How to apply protective glass to a smartphone. Dust particles as a separate problem. How to glue protective glass on a Samsung phone

Many iPhone owners try to treat their device as carefully as possible. For this purpose, various covers, bumpers and protective glasses are purchased.

Here we will tell you how to glue protective glass as simply and quickly as possible without “defects” in the process.

How to do it

Before gluing the protective glass, remove the iPhone case. If the iPhone display is already covered with old film or glass, feel free to remove it. Wash your hands thoroughly to avoid getting dirt on the screen.

It is best to glue in a well-lit place so that you can see every speck that gets on the device screen. Well, choose the cleanest possible surface for gluing the glass.

Let's get started

Step 1. Cleaning the iPhone display.

To do this, we use any microfiber cloth so as not to leave anything unnecessary on the screen.

You can also use an alcohol wipe and then wipe the display with a soft microfiber cloth.

Step 2. Additionally, we clean the smartphone screen using the supplied tape or any other sticker.

Simply touch the display with tape and lift it back up. The adhesive surface will collect any remaining dust.

Step 3. Now you need to remove the protective film from the adhesive side of the glass and apply it to the screen.

Important: Hold the glass by the edges to avoid leaving unnecessary marks on it.

Step 4. Carefully place the glass on the iPhone screen.

If the glass is good, it will fit on the smartphone screen on its own. But to be extra sure, you can smooth it out yourself.

We run our finger through the center of the smartphone and begin to smooth it until all the bubbles are removed. If there are any small bubbles left, take a plastic card and, using light pressure, swipe it over the areas where the bubbles formed.

In this tutorial we used Mocoll glass. And it's not just like that

When you look sadly at your iPhone, the display of which is covered with a merciless mesh, it’s too late to think about protection. The manufacturer of protective accessories Mocoll took care of the consumer in advance.

All brand products are designed in such a way that the buyer spends a minimum of time gluing the protective glass.

Considering that the Chinese brand Mocoll () has been producing protective glass for several years, the company’s engineers have thousands of hours spent in research laboratories.

Glass is produced using high-tech equipment and receives a number of important properties during the processing process. Glass from Mocoll:

They have a thickness of only 0.33 millimeters. Glass is homogeneous and has equal thickness at any point. Among glass manufacturers, Mocoll has one of the lowest percentage of tolerances in production.

Mocoll glass easily withstands the impact of sharp objects and does not crumble into fragments upon impact.

Hardness at 9H on the Mohs scale. Only diamond is higher.

The glass has an oleophobic coating, so after gluing it you will not feel any tactile changes from interacting with the iPhone screen.

Mocoll supplies its products with a rich package. The kit has everything you need to glue glass without additional purchases or searching for a piece of fabric or plastic card to eliminate bubbles.

Mocoll has several options for protective glass. 2.5D, 3D and advanced development - 3D glass with elastic edges to match the color of the device’s body.

As you can see above, installing Mocoll safety glass is very easy. Due to the presence of a special silicone layer, you don’t have to worry about the appearance of hated bubbles during gluing.

For every taste, color and budget

Have you purchased a phone and want to protect the display? In this article you will find many tips to help you with this.

Any electronic device that has a wide enough screen must be protected from external factors. Gluing protective glass to a smartphone is especially important, since over time, the screen without it will be rubbed in places due to constant contact with the inside of the pocket. In addition, if you carry your phone in a bag or clutch, then the screen may get scratched from contact with other objects located there, so in terms of gluing the glass to the phone, the task also remains a priority. However, what can you also glue protection to to avoid mechanical damage? For example, on a tablet, for the same reasons as described above.

How to glue a protective glass on an iPhone

In the case of Apple products, the algorithm for gluing protective glass is usually the same. Regardless of the model, whether you have an iPhone 5, 5s or later models such as 6, 6s and even iPhone 7 and SE, the sequence of actions is the same:

First of all, you need to remove the case from the iPhone SE and carefully remove the old film/glass by the edge.
You should have a pre-prepared, spacious, flat place with good lighting.
Then, using a cloth that is used to clean the monitor, or a cotton pad soaked in any liquid with alcohol, wipe the screen clean. Under good lighting, you will clearly see how much this procedure has cleaned the surface, then wipe it dry with a cloth. This, of course, needs to be done with clean hands.
Remove the film from the adhesive side of the glass and adjust it to the size of the screen. In this case, you must strictly hold it by the edges to avoid the appearance of fingerprint marks.
Then you need to lower the glass and it will stick on its own.

How to glue protective glass on a Xiaomi smartphone

As you know, the mobile device market is now full of high-quality smartphones made in China. And if you bought yourself, for example, a model "Redmi 4 x", then you need to protect the display from various external factors that can damage it, so that your phone serves you faithfully throughout its potential shelf life. When gluing protective glass onto a Xiaomi smartphone, it is important to be careful; you need to do this on a flat surface and be sure to keep your hands clean.

How to glue protective glass on H onor 6c

On X Honor 6 SI and X Honor 9, the flagships of Huawei, which produces mobile devices, gluing the protective glass is done in the same way as on other models from this company. You shouldn’t be afraid to glue glass, because in such an algorithm the main thing is to be dexterous and do everything quickly and correctly, always under good lighting, which will make it possible to pay attention to all the shortcomings in gluing, such as dust particles that you could potentially miss at the stage cleaning the display before actual gluing.

How to glue protective glass on Meiza

Having purchased a smartphone model from Meizu, for example, Meizu M5, you need to protect your new purchase with protective glass. And it is not surprising, because the potential factors that lead to damage are, as a rule, extremely unpredictable, and protection in the form of such glass can neutralize most of them. It is necessary to glue glass carefully, strictly adhering to the algorithm, which in most cases is the same. It is important that the surface area of the glass when gluing is identical to the surface of the display, so that the edges do not extend beyond these boundaries. Having achieved this, the work of gluing glass can be considered complete.

How to glue protective glass on a ZTE phone

ZTE smartphones today occupy good positions relative to other models in the sales lists. Like other smartphones on the Android platform, they are exactly the same They also need display protection. And when gluing the protection to the screen, you must follow the rules described above in the same way. In addition, when gluing similar glass on Lenovo, the algorithm remains the same - you should be careful and pay attention to maximum sterility when working with glass. In addition, even if a protected smartphone is accidentally dropped on the asphalt, the glass, which is easily replaceable, will be damaged, but not the display, the replacement of which will cost much more.

How to glue protective glass on a Samsung phone

The displays of Samsung smartphones, for example, on models such as the J3 and A5, are also susceptible to mechanical damage, like any other. The algorithm is approximately the same as for other phones. You should be very careful when gluing so that no air bubbles get under the surface of the glass. They, of course, can be removed, but if you can glue the protective glass correctly the first time, you will definitely make your job easier. It is also important during the process to ensure that insidious particles of dirt and dust do not get onto the display at the time of gluing, however, if you did everything correctly, then such problems should not arise.

How to re-glue a screen protector on your phone

Has it ever happened to you that after gluing the glass, some of its edges still did not meet closely with the display? You can, of course, ignore this, but after a while these unadhered edges will play their role, and the glass will most likely fall off. That is why the question arises: is it possible to re-glue old glass? Of course, you don’t want to buy new glass because of your own mistake, so it’s easier to glue the existing one back on. In this work, first of all, accuracy is needed. After peeling off the glass, you need to hold it by the edges. The most difficult thing that can arise in this case is gluing the glass in place a second time. However, if you successfully managed to unstick it, then there shouldn’t be any problems.

How to glue the edges of the protective glass on your phone

If the protective glass does not fit at the edges, do not rush to despair, because there is still a way out. If a corner or several corners did not stick during installation and now there are huge white spots of air there, you need to carefully add a few drops of glycerin to the edge of the glass. It will fill all the air voids under the glass, and it will fit perfectly into place. In this way, the occurrence of such a problem is worth solving. In addition, during the process you can also clean the display of any debris that might have gotten under the glass during the process.

How to glue the protective glass on your phone if it comes off

If, after gluing the protection to the display, the glass suddenly comes off for no reason, then this problem needs to be solved. If you peel off the glass and glue it back, nothing bad will happen. The main thing, before gluing it a second time, is to make sure that there is no dirt or dust on the display, and it’s even better to wipe it again with a cotton pad and alcohol. This will protect the display from the reappearance of such unpleasant things on it and will save you from having to re-glue the glass. Therefore, it is still better to re-clean it in advance before gluing the peeled glass.

What to do if the protective glass is poorly glued

If you, having decided not to bother yourself, when buying a phone from the store employees, at the same time ordered the service of gluing the glass, and already at home, having re-printed the phone, you suddenly found out that it was glued to the display crookedly, then do not rush to get upset. In this case, you can re-glue it yourself the way it should be on the display. Using the tips from this article, you will definitely be able to ensure that the screen is always protected and is not affected by various external factors that may affect its integrity. Therefore, you should not quarrel with the store employees, because if you want something done well, then do it yourself!

How to properly glue protective glass

First of all, it is worth remembering that in such a matter it is extremely important to act carefully. This is the key to success, so you need to act decisively and quickly, but not mess up when gluing, otherwise you will have to re-glue, which, of course, is also quite simple, but takes a lot of time, which can be spent on something more interesting.

How to glue the protective glass to your phone yourself? You can easily carry out this operation yourself. To do this, you will need a little perseverance, a flat, well-lit surface and the protection itself that you are going to glue. When gluing, you must act carefully.

When buying a new smartphone, you want to preserve the presentation of the gadget for as long as possible.

That is why it is common to buy protective glass or films along with the phone. With their help, the device screen can be protected from chips and scratches that form as soon as possible. We tell you how to properly apply protective film or glass at home.

Protective glass or film: what to choose?

When choosing a defense mechanism, every user asks the question - which is better? It is impossible to answer this question unequivocally, since each means of protection has pros and cons.

Protective glass provides reliability when the phone falls, but at the same time increases its thickness. The film is practically invisible during operation, and is also much cheaper, but the level of protection is lower. Despite the differences in certain parameters (degree of protection, price, durability), the principle of gluing these elements is the same.

Most protective accessories have brief instructions on the sticker, but manufacturers are silent about some factors, so we’ll look at each point step by step.

Preparing the place and accessories

Prepare your work area. Wipe the table where the sticker process will take place. It is recommended to place a desk lamp above the phone to better see “problem areas” on the screen. Additionally, do not forget to wash your hands with soap and dry them.

The glass or film usually comes with tools. In most cases the kit looks like this:

The green “dry” bag is a dry cloth for cleaning the screen.
Pink “wet” bag – a wet wipe for cleaning the display.
A microfiber cloth that reduces the likelihood of picking up dust particles.

The first stage is cleaning the glass. Place your phone on the table. Pick up a napkin that says “wet” (sometimes it’s even numbered one). Wipe the smartphone screen with a damp cloth. Try to wipe the display so that not a single speck of dust is visible in the light.

The second stage is “drying”. Now take a second rag labeled “dry” (similar to the previous napkin, numbered two) and wipe the screen dry. Please note that your fingers should not touch the display.

The third stage is “intermediate”. Some manufacturers include an adhesive film in the kit to further rid the screen of dust particles. If you have such a tool, just stick it on the display and peel it off after a couple of seconds.

Working with glass

Pick up some protective film or glass. Look at her carefully. Manufacturers supply protective equipment with a special tongue to make it easier for a person to peel off the “sticky” part.

Having carefully peeled off the “adhesive part”, take the special glass by the “edges” and begin to slowly apply it to the phone. It is extremely important to ensure that the contours of the film and the screen match. While “aiming”, do not press on the display.

Release the glass. While it gradually sticks, make sure that there are no dust particles or bubbles anywhere. If no problems are found, effortlessly (lightly) swipe your finger across the center of the screen. If you notice any air bubbles, take a dry cloth and push them towards the edges of the display.

Once you are sure that there are no dust or air bubbles left under the glass, wipe the display again with a dry cloth.

Dust particles as a separate problem

There is a possibility of noticing a speck of dust after the procedure is completed. In such cases, you will need to re-raise the glass. This operation can be performed using a bank card. Additionally, take a small strip of stationery tape.

Pick up the edge of the glass that is closest to the speck of dust.
Place a piece of tape on the problem area
Quickly tear it away from the screen.
Return the protective glass to its original position.

In a modern smartphone, glass is the most vulnerable part of the design. Even the most careful handling of the device cannot always protect against small scratches and abrasions appearing on the screen over time. The display will have even less chance of remaining unharmed if it accidentally falls on asphalt or other hard surface.

Often, owners of mobile gadgets are confident that to protect the screen it is enough to stick a protective film on it. In fact, it will be much more effective to glue a special protective glass. This is much more complicated and somewhat more expensive, but your phone will receive reliable protection for the display from mechanical damage. Before we talk about how to stick protective glass on a phone at home, we will make a short review of one extremely attractive model, which, by the way, received high-strength protective glass Gorilla Glass 3. This is a phone.

Advantages of Wileyfox smartphones

It is worth paying special attention to the devices of this young British brand, since each model has the following advantages:

Ability to work with two SIM cards;
Support for 4G LTE data networks;
High quality assembly and components;
Original stylish design;
Powerful hardware component;
Affordability.

All this was appreciated not only by users. The company's products have attracted the attention of experts. After appearing on the market in October 2015, in December Forbes magazine named the Wileyfox Swift smartphone of the year. In February 2016, the company won first place in the manufacturer of the year category at the prestigious British Mobile News Awards 2016. In October 2016, the Wileyfox Spark+ model, according to the authoritative online publication Hi-Tech Mail.ru, became the best smartphone under 10 thousand rubles.

Briefly about Wileyfox Swift 2

The phone attracts attention with its stylish original design and excellent technical characteristics. The device has everything that modern smartphones can have: a fingerprint scanner, Glonass, GPS and Assisted GPS navigation modules, as well as an NFC module. The model runs on a powerful and productive eight-core Qualcomm Snapdragon 430 MSM8937 processor with a frequency of 1.4 GHz.

The phone has 2 GB of RAM and 16 GB of internal memory. If necessary, free memory can be increased by installing a microSDXC card of up to 64 GB into the device. The model has a 16-megapixel main camera module, with which you can take high-quality photos and shoot videos. There is an 8-megapixel front camera for selfies.

You can study the characteristics and capabilities of the model, ask clarifying questions and order the phone for only 9,990 rubles on the Wileyfox website.

Before we figure out how to glue protective glass onto a phone at home and without the help of a technician, we’ll find out what kind of accessory it is and why you need to glue glass on a phone in the first place. The glass is designed to protect the display from possible mechanical impacts. Thanks to its flexible structure, glass is able to absorb direct impacts. During the production process, the protective glass on the phone is tempered and chemically treated. For this reason, protective glass is much better able to protect the screen from scratches, cracks and chips than protective film. Glass is thicker than film and has a harder structure. Protective glass is not afraid of direct impact from sharp objects - its surface can be scratched with a sharp knife or keys without consequences. Even if you drop your phone or a heavy object accidentally falls on it, the glass will only become cracked, but the screen of the device will remain intact.

It is worth emphasizing that the protective glass consists of five layers: a flexible silicone base, restraining and anti-reflective layers, the protective layer itself and an oleophobic coating. Due to its properties, glass, if carefully glued to the screen, does not reduce image quality and does not affect the comfort of operating a smartphone. The only thing you should know before gluing glass to your phone is that the device will weigh a little more.

What do we need to glue the protective glass onto the phone ourselves? Before gluing it, prepare the following items:

Wet and dry wipes;
Screen cleaner;
Stationery tape;

1. Preparation of the workplace

Make room on the table so that when you start gluing the glass onto the phone, there are no foreign objects in the way under your hands. Wash and dry your hands thoroughly before starting work. Wipe the surface of the table from dust and take care of organizing effective lighting for the workplace.

2. Screen cleaning

Before sticking the protective glass on the screen, clean it from dust and fingerprints. Dampen a regular napkin in a special liquid and wipe the surface of the screen. You can also use special wipes for cleaning displays. After this, wipe the screen with a clean, dry cloth. Sometimes regular office tape is used to remove dirt and dust. But after this, the screen must also be thoroughly wiped.

3. Glass installation

We begin to glue the protective glass. We take the glass out of the packaging and remove the shipping film from it. Carefully holding the glass by the edges, we adjust it to the edge of the smartphone screen. Gradually lower the glass and lightly press it against the screen with a dry cloth. There is no need to try to stick the protective glass on as quickly as possible. Carry out all operations carefully and slowly.

4. Final stage

It is not always possible to immediately glue the protective glass in such a way that there are no “bubbles”. This happens because small air droplets remain between the surface of the screen and the protection. It's not a problem. Immediately after gluing, use a dry cloth to disperse them, pressing from the center to the edges. But if dust gets under the protective glass, you will need to carefully bend its edge and remove dust particles using stationery tape.

Conclusion

So, we figured out how to stick protective glass on your phone yourself. Remember - the process requires high concentration and will take some time. Start it if you are not in a hurry and there are no distractions. By gluing protective glass, you can protect an expensive screen for a small budget (no more than 500 rubles) and in the future save money that may be required to replace it in the event of mechanical damage.

“Protective glass for a phone: how to glue it?” - a similar question interests a considerable number of users. Firstly, let us immediately note that the process of installing protective glass for a smartphone has some subtleties, but overall it does not seem to be anything overly complicated. Even if you have never done this before, you can achieve the same result as you would get in service centers or in cellular communication stores, with the only difference being that the installation of protective glass in the above-mentioned companies is a paid service. All that is required from the user himself is a set of tools and a little attention.

Protective glass for your phone: how to glue it

Many users who are faced with the need to carry out such an operation do not even suspect that not only the correct sequence of actions plays an important role here, but also a well-prepared workplace. If there is a mess on the table, and materials and tools are scattered, it will be more difficult to achieve a good result. The more quickly you can use one or another element, the better the gluing will be. Therefore, make sure in advance that all unnecessary components are removed from the workplace or at least moved outside the operation. So, here we have it on the phone. We'll tell you how to stick it a little lower, but for now let's talk about what it is and how it differs from film.

Differences between glass and film

Users usually clearly understand which of these materials they are talking about. However, some people do not understand the basic differences between film and safety glass. Let's talk about this in more detail. The second material better withstands mechanical loads. If you drop such material, only the glass will be damaged. It can be replaced later. But if an ordinary film was glued to the device, then everything is much more serious. This may require a complete screen replacement. And it will cost an order of magnitude more. For the sake of fairness, we note that glass is not afraid of sharp objects. You can run keys, a knife, scissors across it - anything. But it will not receive any damage. This, unfortunately, cannot be said about the film. Finally, I would like to note that gluing glass is much easier. Well, now let’s move on to consider the question of how to install protective glass on a phone in more detail.

Preparing the screen

Before installing the protective glass on your phone, you should carefully prepare the display surface for this operation. The process will consist of several basic steps. If you have previously applied it to the screen, you need to remove it by pulling the edge. We will no longer need the film in the future, and it can be thrown into the trash. We open the kit with protective glass. It should contain a cloth made of microfiber. We will need it later. If the package does not include an alcohol-preserved rag, then you can wet the wet disk with it, after which you should wipe the screen. You can wait until the display is dry and then use a microfiber cloth as intended. Before starting such work, it is recommended to wash your hands with soap to avoid the appearance of greasy stains on the screen. Once the screen is clear, you can move on to the next step. So, we continue to answer the user’s question about how to use it protectively.

Installation

When you pick up the protective glass for your phone, you will see that it is covered on one side with a special layer of film. This is the adhesive side with which the element will need to be applied directly to the device screen. Now we remove the film, preparing the glass for the gluing process. It should be held not by the surface, but by the edges, in order to avoid loss of properties. When you align the glass, press it against the screen itself. The coating of the first one is made in such a way that nothing additional needs to be done, it glues itself.

We complete the operation and remove the air

Once you install the screen protector on your phone, you will notice that there are small bubbles underneath. This is the air remaining inside. You can remove it quite simply. To do this, smooth the glass from the center in the direction of the bubbles. Thus, they can be “squeezed” abroad. In the end, you will get an element that sits perfectly on the surface of the screen. Some users ask the question of how much protective glass for a phone costs. Note that the price for it falls in the range from 300 to a thousand rubles, depending on the brand and quality, as well as on the phone model. Now, after reading this article, you know the answer to the question of how to apply protective glass to your phone, how to glue it correctly.

Which protective glass to choose

Currently, a considerable number of companies are engaged in the production of such accessories. Nevertheless, protective glass from Ainy is rightfully considered the best of them. Why? What is the best protective glass for your phone? The products of this company have proven themselves well in numerous tests. Experts especially closely monitored the behavior of glass installed on devices of the American company Apple. It was found that with a relatively small thickness, the accessories provide excellent protection of the screen from external mechanical influences. It should be noted that the glasses of this company are made of five layers, the final one being oleophobic.

Func, for example, produces similar products. Its products are in approximately the same price category. It was noted that many accessories are hardened, but the quality and level of protection do not match the elements from Ainy, which, in principle, was confirmed by endurance tests.