Menu
homeMicrosoft

Turning on and off. Apple watch gps calibration. Turning on and off How to reset Apple Watch to factory settings

Starting from the second generation, the Apple Watch has received an increased battery, which significantly extends the operating time of the gadget. However, this is not enough for some users and they want to further extend the battery life of the watch.

It is logical to assume that to do this you need to disable such power-intensive functions as GPS navigation. But how to disable GPS in the watch settings and is it possible to do this at all?

Can I turn off GPS on Apple Watch Series 2 and 3?

In short, no, there is no option to turn off GPS in the Apple Watch settings. The fact is that The watch itself turns this function on and off depending on the situation.

Of course, Apple understands how demanding the GPS chip can be in terms of power consumption, so the watch uses it only in certain cases.

For example, if the user has an iPhone with geolocation enabled, the watch will receive location and movement data from it, thereby saving charge. Many users mistakenly think that if you turn off geolocation on your iPhone, it will also turn off on your watch, but in fact, this has the exact opposite effect.

In addition, when training mode is enabled, GPS will only be used when moving in open areas. Thus, when jogging, as well as swimming in the sea or lake, location detection will be turned on, but in the case of training in the gym or pool, it will be turned off.

In other words, the Apple Watch simply remembers the GPS data it received from the iPhone during the last sync session. Naturally, you start a workout, for example, for running, leaving your smartphone at home or in the car, and after completing the workout, when you are near your smartphone again, Apple Watch will automatically sync with your iPhone, and all the data from the last workout, including your route, will be available in the “Activity” application (in the “Training” tab).

If GPS is required for third-party applications, it will be activated only for the duration of the actual location determination work.

If you notice that the GPS on your Apple Watch is not working correctly (does not accurately track your location or calculate distances), then you need to calibrate your smart watch.

At the same time, Apple does not position the Apple Watch as a watch with improved battery life. This is due not only to the brighter display, but also to the fact that the operating time directly depends on the user’s lifestyle. After all, people who often run in open areas or swim in open bodies of water may not notice a significant difference.

The most personal Apple device ever and the newest addition to the Apple product ecosystem will be available on April 24th. The company positions Apple Watch as an ultra-precise watch, a personal device for instant communication, and a fundamentally new assistant for health and fitness.

The Apple Watch, although it looks like a watch, is actually a multifunctional mini-computer. The device can serve as a music player like an iPod, a fitness tracker and heart rate monitor, a communications device that allows you to accept/reject calls and respond to SMS. The watch can also act as an iPhone viewfinder, wallet replacement, and home electronics remote control.

Due to the completely new form factor, traditional methods of controlling the device are not suitable. For this reason, Apple has developed a number of fundamentally new techniques. Read more about how to interact with Apple Watch later in our article.

1. Scrolling and zooming

Apple Watch features special technologies including the Digital Crown, which provides easy scrolling, zooming, smooth navigation, and helps you avoid blocking the display with your hand. Apple calls the wheel the most revolutionary way to navigate since the Click Wheel on the iPod and multi-touch technology on the iPhone.

2. Return to the main screen

To return to the home screen, just single-click on the Digital Crown. It behaves almost like the Home button.

3. Siri

4. Switch apps

Double-clicking the Digital Crown switches between the watch face and the latest app. A simplified analogue of the multitasking panel on the iPhone.

5. Universal access

Triple-clicking the Digital Crown opens the section for managing universal access. Apple's smartwatches, like the iPhone and iPad, have a number of settings for people with disabilities.

6. Friends

Click the button on the side to open the “Friends” section: avatars of people with whom you always need to stay in touch will appear here. Tap to send a message, make a call, send a drawing, or send your heartbeat.

7. Turn on and off

To turn off Apple Watch, press and hold the button on the side. After a few seconds, buttons to force close apps and turn off your Apple Watch will appear. To turn on the watch, just press the side button once.

8. Apple Pay

Double-click the button on the side to bring up Apple Pay. After authorization on iPhone 5 or iPhone 6, the payment service will work as long as the watch remains on your hand.

9. Screenshots

To take a screenshot from the Apple Watch screen, you need to press the Digital Crown and the side button at the same time.

10.Force touch

The Retina display with Force Touch on Apple Watch recognizes the difference between a touch and a press, offering a new way to quickly navigate to relevant controls. Force touch works similar to right-clicking a mouse, which brings up a context menu on traditional computers.

As of 2017, Apple Watch Series 2 is the most popular smart watch in the world. They are also one of the most functional, as well as the most expressive in design. Developers are willing to write applications for them, so the watch can not only show the time and notify you of messages, but also help in business, sports, shopping, and also save money.

There are now two generations of Apple Watch smartwatches on sale (Series 1 and Series 2), which are not so different from each other. Innovations in the second generation include a more powerful processor, enhanced water protection and finally GPS on board. Special editions in collaboration with Hermes and Nike are also available. The operating system update also added speed, as well as new watch faces and interface improvements.

We offer an overview of useful Apple Watch features and capabilities that are worth knowing:

  1. You can answer calls directly from your watch. When there is an incoming call, the answer and end buttons are displayed.
  2. Replaceable dials. The standard set has dials for every taste (including analog and digital). Plus you can install additional ones.
  3. View SMS and iMessage and quickly respond to them. Smartwatches offer an excellent set of standard quick responses.
  4. Correspondence on Facebook Messenger. Gradually, all popular instant messengers are learning to work with watches.
  5. Checking email (both through the standard application and through third-party ones).
  6. Quickly send emoticons directly from the device screen.
  7. Switch to silent mode, for example, in a meeting or in a movie.
  8. Quickly access application information on your iPhone or iPad (if the application supports this feature).
  9. Notifications about incoming messages on iPhone, from system or third-party applications.
  10. Built-in heart rate monitor.
  11. Sending heart rate monitor readings to another device (for example, a doctor or trainer).
  12. Payment via Apple Pay using NFC-enabled terminals.
  13. Record your walking and jogging route.
  14. Launching applications on iPhone.
  15. Voice requests to Siri.
  16. Viewing photos (yes, even though the screen is small, the photos look quite impressive on it).
  17. Sending drawings (Digital Touch). You can draw directly on the watch screen.
  18. Send location. It's faster than explaining over the phone where you are for a long time.
  19. Get directions in the Maps app.
  20. Offline music playback from iTunes. Your music library is stored directly in the watch's memory.
  21. Search for a smartphone. The Find My iPhone app will make your phone beep loudly.
  22. Remote camera control. Forget about selfie sticks: the watch makes pressing the shutter more convenient, and the smartphone can be placed in any convenient place.
  23. Control of Apple home appliances (TV, Time Capsule, etc.).
  24. Connection to the car. Modern automotive electronics systems are interfaced with mobile technology.
  25. Sports tracking.
  26. Storage of electronic tickets. Conductor scanners perfectly read QR codes from the watch display.
  27. Sending an SOS signal in an emergency.
  28. Night clock mode. Dock your Apple Watch and you'll be able to see its watch face from afar.
  29. Working in water. You can swim with an Apple Watch, but without fanaticism. The model is waterproof up to 50 meters (5 ATM).
  30. You can move the hands forward 10 minutes to have some extra time when planning meetings and trips. Self-deception? Yes.)

Which of these functions is more useful for you - experience will show (we bet on notifications, payments and remote control of the player and camera). However, there is no doubt that Apple and third-party developers will still be able to open up a lot of new applications for smartwatches.

Apple Watch Series 3 is the latest generation of smartwatches from the Cupertino tech giant. Unlike Series 2, they are equipped with a stand-alone LTE module that works through the built-in eSIM (not yet supported in Russia), thanks to which they can be used even without a smartphone. But it will still be required to activate the device.

How to turn on Apple Watch Series 2, 3?

To turn it on, press and hold the “long” (not round!) side button until the manufacturer’s logo appears on the display.

If after 10-15 seconds of holding the long side button the screen does not flash and the device does not turn on, make sure that it is sufficiently charged. Connect the “charger” and leave it for 30 minutes. After that, you can try to turn on the device again.

How to set up Apple Watch Series 2, 3?

For the initial setup, you will also need a smartphone updated to the latest version of iOS, with Bluetooth turned on and an active Internet connection (via a mobile network or Wi-Fi).

How to do initial setup

In order to initially set up your smartwatch, you will need an iPhone with Internet access. How to connect these two devices:

  • Turn them on;
  • Bring your watch to your iPhone. Wait a while until a message appears on the phone screen prompting you to use your smartphone to make settings. Click “Next” there. If it doesn't appear, check Bluetooth - it should be turned on. You can also open the corresponding application and click the “Create a pair” button;
  • After this, a special animation will appear on the watch screen, and the smartphone will turn on the camera through which it will recognize it. Place the companion device's display in the center of the viewfinder as shown in the tips. If automatic recognition does not occur, click the “Create a pair manually” button. The wizard will demonstrate instructions for pairing devices;
  • Choose which hand you plan to wear the watch on;
  • Agree to all terms of use;
  • Enter your Apple ID password.

How to connect Apple Watch 2, 3 to WiFi?

When initially activated, the smartwatch copies the settings profile from the connected smartphone. That is, if Wi-Fi, GPS, Siri, etc. are enabled on the iPhone, they are automatically activated on the companion device. Wireless network passwords will also be transferred along with the rest of your data.

You can enable WiFi on Apple Watch 3, as well as disable it or configure other settings directly in the corresponding window of the initial setup wizard.

What else can you do?

In the Initial Setup Wizard you can also:

  • Set a login password. It will be activated when this accessory is removed from the hand;
  • Set up a branded payment service;
  • Install applications from the AppStore.

During the initial setup process, various usage tips will be shown on the smartphone screen.

Key features of Apple Watch Series 2, 3

Activity analysis of Apple Watch Series 2, 3

The program for tracking physical indicators is called “Activity” and is pre-installed watchOS software, that is, it is ready to work immediately after the initial setup.

Interesting

Instructions on how to enable or disable activity tracking are shown directly in the initial setup wizard on your smartphone. There are also hints in the application itself.

The donut chart interface displays the following metrics:

  • The number of calories burned during movement (the “Mobility” parameter);
  • Total duration of movements (parameter “Exercises”);
  • The number of hours in the current day in each of which you moved for at least 1 minute (the “Warm-up” parameter).

To view detailed information about each parameter, you need to swipe up on the screen with pie charts.

The “Exercise” and “Warm-up” parameters are not configurable. “Mobility” can be changed with a strong tap on any screen - after this, a screen will open with settings for the number of calories that need to be burned to achieve the daily goal.

Reminders about the need to “walk” are configured in the control application on the smartphone, in the “My Watch” - “Activity” tab.

How to measure blood pressure on Apple Watch Series 2, 3?

No way. This model, like the previous ones, is not equipped with a built-in blood pressure monitor and therefore cannot measure blood pressure.

Heart rate measurement on Apple Watch 2, 3

To measure your pulse, you need to launch the “Pulse” program from the application menu. In addition, the device constantly analyzes heart rate when the “Training” mode is active, as well as 3 minutes after its completion.

When you first open the Pulse program, the application will offer to enable notifications about increased heart rate in the absence of physical activity. If necessary, this function can be activated.

Apple Watch Heart Rate Variability

To measure heart rate, photoplethysmography technology is used, i.e. The pulse is analyzed by the degree of light transmission of blood in the vessels under the skin.

As a result, the quality of heart rate measurement may vary depending on how the photocells adhere to the skin, skin color, the user's health status, and other factors. The exact value may differ by several beats per minute from the measured one, either up or down.

Sleep analysis in Apple Watch Series 2, 3

There are no built-in tools for monitoring the quality and phases of sleep in this companion device. Therefore, for tracking, it is recommended to use third-party software that can be downloaded from the AppStore - such as Sleep++, AutoSleep, Sleep Better, Sleep Tracker, etc.

How to track sleep on Apple Watch 2, 3 using third-party software

The operating principle of various third-party software is approximately the same. Required:

  1. Install the desired sleep tracker from the AppStore;
  2. Open the sleep tracker and start tracking mode.

Smart alarm clock for Apple Watch Series 2, 3

To use the watch as a smart alarm clock, you will also need to install third-party software that supports this function. For example, Sleep++ or similar from the above list.

How to use Apple Pay on Apple Watch 2, 3?

In order for the proprietary payment service to work, you will need to set a password code. This is described in the instructions for initial device setup. In addition, right in the same menu you can link the card with which you plan to pay for purchases.

To configure the service, if this item was skipped in the initial setup menu, you will need:

  1. Open the Watch application on your smartphone;
  2. Open the “My Watch” tab;
  3. Open the “Wallet and Apple Pay” item;
  4. If you don't have a passcode set on your watch, the app will prompt you to set it right now. Do it;
  5. Click "Add card";
  6. Select a card from among those already linked - or enter the details of a new one;
  7. Enter the card security code;
  8. Click “Next” and wait for information from the issuing bank;
  9. Click Next.

That's it, the branded payment service will work.

To pay in a store, you will need to quickly press the side button on the watch twice and then bring it face down to the terminal. When activated they will vibrate slightly.

Need to know

If the transaction size exceeds 1000 rubles, you will have to enter the PIN code of the linked card at the terminal to pay.

Unlock Mac with Apple Watch

The watch can only unlock Mac computers and laptops that run macOS High Sierra and support wireless Bluetooth connectivity. In addition, all company devices must be associated with one account. To set up unlocking you need to do the following:

  1. On a computer or laptop, open the “Settings” application, select “Protection and Security”, then “General”;
  2. Check the box next to “Unlock Mac with Watch”;
  3. Enter your account password;
  4. Confirm.

All. Now the computer will unlock automatically.

How to charge Apple Watch Series 2, 3?

To charge, you must use the included wireless charger. It is enough to connect it to the network and place the back of the watch on its active surface. The charger is equipped with special magnets that automatically align it.

You can also use AirPower wireless charging.

How to Charge Apple Watch Outside the Home

You can use more than just a household network for charging. The power cable can also be connected to the USB ports of a computer, laptop, external battery (“power bank”) or any similar charger.

How to update Apple Watch 2, 3?

Software updates (watchOS) are performed via a linked iPhone smartphone. Instructions:

  1. Set the watch to charge. You cannot remove the charger until the update is complete;
  2. Make sure they are more than 50% charged;
  3. Open the Watch application on your smartphone, in it - the “My Watch” tab;
  4. Select “Basic”, in it – “Software Update”;
  5. Download the update. If necessary, you will need to enter a password for your account;
  6. The update will be installed automatically;
  7. The update may take time to install. Wait for it to finish. The corresponding indicator will report this.

You can remove the watch from charging only after the update is complete.

Can I connect Apple Watch to Android?

No you can not. Apple Watch does not work with Android phones. There is no third party app that emulates the corresponding iOS software.

However, the user community is looking for another way to connect these two devices. But for now, the answer to the question “Does Apple Watch work with Android” is no, it doesn’t.

Express guide to Apple Watch Series 2, 3

How to check Apple Watch 2, 3 for authenticity

First, make sure it's a Watch and not an iWatch or something like that.

How to check Apple Watch upon purchase:

  1. Carry out a visual inspection. Make sure that the case is free of any connectors, including slots for SIM cards or memory cards, charging connectors, etc.;
  2. Turn on your device. Make sure it actually turns on;
  3. Try connecting to your smartphone. If during the initial setup the device prompted you to enter your account information, you can enter it. The main thing is that there is no “Activate Watch” screen.

How to turn off GPS on Apple Watch 3

GPS does not turn off. You can turn it off on your phone, then the number of geolocation requests will decrease slightly.

Apple Watch Series 2, 3 is not charging - what to do?

If your Apple Watch won't charge, you can try the following:

  1. Make sure the power supply is plugged into an outlet and that there is current. Try a different outlet;
  2. Make sure the wireless charger is in contact with the watch and the magnets are aligned. Try reconnecting. Try turning the charger over;
  3. Make sure that the chargers (including the wireless module, cable and power supply) are original and included in the package;
  4. The charger must not have any shipping film on either side;
  5. The charger and watch must be clean;
  6. Try to force restart your watch. Press and hold the round and side buttons for 10 seconds. After rebooting, put it on charge again;
  7. Try a different cable, a different power supply, a different wireless charger.

If they still do not charge, take them to a service center.

How to reset Apple Watch to factory settings

The easiest way to reset is to remotely delete all personal data via iCloud:

  1. On your computer, open icloud.com;
  2. Log in to your account;
  3. Select “Find iPhone”;
  4. Select your watch from the available devices;
  5. Click "Erase" and then select "Next" until the process is completed;
  6. Also click the “Delete” button (icon with a cross) next to the name of the watch.

Through the application it is a little more difficult. More details about this will be written later in this manual in Russian (in the section “How to break up a couple”).

In order to reset the watch (to perform the so-called “Apple Watch Restore”), the iPhone associated with it must be connected to the Internet via mobile or Wi-Fi.

How to charge Apple Watch without original charger

The third generation companion device (Apple Watch series 3) has limited support for the Qi wireless charging standard, so may be compatible with some chargers. Try placing the back of it against a Qi-enabled active charger for a few seconds. If charging works, this device can be used.

How to unpair Apple Watch 2, 3

Before you can sell your watch, you will need to remove your own credentials from it. How to unlink Apple Watch from Apple ID:

  1. Open the control application on your phone;
  2. Open the “My Watch” tab;
  3. Open the “Information” menu (indicated by the i symbol in the circle next to the name of the watch);
  4. Select “Break pair”;
  5. If you are using a tariff plan, click “Delete tariff”;
  6. Enter your account password;
  7. Confirm your desire to break up the couple.

Unlinking also resets to factory settings.

Notifications do not arrive on Apple Watch Series 2, 3

This may be due to the following:

  • The smartphone to which the smartwatch is connected is currently in use. Then notifications are displayed on it;
  • The watch has a screen lock or Do Not Disturb mode active. Unlock or disable this mode through Control Center;
  • The watch is disconnected from the phone. This is indicated in the Control Center with a special icon. Turn on Wi-Fi and Bluetooth on your phone, and on your watch, first activate Airplane mode and then turn it off.

How to unlock Apple Watch 2, 3

To unlock your watch, tap the screen or briefly press any button, and then enter the passcode you set earlier.

How to change the strap on Apple Watch 2, 3

The watches use special straps with a proprietary fastening. It will not work to use a standard spring one, common in analog devices. But to change the strap, it is enough to remove the old one and install a new one in its place until a characteristic click appears.

How to remove the strap from Apple Watch

  1. Turn the clock face down;
  2. Press the strap release button (located next to the strap);
  3. While holding the release button, slide the strap to the side.

How to turn off Apple Watch

To turn off your watch, press and hold the side button until the “Off” slider appears, then slide it.

At a recent conference in San Francisco on September 7, 2016, Apple presented not only the new iPhone and AirPods headphones. Among other things, another model popular among athletes “smart watch” Apple Watch Series 2 with GPS module. The latter have not been updated for two years.

If you want to buy iWatch 2, we advise you to follow the link provided, where you can find a huge selection of stores and models of smart watches.

Why do you need GPS in a watch?

While unique characteristics have long been known about the new iPhone 7, almost nothing clear and accurate has been reported about the iWatch device. But it is already clear that the new model has the following features:

  1. High-quality waterproof function, the gadget will even withstand immersion under water.
  2. The screen brightness is much higher (a setup guide is available at the link provided).
  3. A more modernized chipset is used, which has increased the speed by half and improved the graphics.
  4. Built-in GPS module in Apple Watch Series 2.

The latter is worth dwelling on in more detail.

Does Apple Watch have GPS?

Why does iWatch need a GPS module?

The second series of smartwatches is likely to become a popular device among athletes. Since this unique mode for smartwatches is turned on only when training in the fresh air. For example, when walking or running, such a gadget will help you track your performance without using an iPhone. A person goes in for sports, and the watch builds a track. The display will not only indicate the distance and speed of movement, but also the athlete’s pulse.

A small nuance

However, when you turn on the Apple Watch Series 2 for the first time, the GPS module of which has not been activated before, it may turn out that the device does not work entirely correctly. When starting a training regimen, it is not always possible to build the right path first. The first time the path lines are most often:

  • performed roughly;
  • with large discrepancies with the map.

There are two reasons for this:

  • lack of calibration;
  • inaccuracies of built-in maps (for example, Yandex.Navigator and Yandex.Maps).


The second problem cannot be fixed, but the first problem is completely solvable. The Apple Watch 2 GPS will need to be calibrated. To do this you need to:

  • go to the developer’s website;
  • follow the instructions provided.

After the operation, the track is built with maximum accuracy, even if there is:

  • difficult path;
  • visiting shops or other buildings.


Autonomy of work with disabled GPS

The manufacturer indicates an operating time of 18 hours. But everyone understands that the indicator is relative. The duration of operation without recharging depends entirely on the intensity of use. If you turn off GPS in the Apple Watch Series 2 (more precisely, do not use functions where the module is needed), the device will last longer without recharging.
Accordingly, the less actively you use the new features of the gadget, the longer the device works offline.

Apple Watch Series 2 module

How to disable the GPS module

You should press the bottom edge of the clock display and hold for a while. After this action, the Clock Control Center will open. Next, you need to swipe up and click on the lit GPS icon. When the symbol darkens, the module will turn off.

GPS module does not turn on on Apple Watch Series 2

If you have problems turning on the navigation module, you should try restarting the device. If the module does not work after this, it is recommended to clean the device via a smartphone. As a last resort, remove and install the program again.

Instead of a conclusion

In conclusion, I would like to note that almost all innovations in iWatch watches are related to fitness capabilities. Most likely, people who are not closely involved with sports should not rush to exchange the old version of their smartwatch for a newly released gadget. But athletes will appreciate the inclusion of a GPS module in the device. Probably only they don’t have a question, why GPS in Apple Watch 2, since a new option has been added for them.