Menu
homeExcel

The best free programs for repairing flash drives. Recovery of Transcend USB flash drives

to restore the functionality of self-produced flash drives (A-DATA, Transcend and JetFlash), the file system of which has been damaged. The functionality of the media is restored by completely formatting it. The utility also scans the drive for the presence of non-working (bad) sectors and marks them as such so that the controller no longer accesses these sectors while recording information.

JetFlash Recovery Tool destroys all data on the media during scanning.

However, if the memory block is damaged or the flash drive fails, the utility will not be able to restore it. Before performing any manipulations with the flash drive using the JetFlash Recovery Tool, make an image (an exact copy) of the file system of your drive, if possible. Information can be recovered and safely retrieved from it. One of the distinctive features of the JetFlash Recovery Tool utility is its low system requirements:

  • Processor with a clock frequency of 800 MHz.
  • RAM from 256 MB.
  • Free hard disk space from 7 MB.
  • 32-bit or 64-bit architecture (x86 or x64).
  • Operating system Windows XP and newer versions.

As you can see, the utility will work on any modern computer. The universal utility JetFlash Recovery Tool has a number of useful features:

  • supports JetFlash, Transcend and A-DATA flash drives;
  • supports the most common file systems: Ext4, XFS, ReiserFS, FAT32 and NTFS;
  • recovers flash drives that the PC is unable to detect;
  • restores the working condition of flash drives that are not working correctly;
  • restore information if the media is partially damaged;
  • Supports card readers and removable hard drives that are connected via USB.

You can download JetFlash Recovery Tool for free from the developer’s official website using this link. The program works in several steps and is as follows. We launch the application after connecting a USB drive that is not detected or is identified as an unknown device, and click “Start” to carry out the procedure for identifying it.

We wait for the drive to scan, which is completed in a matter of seconds.

Your USB drive will be displayed in the window that appears. If you are ready to say goodbye to all your data or spend a lot of time restoring them if the flash drive is successfully resuscitated, click “Start” to start the procedure for restoring the logical structure of the USB drive.

The program will display a message stating that during scanning all data on the drive will be lost. If you agree, click “Ok” and wait for the drive recovery process to complete.

Do not interrupt the program under any circumstances (removing the flash drive, turning off the computer, interrupting the utility are contraindicated), as you can lose the flash drive and all its contents forever.

After a few minutes, the application will display a message indicating that the drive has been restored. Click “Ok”. We disconnect the flash drive and then connect it again to check its functionality. The device will work properly if the JetFlash Recovery Tool has coped with its task perfectly. How could there be a slight loss of useful memory, depending on the number of damaged sectors? This happens due to the decommissioning of some damaged sectors. Sometimes after completing the first step (starting scanning your computer for removable USB drives), a dialog box appears with a message stating that the utility was unable to detect your USB device. This means that your flash drive was made by a company other than Transcend, and the utility does not work with third-party drives.

Close the dialog box and select another program to restore the flash drive.

Video instructions for restoring a Transcend flash drive using JetFlash Recovery Tool

JetFlash Recovery Tool (JetFlash Online Recovery) is a compact program for working with USB flash drives from Transcend. This utility has 2 main uses. The first is related to restoring the functionality of the USB drive, and the second is related to removing write protection from the flash drive.

JetFlash Recovery Tool has a simple and user-friendly interface. Even if you don’t know English, you can easily understand the basic features of the program. When you launch the utility, you will be asked to insert a USB flash drive from Transcend and connect to the network. Once these requirements are met, a list of all available flash drives will appear on the main screen. Select your USB drive and go to the action menu. If the device is successfully identified, 2 buttons (Start and Exit) and the option Repair drive and erase all data will be displayed here. When you click the Start button, the program will check the USB flash drive for errors, start the procedure for formatting the device’s file system and restore the area with damaged sectors. This entire process will take from 1 to 5 minutes. Also, in some cases, you will have another option available – Repair drive and keep existing data. With its help, you will restore the working state of the flash drive, and at the same time all existing data will remain intact.

If you have a non-working flash drive from Transcend, then do not rush to get rid of it, because there is always a chance of successful recovery of the USB drive. You just need to use the JetFlash Recovery Tool program, and with a high degree of probability you will be able to bring your USB device back to life.

Key Features and Functions

  • the presence of a recovery function for a damaged Transcend flash drive;
  • the ability to run the program without installation;
  • ability to connect to a large firmware database.

By downloading free programs for repairing flash drives, you can restore the USB drive and regain the ability to use it for writing and reading. In this case, you will have to sacrifice data, which may not be recovered later. But the alternative to using these applications is a non-working flash drive and a lack of information.

Diagnosis of the problem

The main signs that a flash drive requires repair are:

  • Issuing messages about USB media copy protection or about an unidentified device;
  • The drive cannot be detected by any computer;
  • Lack of disk list;
  • Inability to read (and, of course, write) information;
  • Negative results when attempting to restore or format.

Sometimes the problem may be a USB connector or a lack of drivers on a particular computer. But when problems occur on every device, most likely the problem is with the drive. And you can try to restore it.

Utilities for flash drives

You can try to restore the functionality of the USB drive using system utilities. But when the problem is serious, the best option is to restore it through a program specifically designed for repairs. Some manufacturers produce their own applications that are best suited for repairing these particular brands. Although with their help you can restore a USB drive of any brand.

Advice: Special programs are designed for repair, not restoration. It is not recommended to extract information using them.

JetFlash Online Recovery

To restore non-functioning Transcend drives, the manufacturing company has created a special utility that can be found and downloaded for free on its official website. It's called JetFlash Online Recovery and is very growing in use. There are only 2 commands here:

  • Fix the flash drive by erasing all data;
  • Recover while saving data.

You should use the second method first. And, if he doesn’t help, be the first.

Silicon Power

There is also a recovery program on the Silicon Power website in the support section, which you can get for free. It allows you to recover, first of all, flash drives of this brand and is called SP Recovery Tool Utility.

Adata

The manufacturer Adata also has a freely available program for restoring USB media on its official website. If, using USB Flash Drive Online Recovery, it was not possible to read the information, the flash drive can be repaired, having lost the data.

Kingston flash drive repair

The owner of a Kingston drive will probably like the opportunity to get back an entire flash drive after running the MediaRECOVER 4.0 Digital Image Recovery program. In some cases, the application manages to save part of the data, even if the USB drive has been formatted. Unlike most such programs, recovery can be performed not only on video, audio and photo files, but also on Word documents, e-books and spreadsheets.

Universal programs

In addition to specialized software that mainly repairs drives of its own brand, there are several applications that can restore the working condition of most devices. One of them is the D-Soft Flash Doctor program, which provides the following benefits:

  • Menu and documentation in Russian;
  • Lack of localization for individual brands;
  • Creating a flash disk image for further work not on the drive, but on its virtual copy.

The following programs, not so well known, but also free and quite effective, are:

  • ChipEasy, which can not only easily restore a flash drive, but also recognize the manufacturer if its name is not written on the case or has been erased over time;
  • Flash Drive Information Extractor is a utility that can provide the maximum amount of data about a flash drive along with its recovery;
  • CheckUDisk – for all its ease of use, it is a very fast working and detailed information application.

How to find a program to repair a flash drive

It is possible that, even after trying all of the above methods, it was not possible to restore the functionality of your USB flash drive. In this case, you should do the following:

  1. Download the Chip Genius utility;
  2. Use it to find out the VID and PID, as well as the name of the chipset located inside the flash drive;
  3. Go to the iFlash website and enter the 2 numbers received;
  4. Find your drive model in the list.

Now all that remains is to find the corresponding program in the Chip Model column, paying attention to the match of controllers. You can find and download it for free on the Internet. The principle of operation for all of them is approximately the same - more emphasis on restoring performance, less on saving data.

Thematic video:

Sooner or later, most users encounter a situation where the flash drive is displayed incorrectly (here you can try formatting first) or the information on it suddenly disappears. But do not despair - it is likely that you yourself will be able to revive the device and successfully restore the photos and documents stored on it or “bring to life” the file system.

Thanks to our recommendations, you can save not only on the services of a specialist, but also on special programs - we will consider exclusively free software for repairing flash drives. However, it is also worth keeping in mind that different utilities are designed for devices from different manufacturers.

If you don't know the model of your USB drive

do the following:

Go to the Start menu and in the “Run” line write mmc devmgmt.msc, then press Enter. In the Universal Serial Bus Controllers section, find your “USB Mass Storage Device”, select it and right-click. Open Properties, then go to the Details tab and in the dropdown select Device Instance Code (or Hardware Codes). Write down or remember the PID and VID.

Then go to the FlashBoot.ru website and enter the VID and PID data in the special field. After this, you will receive information about your device and the utilities that are best suited to repair it.

Recovering a Transcend flash drive

To restore devices of this brand, the official Transcend RecoveRx utility is best suited. With its help, you can conduct an in-depth search for already deleted files, which you can later also recover: photos, documents, audio and video files.

By the way, RecoveRx supports all types of storage devices, including memory cards, MP3 players and external hard drives. This program works extremely simply - you just need to specify the type of files or select all.

The second method is online recovery of flash drives from the JetFlash Transcend series. To use it, you must download JetFlash Online Recovery (you must have an active Internet connection). Once launched, the tool will automatically restore all your data.

Silicon Power flash drive recovery

If you have a Silicon Power flash drive, you are in luck - the manufacturer cooperates with Recuva. The File Recovery tool provides a clear interface that will allow you to quickly scan your device and mark those that are subject to reincarnation. You can read more about the operating features of this program.

Kingston flash drive recovery

If you have lost files on media from this company, a flash drive recovery utility can also help you. If you have problems with the operation of the device, then most likely you will have to format it, and do this not with a Windows tool, but with the official Kingston Format Utility. Just launch it, select your device and click “Format”.

Recovering a SanDisk flash drive

USB drives from SanDisk have a five-year warranty, so if you suddenly encounter problems, feel free to go to the store or contact the manufacturer (e-mail.

It is quite difficult to imagine a modern person without a digital storage device. A flash drive is currently a successful portable object on which a lot of useful information is stored.

The advantage of a flash drive is that it does not take up much space and is accompanied by increased practicality. Even when dropped, it is not always damaged, as was previously the case with disks.

Another advantage is that recording the desired content on it is not only faster, but also much easier.

Unfortunately, despite its unique practicality, it may happen that the flash drive stops functioning at some certain point.

Of course, you can peacefully “say goodbye” to the dead flash drive and go to the store where you can purchase a new digital drive.

If it’s difficult for you to get rid of your usual storage media so easily, then we recommend that you study the recommendations on how to restore a “dead” Transcend flash drive.

Recovery process

Before making minor repairs to a damaged Transcend flash drive, it is important to determine the reason why it failed.

This diagnosis can be compared to the treatment of the patient. The doctor also initially examines the patient, establishes a diagnosis, identifies the cause of the pathology, and only after that prescribes treatment.

We also recommend that you “treat” your affected digital media. The Transcend flash drive recovery program will help with this quite effectively, which can be easily downloaded using offers on the network.

However, it is still initially useful to establish the cause of the failure, due to which you have to “draw” advisory information.

Reasons for failure

In most cases, you have to consider restoring a Transcend flash drive due to a banal software failure that users have to deal with quite often.

To confirm that, indeed, a software glitch presented such an unpleasant surprise, some tricks allow you to do so.

Insert your drive into the USB connector and watch what happens next. If all your attempts to open the media are in vain, but the computer still sees the Transend flash drive, then it is likely that it has suffered a software failure.

You can suspect the same if, when you connect the media via a USB connector, you hear a characteristic sound signal, but no visible changes appear on the screen, including you will not detect your media when you launch the “Computer” window.

Also, a software failure is indicated by the factor when the PC sees the flash drive, but not all of it, but only part of its disk space.

Of course, if you find confirming “symptoms” of a software failure that requires recovery of the Transend flash drive, you don’t need to fall into despair and feverishly remember what could have caused such trouble.

You, of course, could have caused the digital storage device to fail if you neglected the recommendations on how to properly remove the drive from the USB connector.

The reason for the failure may be a fall of the device or strong mechanical compression. There may also be reasons that are completely independent of the user’s actions.

Troubleshooting

Those who are convinced that the drive has stopped responding to any actions want to find a program for flash drive recovery.

Indeed, a utility for restoring a Transcend flash drive exists; it is not so difficult to find, download and install on a computer.

One of the programs for flash drive recovery

However, it is initially important to make sure that the digital drive is still “dead”. Sometimes it happens that it does not respond on one PC, but functions perfectly on another computer.

Often a software failure is detected on the PC itself, when, for example, the drivers have crashed.

You can also try disconnecting all peripheral devices from the USB connectors and connecting only the flash drive. Even such a simple move can sometimes easily fix the problem.

If all attempts are in vain, we recommend that you inspect your digital drive from all sides. It is useful to pay attention to all chips and cracks that you find on the body.

It wouldn’t hurt to look inside the part that connects to the USB connector. Sometimes such a visual inspection is enough to identify poor internal contact.

Don’t be afraid to carefully open the media case and inspect it for integrity inside. It is useful to carry out a thorough visual inspection of its internal contents.

You can also try to fix a bad contact yourself, but only if you have special tools for this. If there are none, you are unlikely to be able to eliminate even the identified problems.

Only after you are convinced that mechanical damage is excluded, you can move on to the next stage, after which the digital media can be restored.

Of course, in this case you will definitely need a Transend flash drive recovery program.

To correctly restore a flash drive, it is important to first clarify the type of memory installed on the media, its ID, firmware version, controller ID and other technical details.

In this case, you will not be able to do without the help of the special Chip Genius utility. With such a utility, you will not only receive information quickly, but it will be accurately presented without errors.

Based on the information received, you can begin a search, the purpose of which is a program to recover your flash drive.

The ideal solution to the problem you identified is not even a recovery utility, but the JetFlash Online Recovery service program.

This option is suitable for those users whose computer is provided with constant and reliable access to the Internet.

Don’t even get yourself ready for a labor-intensive process; your expectations will be in vain. Immediately after launching such a service program, as well as connecting the digital “dead” drive to the USB connector, the “reanimation” process will start automatically.

You just have to wait patiently for the process to complete. The only thing you have to do is click on the “Yes” button, confirming your willingness to grant the rights to work with the flash drive to the program itself.

Once the work is completed, the program will notify you about this. Now unplug the flash drive and then plug it back in. If the resuscitation process was effective, you will instantly find that your digital drive has come to life. You can again perform copying, recording and other functional user manipulations on it.

If the flash drive still doesn’t come to life, you’ll have to say goodbye to it and buy yourself a new digital “assistant.”

So, you were able to see that the process of recovering digital media is not complicated. However, such a process requires increased attention and responsibility for every step taken.