How to update tricolor TV channels gs 8306. Receiver firmware via USB service port. Distribution from flash card

Update gs 8306 what it brought.

The gs 8306 update immediately began to show its character. Literally after a while, we saw a message on the receiver’s screen - error 0. What’s interesting is that there is sound, but no image!

Good that this problem can be treated with a simple switch.

gs 8306 update

When switching, you can observe long running diamonds, while the old p.o. already showing. Of course, this doesn’t happen all the time and sometimes the new one even switches faster.

gs 8306 receiver update

There are of course advantages, for example the new kind information. New menu.

update software gs 8306

New services for this receiver may of course be good, but are these innovations necessary? Especially when the receiver began to experience constant freezes?

update

For example, the receiver may reboot on its own. After it turns on, it will show on the screen - no signal.

no signal after update

You go to the menu, to the list of programs. Everywhere there will be a problem with the antenna. Take your time to check the antenna, everything is fine with the antenna. We reset it to factory settings and configure it anew. The receiver starts working until the next glitch.

This is all strange, of course, the receiver is working. There is payment. What else does an operator need? Apparently we don’t know... This makes all the difference, the subscriber needs the receiver to work. It turns out that the operator does not need payment, they need to change the receiver.

How else to think? Of course, the switching mode is good, the backlight of the diodes has been changed - good! Now the flashlight has been removed and the receiver does not light up at night. But now there is a lot of advertising, a message - no signal, reboot.

Do you think this is good or bad? At the same time, NAO NSK again says that FIPS Code: 393963 has nothing to do with it, the partners are to blame.

Of course, new po. possible and good. But after this update, people need to watch TV instead of running to the outlet and rebooting the receiver.

The reboot speed of the receiver is also excellent!

While it is rebooting, you can do sports, for example, jumping with a tambourine...

This article should be useful to subscribers satellite operator Tricolor TV who purchased sets satellite equipment Tricolor TV with receiver GS 8306 (8305), software version V 1.0.049.

These kits, packaged in branded boxes, can currently be found mostly on the shelves of chain stores, the names of which we will not mention, but buyers turning to this article will remember the names of these stores, including with an unkind word.

In March 2013 the software of this receiver model was updated via satellite, however, the kits that were on store shelves at that time, and as you understand, were not connected to satellite antennas we simply did not receive the same update package version V 1.1.001 necessary to watch channels in HD format.

As stated by the Tricolor TV company itself, GS 8306 receivers that have not received the update package will not be able to provide access to viewing channels in HD format.

Exits from this provision some:

1. Wait next update via satellite for the GS 8306 receiver model, but no one can say with certainty when it will happen.
2. Contact service center asking to change the software version, but this is a costly method.
3. Update the receiver software yourself by downloading the firmware from our website in the section or by rummaging through the “Help” menu on the main website of the Tricolor company.

Below we present the sequence of actions that you will need to repeat in order to change the software on the GS 8306 receiver:

1. To install the firmware, you need a flash card, which you can find at home or buy, or temporarily borrow from your friends or relatives. Please note that not all flash cards are compatible with the GS 8306 receiver, so we recommend that you find a card from Transcend; it was the flash card from this company that our company repeatedly updated the software of the receiver of this model.
2. After you have acquired a flash card, you need to format it in FAT-32 and make sure that there are no damaged blocks on the card. If there are damaged blocks, we replace the flash card.
3. Copy the file ssu_gsc_stb.upg to the root directory of our formatted flash card without changing the file name.

4. Before inserting the flash card into the receiver, you need to make sure that the receiver is turned off, it is advisable to unplug the receiver's power supply from the outlet.
5. With the receiver turned off, insert the flash card into the connector for USB storage, located on the rear panel of the GS 8306 receiver.

6. Plug the receiver's power supply into a power outlet and press the round receiver power button located on the front panel of the receiver body. Sometimes to turn on the receiver you need to hold down the power button for 2-3 seconds, so we immediately recommend that you hold down this button so as not to make further attempts to turn on the receiver.

7. After a few seconds, you will see the LEDs surrounding the power button begin to blink alternately, and on the TV screen you will see a frame with the inscription “Please wait, the software is being updated.” The scale will gradually fill, which means the software update process is moving forward.

Remove the flash card from USB connector It is strictly prohibited to open the receiver's drive until a message about the completed update appears, otherwise you risk the receiver failing and requiring you to contact a service center.

8. After the entire scale is filled green, and on the screen you will see the message “Update completed successfully! Please turn off USB storage and reboot the receiver." All you have to do is remove the flash card from the USB drive connector and use the power button on the front panel of the receiver to turn off the receiver.

9. Again, use the power button on the front panel of the receiver to turn on the receiver and enjoy watching channels in HD format that were unavailable from old version software V 1.0.049

If you still have any questions, you can ask them by calling our company Kirovsat t. 44-13-50, t.s. 8-912-734-13-50 or in our store at Kirov, st. Svobody, 130 Shopping center "Mayak" (near the Central Market).

Question answer

Question: How much does Tricolor TV cost you?
Answer: A set of equipment for viewing Tricolor TV channels with the new GS 8307 Full HD receiver costs 7,900 rubles. This equipment allows you to receive more than 170 channels. Of course, the price of the first year of viewing is included in the price of the set. If you want to watch even more, buy it additional packages operator Tricolor TV. Price standard installation– 1000 rubles.

Question: Where can I buy a Tricolor kit in Kirov and order installation?
Answer: Call the Kirovsat company phone numbers 44-13-50, 8-912-734-13-50 and report the model of satellite equipment that you have decided to install and the installation address. Choose the most suitable delivery and installation time for you. After installing and configuring the equipment, pay the installation fee and the cost of the equipment.

Question: What do customers most often choose now?
Answer: Most often you have to put Tricolor and Telecard.

Question: My old antenna was blown away by the wind and the wires were broken, cost new setting and the installation will be the same - 1000 rubles?
Answer: No, you will have to pay much less to restore normal channel viewing. We offer significant discounts to customers whose antennas are already installed.

Question: I don’t know if it is possible to install the antenna near the balcony or window. Is there a satellite signal?
Answer: Contact us and give the exact address indicating where the windows face. In most cases this is possible.

The Tricolor GS 8306 receiver may not turn on for many reasons. Most operator receivers have similar faults.

A characteristic feature of the GS 8306 is the lack of a display. Switching on and off is identified by two LED bulbs. The operator has other set-top boxes that do not have digital panel, for example: GS B211, GS B520.

In order to understand the nature of the malfunction, it is necessary to perform full check technology. Since problems with the device can arise for a number of reasons.

1. Power problems.
2. Malfunction and breakdown.
3. Incorrect software installation.
4. Hardware settings failure.

These are the main reasons why the receiver model GS 8306 of the Tricolor operator does not turn on.

How to determine the source of problems

In order to find out why the set-top box does not work, you should study each possible factor in detail.

Power supply

If the Tricolor receiver does not turn on, then the first thing you need to do is check the power supply to the equipment:

• serviceability of sockets;
• Is the power adapter connected to the outlet correctly?
• whether the connecting cables are connected to the device.

Control panel malfunction

Another common problem is that the device may not turn on due to a faulty remote control. The receiver may not respond to pressing keys on the remote control, possible reason– battery wear. If after replacing the batteries again Tricolor receiver does not turn on, it is recommended to contact a service center to troubleshoot or replace the remote control.

There is no picture on the TV

If there is no picture on the TV or the picture freezes, it is necessary to exclude operation in standby mode Stand By, It is also recommended to check whether the wires are connected correctly.

“No Signal” message appears on TV

If the following message appears on the screen: “No Sound”, “No Image”, this means that the tuner is receiving a weak signal.

• The satellite dish cable is damaged;
• converter failure;
• there is an obstacle in the signal path.

The device does not turn on after a software update

If the set-top box does not turn on after a software update, then this is most likely the result incorrect installation or errors. It is recommended to return the old settings.

1. Press the “Menu” key on the remote control, then select the “Settings” tab ↦ “Reset” ↦ “Reset settings”. You should click the “OK” button.
2. When prompted to enter a password, enter four zeros, then the device should reboot, the equipment will turn off and on.
3. After the reboot, a request for settings will appear on the TV screen, click “OK”. Select your provider and click “OK” ↦ select a region, click “OK”.
4. After the channel search procedure is completed, a notification about the completion of the search will appear on the TV screen.
5. You need to save the channels by clicking “Save” and then “OK”.

Due to these faults, the GS b211 may not turn on.

Causes of problems with other popular models of Tricolor consoles

Model GS 8300

The main causes of malfunction of the GS 8300 receiver are identical to other operator devices. But the GS 8300 has a feature; users often notice that the receiver can constantly turn on and off automatically. The reason may be in the firmware or the power adapter is faulty. The device may also turn off due to the connecting elements coming off. Also, this successor can reboot, reset and boot again.

Main reasons:

• problems with the cable or f connector;
• The power supply has failed.

Model GS 6301

One of the main reasons why the GS 6301 receiver may turn off is outdated software. To update it, you need:

1. Download updated firmware to a flash drive.
2. At the same time produce complete shutdown devices from the network.
3. Insert the drive, and then turn on the receiver.
4. An update will occur, you need to remove the flash drive.
5. Afterwards, the first installation will begin on the TV monitor, you need to click “OK”.
6. Wait for the channel list to update and confirm it.

If the receiver still turns off after updating the model, it is advisable to contact a repairman.

These are the main reasons why the Tricolor TV GS 6301 receiver does not turn on.

What to do if the tuner does not find Tricolor channels

If you can’t find channels, the reason may be the following:

1. It is necessary to reflash the device.
2. The antenna convectors do not have enough power.
3. The smart card is inserted incorrectly.
4. The equipment is not connected well.
5. Subscription not paid.

If, after eliminating these factors, the equipment does not find the channels, it is recommended to contact a service center.

Guarantee

Repair your faulty receiver free of charge service possible within a year. The warranty period starts from the date of purchase. If the cause of the malfunction additional elements: remote control, cable, then the warranty period is 6 months. You can activate an electronic guarantee on the Tricolor website; in such cases, you do not need to present a receipt or paper coupon.

You can also check the warranty period on the operator’s website; to do this, you need to enter the set-top box code in a special field. The warranty does not apply to the smart card, or if the breakdown occurred due to the fault of the buyer.

On the website of the equipment manufacturer for Tricolor appeared The new software for the GS 8306 receiver is firmware version 1.9.160.

This firmware was intended to replace software version 1.2.001, released several years ago. It must be said that firmware version 1.2.001 for the GS 8306 is exactly the software with which the GS 8306 receiver began to work more or less normally and stably - it did not freeze, the picture practically did not freeze, the channels switched quite quickly. With firmware 1.2.001, the GS 8306 receiver had only one problem left uncured - the external 12v, 2A power supply could fail, but the problem was solved by purchasing another unit at a price of 500-700 rubles. And even the above problem is not very common with the GS 8306 model.

And now, after several years of successful operation of the receiver with proven and proven firmware, for some reason it was necessary to release new software - version 1.9.160.

Well, they released a new firmware and released it. Usually, after updating the software, Tricolor receivers begin to work more stably. There was an expectation that even after updating the firmware to 1.9.160 everything would be fine.

The website of the manufacturer of the GS 8306 model states the following: characteristics new firmware(see screenshot below):

Changes compared to previous version software:

1. Modern GUI Stingray software
2. Improved receiver stability
3. Added functionality manual search channels
4. Improved operation of the Tricolor TV Cinemas application

Description of the characteristics of the new version of software for the GS 8306 receiver - version 1.9.160 Picture - screenshot of the page at - http://gs.ru/support/manuals-and-software/gs-8306/

I would like to convert Special attention to point No. 2 of the description of the new firmware - the stability of the receiver has been increased!!!

In practice, we encountered the following problems when flashing and after flashing the GS 8306 receiver to version 1.9.160

1. The receiver is sewn over the air and if you confirm the completion of the firmware, it may not be successful - the firmware process freezes and the receiver remains in an unflashed state. At the same time, the old firmware has already been erased. That. the receiver turns into a brick. Further restoration is only possible by unsoldering the flash memory chip, flashing it in the programmer and soldering it back into the receiver. This is a relatively expensive procedure.
2. Another problem with flashing is the long duration of its execution. People are starting to get confused about whether the firmware has already been completed or whether the procedure is still ongoing. Confused and unable to stand it, many of them, out of impatience, disconnect the receiver from the power supply and if the firmware has not yet been completed, then the receiver again turns into a brick.

Those subscribers who were lucky and whose receiver, after several hours, was successfully updated to 1.9.160 will have to face other problems in the operation of the receiver, which previously worked stably.

1. The message “no signal” appears periodically when viewing channels. After such a message, you can switch to another channel, watch it for a while, return to the channel on which the “no signal” message appeared and continue watching the selected channel again for a while. But only until the next time the “no signal” message appears.
2. From the description of the new firmware it is clear that it has received a “modern graphical interface for the Stingray software.” So, the needs of this very Stingray, according to our subjective feelings, exceed the capabilities of the processor and memory of the GS 8306 receiver. This leads to the fact that channels now switch much longer than before - not old firmware 1.2.001.
3. When switching channels, especially when switching channels of different thematic packages, some receivers simply reboot.
4. Pink tint to the image after turning on the receiver. Some users actually encountered the problem that after the firmware all their channels are shown in pink color. Although, maybe it’s good to look at the picture in pink in our 21st century. The problem is eliminated by overloading the receiver's power supply.
5. The picture may freeze terribly on some channels. On our test receiver, the “Match HD” channel, number 103 in the channel list, especially freezes.
6. If after the firmware the receiver has not turned into a brick and continues to function at the very least, then flashing it back to stable firmware 1.2.001 via the USB port will not work - it is blocked
7. Periodically, the receiver reboots on its own even without any action, such as changing the channel
8. The audio and video tracks are periodically out of sync
9. From time to time the receiver simply freezes, especially when it experiences some kind of load, for example, when switching channels.

These are, perhaps, the main points that owners of the GS 8306 receiver on the new firmware 1.9.160 will encounter. And in our, again, subjective opinion, most of the listed problems are related to the fact that the hardware power of the GS 8306 receiver is not enough to satisfy all the needs of the new Stingray software.

In light of all the identified operating problems with the new firmware 1.9.160, one can only guess what increase in the stability of the receiver the software developer is talking about.

Now let’s talk about how to continue using the receiver on firmware 1.9.160

This is what we personally did with our own GS 8306 receiver to improve its stability. This is the method that was recommended by colleagues who encountered and dealt with the problems of firmware 1.9.160 before us - to increase the stability of the receiver with the received signal, it is necessary to set the frequency (lower and upper) of the local oscillator to 1 MHz higher than the standard value - 10751 MHz versus the standard 10750 MHz

After the local oscillator frequency was set to 10751 MHz, the receiver stopped displaying the “no signal” message when viewing channels and began to work more stably when viewing and switching channels. It is already difficult to do anything more.

What else do you need to know when operating the GS 8306 on firmware 1.9.160

The new firmware has changed the operating mode of the receiver. Now the receiver automatically determines which video output the cable connecting to the TV is connected to. Depending on which video output the firmware detects the connection cable to that video output, it will send a video signal. In the case when 2 cables (HDMI and 3RCA) are connected to the receiver at once, confusion may arise and the receiver will not understand which video output to send the video signal to. Therefore, at one time we connect only one video cable to the receiver.

One more point is light indication on the receiver. Previously, the top lit indicator meant activity HDMI output set-top boxes, then on firmware 1.9.160 the glow of only the top indicator means that the receiver is in standby mode and to start watching it must first be turned on. And after turning on, the receiver will automatically send a video signal to the detected video output.

Download firmware 1.9.160 for GS 8306

If you really need it, then the “wonderful” firmware for the GS 8306 receiver can be downloaded from the official website of the manufacturer of this receiver at http://gs.ru/support/manuals-and-software/gs-8306/

P.S. — After lengthy problems with mastering the new firmware for the 8306 receiver, a number of questions arose:

1. Why was it necessary to write new software for the receiver if the old one worked stably and with virtually no complaints?
2. when will new software appear that will fix all the problems and bugs in version 1.9.160

We update GS 8306 from USB to the new version 1.9.160, beginning

GS 8306 has waited its turn and we are updating it via USB. For this we have a new version software 1.9.160. Let's see what difficulties there may be during pouring. Because unfortunately updates on the operator's receivers Lately don't go very smoothly.

GS 8306 version p.o. 1.9.160

GS 8306 update process

2. The receiver begins the update process. The entire button is lit, but there is no image on the screen! It is impossible to check the update process on the screen; both receiver outputs do not work!

GS 8306 version p.o. 1.9.160, upper diode.

3. One diode of the receiver lights up constantly, the second blinks occasionally. This is all normal, the main thing is not to turn off the receiver from the network! If you turn off the power now, the receiver will fly far and long!

GS 8306 version p.o. 1.9.160, the update process is complete.

4. After the receiver has loaded everything, both diodes will go off! We wait at least 10 seconds. If you turn it off earlier, the receiver will be damaged! Of course, it’s scary, but that’s how everything is done here….

GS8306 p.o. 1.9.160 switching on.

5. After everything has been updated, turn off the receiver from the network. We remove the flash drive from the USB. Turn on the receiver and configure all programs.

GS8306 version p.o. 1.9.160 status check.

That's all, we have updated our receiver, now we can watch television programs. The main thing to remember is that during the update our receiver may break and this is not a joke. The majority of users will not be able to repair the receiver themselves.

If you still have doubts about how to update, watch the video. In this video, the entire update takes place in real time.

Let's add another video about this firmware.