline routerSmart Box

First connection router, you can use a cable or make settings using wireless communication Wi-Fi. The network address will be default - 192.168.1.1

Open Beeline Smart Box.

On this page you need to click on the “Continue” button, this will help you get to the authorization section.

Before installing Beeline router Smart Box, click on the clickable button “ Quick setup", after which a window will appear containing all the basic connection parameters.

In the field opposite the “Login” line, you must enter the contract number concluded with the provider, “Password”.

If you have lost the data required for authorization, please contact service center Beeline - after confirming your identity, the operator will give you necessary information.

After completing all these steps, click “Save”, and immediately click “Reboot”.

The router is connected, you can start setting up Wi-Fi networks. To do this, you need to go to Smart Box.

Select the section “Advanced settings”, which will allow us to go to the expert settings Smart settings Box. Click on the “Wi-Fi” section, in the menu of which we select the first item – “Basic parameters”.

To increase network security, the “Authentication” line should be set to “WPA-PSK”.

Wi-Fi routers from Beeline have everything greater demand among active users networks. Setting up a router only looks like it at first glance complex process. In fact, anyone can cope with the connection and settings using special tips.

Proper connection of a Wi-Fi router

If you want to save money, you can connect and configure your Beeline router yourself. To do this, you first need to connect the patch cord at one end to LAN port on the router, and others - to network card your computer. After this, you need to open the browser that you usually use, and in the window that opens address bar enter the IP address number. It is standard for everyone: 192.168.1.1.

A special window should pop up on the monitor in which you need to enter your login information and password. Please note that this data may be indicated in the instructions for the router. If you do not find them, then you need to enter the standard combinations for all: login - admin and password - admin. After that, click “Login”.

Setting up a Beeline Wi-Fi router

The setup is done by entering the “Setup -> Basic Settings” menu. Here in the “Server Address” column you should enter tp.internet.beeline.ru, in the “Connection Type” item we indicate L2TP, and the MTU is set to 1400. After that, we save all the selected settings, the waiting time will be no more than a minute.

Now you need to configure your wireless network. This must be done manually by entering the menu and selecting “ Wireless network-> Basic settings". Here you need to fill in all the parameters as follows:

“Network name” - indicate the name of your network.
“Transfer SSID” - check the enable box.
In “Network mode” select “Mixed”.
The “Channel Width” parameter is set to automatic.

How to update a Beeline router

Updating a router involves updating its firmware. To do this, just download it from the Internet. Then we follow a few simple steps. Select the path “Administration -> Firmware Update -> Overview”. Here you need to select the firmware file that you previously downloaded to your computer and click the “Start Upgrade” button. After a short wait, a window should appear indicating that the update is complete.

The mobile operator Beeline at one time acquired the business of one of the major players in the Internet provider market, so today its subscribers in the provision of high speed connection are millions of users. Therefore, I decided to write this step-by-step article on setting up a Beeline router, which describes an Internet connection using the L2TP protocol and can be used for any model, regardless of manufacturer - Asus, D-Link DIR, TP-Link, Zyxel Keenetic and so on. The only differences may be in the layout of settings functions and menu headings in the device admin panel.

We find it on the router WAN port of blue color(if it has color). We insert a cable into it from the Beeline Internet provider, which was previously connected directly to the computer. Next, we find one or more yellow LAN ports there. We insert into one of them network cable out of the router box. We insert the other end into network card on the computer.

Turn on this PC or laptop and go to the section: Start > Control Panel > Network and Internet > Network and Sharing Center and shared access> Management network connections> Changes adapter settings.

There will be one or more icons for network connections; we need “Local Area Connection” from them. Call up its settings menu by clicking right button mouse and go to “Properties”

There is such a section as “Internet Protocol Version 4” - check the boxes to receive IP and DNS servers"automatically".

Save the changes with the button.

Setting up a router on the Internet from Beeline

We return to the computer and type the IP address from the label in the address bar of the browser.

We find in the router menu the section responsible for connecting to the Beeline Internet - it can be called Internet or WAN

In the Type column WAN connections select “L2TP”
WAN IP address - automatically
DNS - automatic

In the “Server” section we write “tp.internet.beeline.ru”
Username and password - we indicate from the agreement with Beeline.

Save the settings and reboot the router.

Configuring a Beeline router to broadcast a wireless signal

Finally, all that remains is to configure WiFi. Open the “Wireless Network” section in the menu and set eigenvalues For:

- the name of your wifi networks, which will be displayed in the connection list
Network security method - WPA2-Personal