Menu
homeBrowsers

How to set up an asus rt n12 modem. Checking the Internet connection status. Checking the wireless part of the LAN

After purchasing an asus rt n12, you have a question: how to set up a local wifi network. To answer, you need to understand the features of connecting through this router. This is exactly what we will do now.

So, first of all, let's look at the connectors on the back panel of the equipment and connect the cables correctly. There are 5 special ports on the back of the router: 1 of them is for WAN, to which the main provider cable is connected, and the remaining 4 are for LAN type cables.

After connecting all the cables, it is best to perform further configuration from a personal computer that has a direct connection to the equipment. Next, we move on to setting up the router itself.

IMPORTANT! To connect a desktop computer or laptop, a LAN cable is used, one end of which is connected to any LAN port on the router, and the other to the corresponding port on the network card of your personal computer or laptop.

This recommendation may seem funny and obvious to some, but still check the connection of the router to the outlet. And also make sure that the Internet connection is working and there are no problems with the provider. In addition, check that only the local network connection is active.

Initial router setup

We have already connected all the cables, checked the Internet connection and plugged the router into a power outlet. Now we need to learn how to configure the route. And this is done as follows:


IMPORTANT! We write “admin” if we have not yet changed the factory settings.

  1. If you are setting up equipment for the first time and have logged in for the first time, automatic setup will start. With automatic setup, you only need to click on the “next” button and enter the required data.
  2. Then the router will determine the type of Internet connection. If it is successfully determined, enter the password and username that you usually use to access the Internet.
  3. Now you need to enter a personal name for the Wi-Fi wireless network and come up with a password for it.

If you cannot configure the equipment and establish correct operation using automatic settings, and the connection type was not detected automatically, you must make the settings manually.

Setting up a local network of various providers using a router

Internet settings from Beeline, Rostelecom and Dom.ru differ from each other. Next, we will consider the setup procedure for each provider.

First, let’s look at setting up the Asus RT-N12 for the Beeline network: on the main router settings page (we accessed it through the browser address bar using the router’s IP address), click the “Internet” section. A window opens in front of us, where we fill in some lines, as shown in the illustration below. The main thing is to select L2TP in the connection type and tp.internet.beeline.ru in the VPN server item. We put ticks in two places, as in the figure.

After that, save the entered data by clicking “Ok”. If all items are checked correctly, after 20-30 seconds the connection to the Beeline network will be disconnected. Then, after a few seconds, the connection will be restored, and you will be able to work with various sites and other Internet resources. Also, the Wi-Fi network will be correctly displayed and work on all devices: smartphones, tablets, and so on.

If you use the services of Rostelecom or Dom.ru, then we configure the router in the same way, but only on the main page of the router settings in the “Internet” section we indicate other data: in the connection type item we indicate PPPoE, and not L2TP, as before. We also enter your unique username and password. The remaining points remain unchanged. The illustration below shows what a completed section looks like.

Setting up a wireless Wi-Fi network using the Asus RT-N12 router

Open the menu and select “Wireless Network”. Next, fill in a number of points:

  • The first item is the SSID, or the name of the wireless network. The name of your network will appear in the Wi-Fi search list on all devices within range of the network. The name is written in English letters.
  • In the “Authentication” section, select WPA2-Personal.
  • Next, enter the password in the “WPA Pre-Shared Key” section. The password must consist of at least 8 digits.
  • Save the settings.

The figure below shows what the “Wireless Network” section looks like.

Setting up a local network via asus rt n12

So, we figured out how to connect and configure the asus rt n12 router. Now let's look at how to set up a local wifi network via asus rt n12.

Go to the “Local Network” section.

We change the router address, which was set by default, do this in the “LAN IP address” tab.

Enter the IP address of your local network and click “Apply”. After this, the equipment will work for your local network.

ASUS has long earned worldwide recognition as a manufacturer of high-quality computer equipment. One of the areas of activity of the enterprise is the production of network devices. The ASUS RT N12 VP router model ranks first in popularity among routers of this brand. How to configure this device correctly? This review will help you find out everything!

The router can be configured for any provider

Very often, users install an ASUS router somewhere in a corner of the apartment, and only then think about how to properly configure the equipment to work via Wi-Fi. Experts recommend setting up by directly connecting to a PC, and only then transferring it somewhere. The connection process is no different from connecting other routers to a PC:

  • provide ASUS RT-N12 VP with power (plug into a power outlet);
  • insert the provider cable into a port that is different in color from the others;
  • connect the computer and your router with a wire (included with the device) (insert one end into the network card, the other into any of the ports of the N12 VP router).

Now everything is ready for further configuration of the router.

Reset

To set up your router, it is important to initially perform a factory reset. Use a match or a toothpick - it will allow you to get to the reset button (a small key located deep in the device). Press the button for ten seconds. All indicators on the ASUS RT N12 VP panel should light up. After this, the router should reboot on its own.

Login to the interface

Configuration is carried out in the web interface. It’s easy to get into it - write the line 192.168.1.1 in the address bar of any browser you like. After such manipulations, you will see a window with fields for name and password. You need to enter the standard data for any router (admin/admin). Confirm your decision by pressing Enter.

Internet settings

An overview of the window that appears will help you understand the basic settings. It is advisable to perform all manipulations in order, so we will immediately discard the quick settings mode. Go to the home (main) page of the router menu. Depending on the specific firmware, you may need to press the "Next" button.

To be able to use the Internet, you must correctly configure the ASUS RT N12 VP connection. To do this, specify the connection type and also enter the information provided by the provider. The most useful data is indicated in the contract issued by the operating company. If you lose such a document, contact technical support - they will help you.

The router settings look like this:

  • on WAN - YES;
  • type - WAN connection;
  • on UPnP - YES;
  • IP - automatic (or dynamic);
  • on NAT - YES.

UPnP is needed for the normal functioning of the file hosting service via the ASUS RT N12 VP router. Some providers bind users' computers to a specific MAC address. If such information is in the contract, it must also be entered in the field provided for this. Don't forget to fill in your Username/Password in your account settings. The decision to save the changed information is confirmed by pressing the “Accept” button, after which the Internet setup is considered complete.

The steps may vary (it all depends on the specific provider), but the general principle remains the same. The only difference is the type of connection used (for Beeline - L2TP).

Wi-Fi setup

Making ASUS RT N12 VP a router, with the help of which the Internet will be distributed to other devices, is also not difficult. So, Wi-Fi on the n12vp router is configured in the “Wireless Network” section. Enter the following parameters in the “General” section:

  • SSID - network name (you need to enter any name that will help distinguish your network from your neighbor’s);
  • WPA key - create a strong password for your Wi-Fi;
  • authentication method - WPA2-Personal;
  • save changes.

In this article we will talk about setting up the ASUS RT -N 12 router.

Step 1. Connecting the router to the PC

Everything is as usual - we insert a patch cord into any of the yellow ones (usually it comes included), at the other end we connect it to the corresponding PC connector or from which the settings will be made.

Insert the Internet connection cable into the blue WAN port.

Turn the router over and look at the default settings. We will need to know: connection IP address, username and password.

On the computer, in the network connection properties, select automatic acquisition of an IP address.

Then go to any convenient browser and in the address bar write the same IP address that is written on the sticker at the bottom of the router.

To configure the router, go to the “Advanced Setting" menu.

The menu items are exactly the same for the left and center windows, so here you should base your personal preferences on convenience.

Step 3: Set up a wireless network

Go to the “Wireless” submenu, General tab.

In the “SSID" field we write down the name of the wireless network; there is no need to hide it - put a checkmark in the "No" position for the "Hide SSID" field.

Since there are still quite a lot of devices that do not support the n-standard, in the “Wireless Mode” field we set the mode to “Auto”.

The channel bandwidth (Chanel bandwidth) is usually 20 MHz, but you can experiment by setting the width to 40 MHz.

Select the automatic mode of the broadcast channel, “Chanel” – “Auto”.

Authentication method - WPA2-Personal, encryption type AES. In the “WPA Pre-Shared Key” field, enter the password to access the wireless network.

Apply the entered “Apply” settings.

Go to the “WPS” submenu and disable the corresponding mode by pressing the “Disable” button.

Step 4. Configuring internal (LAN) and external (WAN) networks

Let's start setting up the internal network. Go to the “LAN” menu. Here, if necessary, you can change the IP address of the router.

Go to the “DHCP Server” tab.

By default, the router's DHCP server is enabled - for the “Enable the DHCP Server?” field. is set to “Yes”.

The pool of addresses issued to clients can be reduced to two dozen in the “IP Pool Ending Address” field; at the end, change “254” to “20”.

Interesting! The time for assigning an IP address to a client is 24 hours or 86400s (“Lease Time”).

Apply the “Apply” settings.


Let’s go to the “WAN” menu and look at connecting via the PPPoE protocol. In the “WAN Connection Type” field, select PPPoE.

As a rule, connecting via PPPoE involves automatically obtaining an IP address, so in the “WAN IP Setting” section, in the “Get the WAN IP automatically” field, mark “Yes”.

The same thing, to get a list of DNS servers of the provider “Connect to DNS Server automatically”, check “Yes”.

In the Account Setting section, in the “User Name” and “Password” fields, enter the user name and password that are specified in the agreement with the Internet provider. Click “Apply”.

Go to the “Administration” menu, “System” tab. We change the standard password “admin” to another, more complex one. Also, in the “Time Zone” field, select your time zone.

Save the settings “Apply”.

If necessary, after configuring all parameters, you can save a backup copy of all settings.

To do this, go to the “Restore/Save/Upload Setting” tab and click the “Save” button, after which we select the location where the file will be saved.

To restore, you need to click on the “Select file” button, select the settings file and click “Upload”. To reset all settings to factory settings, press the “Restore” button.

In order to get to the router’s web interface, you need to open your Internet browser and type 192. 168.1.1 in the address bar, Username - admin , Password - admin(provided that the router has factory settings and its IP has not changed).

Setting up Wi-Fi on the router

In the router interface, you need to go to the tab on the left Extra options Wireless network.

We set the parameters as follows:

  1. Field SSID: Enter the name of the wireless network. The value in this field cannot be changed.
  2. Authentication method: WPA2-Personal
  3. WPA encryption: TKIP or AES
  4. WPA Preshared Key: you must enter any set of numbers from 8 to 63. They also need to be remembered so that you can specify them when connecting to the network.
  5. Click the button below Apply

Setting up an Internet connection

In the router interface, you need to select the tab on the left Extra options, in the list that opens, select WAN.

Setting up a PPPoE connection

  1. WAN connection type: PPPoE
  2. Get a WAN IP address automatically: Yes
  3. Username: Your login according to the contract
  4. Password: Your password according to the agreement
  5. MTU: 1472
  6. Save the settings with the button Apply.

Setting up an L2TP connection

  1. WAN connection type - L2TP
  2. YES
  3. automatically- put a point on YES
  4. Username and Password- login and password from the contract
  5. VPN server -
  6. The remaining parameters can be left unchanged. In the hostname, write something in English. Save settings.

Setting up PPTP (VPN) when automatically obtaining a local IP address

  1. WAN connection type: PPTP
  2. Enable WAN, Enable NAT, Enable UPnP - set it everywhere YES
  3. Get an IP address and connect to DNS automatically- put a point on YES
  4. Username: Your login according to the contract
  5. Password: Your password according to the agreement
  6. enter the IP address or name of the VPN server according to the contract
  7. Save the settings with the button Apply.

Setting up PPTP (VPN) with a static local IP address

  1. WAN connection type: PPTP
  2. Get an IP address and connect to DNS automatically- put a point on No
  3. IP address: We enter your IP address according to the contract
  4. Subnet mask: We hammer in the mask according to the contract
  5. Main gate: We drive in the gateway according to the contract
  6. DNS server 1: And DNS server 2: enter your provider's servers (Rostelecom Omsk DNS 1: 195.162.32.5 DNS 2: 195.162.41.8)
  7. Username: Your login according to the contract
  8. Password: Your password according to the agreement
  9. Heart-Beat or PPTP/L2TP(VPN) server: enter the IP address or name of the VPN server according to the contract
  10. Save the settings with the button Apply.

NAT when automatically obtaining an IP address (DHCP)

  1. WAN connection type: Dynamic IP
  2. Save the settings with the button Apply

Checking Internet connection status

Saving / restoring router settings

After setting up, it is recommended to save them so that if problems arise, you can restore them. To do this you need to go to the tab Additional settings, menu Administration;, Restore/Save/Load settings tab.

  • To save the current router settings, you must press the button Save. The settings file will be saved to the specified location on your hard drive.
  • To restore settings settings from a file, you must click the button Choose File, specify the path to the settings file, then click the button Send.

Attention! Button press Restore will restore factory settings!

How to connect and configure a router ASUS RT-N12 on one's own? In this instruction, I will show you step by step how to install Internet on it and distribute a WiFi signal without a disk. For those who have a different model, for example N10U, N14U, N56, N18, don’t worry. This Asus manual is universal for any router with the latest version of the interface design in black and blue.

How to connect the ASUS RT-N12 VP router correctly?

First of all, let's see how to connect Asus router to computer. I will not describe this procedure for a long time here. I will just name the main steps:

  1. We take out the Internet cable from the network card of the computer and insert it into the WAN port on the Asus router
  2. Instead, we connect the Ethernet cable to the PC, which was in the box along with the router
  3. Insert the other end into the LAN connector

For those who doubt the correctness of their actions, I recommend reading. It describes in more detail the sequence of actions on how to connect the Asus RT-N12 router to a computer with a cable.

In it you will learn how to enter the control panel for configuration and at the same time avoid mistakes.

Computer settings for connecting to the ASUS RT-N12 VP router

Let's move on. Before you actually start setting Asus router, you need to make changes to the configurations of the network card of your computer or laptop. This is necessary in order to be able to access the control panel.

Namely, in the section “Network and Sharing Center - Changing adapter settings”


Here we find either an “Ethernet” connection or a “Wireless connection” - depending on how you are going to connect your PC to the router, via wifi or cable. Right-click on the desired type and go to “Properties”.

Next, open “Internet Protocol Version 4” and set all parameters to “Automatic acquisition”. If some data has already been registered here, then transfer it to paper - it will be useful for further setting up the router using the “Static IP” type.


Then we save the changes.

Setting up the ASUS RT-N12 VP router step by step

Now you can go directly to setting up the Asus RT-N12 router. We need:

  1. Login to the admin panel
  2. Change default password
  3. Select the type of Internet connection
  4. Specify parameters for the WiFi network

To go to the settings panel, open the browser and enter its IP address - where the entrance to the router is located. To authorize, enter the login and password admin/admin. How do I know them? They are used by default to enter the settings of the Asus router, and since we previously reset it with a “Reset,” I can say with 200% confidence that they will work.

The main page of the Asus Quick Setup Wizard will open. Click the “Go” button.

At the first stage, the software developer immediately takes care of access security - we change the router to the personal account.

After this, the firmware will independently try to determine your type of Internet connection:

  • Dynamic,
  • Static IP,
  • PPPoE
  • L2TP

You can find out it yourself from the contract with the provider. If the connection type is automatically determined correctly, click “Next”. If an error occurs and a different one is specified in the contract, then click on “Internet Type” and specify it manually.

Asus configurations for Beeline

The Beeline provider uses the type L2TP. Therefore, if you are their subscriber, then we select this particular type on the Asus router.

  • Username
  • Password
  • VPN server

They must be taken from the contract or obtained from technical support.

Internet connection Netbynet on Asus

Another popular provider, Netbaynet, provides services using the PPPoE, DHCP or Static IP protocols, depending on the client’s location.

Accordingly, you select the type indicated in your connection brochure. It is worth noting that with a dynamic IP (in Asus it is called “Automatic”), at Netbaynet you must check the “MAC Address Clone” checkbox

Since my Asus router is connected via the PPPoE protocol, then I need to enter authorization data.

Setting up wifi on the Asus RT-N12 router?

After this, we proceed to setting up the Asus router for WiFi distribution - we set a name for the wireless network and a password for connecting to it.

In the last step, we check all configuration parameters and exit the Asus Quick Setup Wizard.

That's all, actually. To make it easier to enter the settings of the Asus router, I added the address 192.168.1.1 to the bookmarks bar of the browser - now you can quickly go to the connection settings without entering it manually each time.

If you want to change something in your router after the first connection, then the Internet settings are located in the “Internet” section

And the parameters for connecting to WiFi can be changed by going to the “Wireless Network” menu