The keyboard turns off on an asus laptop. Enable, configure and disable the laptop keyboard

The laptop keyboard rarely requires attention: if you haven’t broken it, filled it with liquid or changed it, then it works without problems. But sometimes the question of how to turn on the keyboard on a laptop becomes relevant for users - there are no prerequisites for the device to break down, but the keys stop working.

Diagnosing the problem

There is an easy way to check if the keyboard is working: restart the laptop and go into the BIOS. If the buttons work in the BIOS, then the error must be looked for in the software.

Roll back to a point where the keyboard was working correctly.
Run a virus scan.
Roll back your keyboard drivers or install the latest version.

If the keyboard does not print on the laptop (individual keys do not work), check whether the cause of the incorrect operation is excessive contamination of the device. Using a can of compressed air, remove small items stuck in the grooves.

If the keyboard turns off, check the USB ports, the RJ-45 connector (for the network cable) and the touchpad. If they don't work either, then the motherboard is faulty.

If the ports are working, then check the cable of the keyboard itself. Gently pry the latches to remove the module. Disconnect the cable and clean its contacts - they may have oxidized. After cleaning, reinstall the cable.

On some laptop models, the keyboard cannot be removed independently - for example, on the ASUS X550C there is no separate module; The buttons here are recessed into the body.

Enable the numeric keypad

Sometimes not the entire keyboard does not work, but only the number pad, which is located on the right. When it is disabled, numbers are not dialed: the buttons perform other functions - for example, they work as navigation keys.

To turn on the side number keyboard, press the Num Lock key. It allows you to activate the right keyboard: the numbers are unlocked and you can type them. If there is no separate block, and the numbers themselves are located on some keys with letters, then you can unlock the numeric keypad using the combination Fn+F11.

Be careful: on some ASUS laptop models, this combination reduces the sound. See how to unlock numbers in your laptop instructions. If there are no instructions, carefully examine all the keys in the F1-F12 row - they have icons that indicate the purpose of the button.

Using the virtual keyboard

If you haven’t figured out how to turn on the keyboard on a laptop or activate the number pad, then use an alternative solution - a virtual input device. The on-screen keyboard was already available in Windows XP, so there are no problems with its launch in later versions either.

To enable the virtual keyboard:

Open the Start menu and use the built-in search (useful on Windows 7).

Open the section “All Programs” - “Accessories” - “Accessibility”.
Press Win+R and execute "osk.exe".

On Windows 8, you can add a touch keyboard icon to the taskbar. It will be pinned near the system tray.

Right-click on the taskbar.
Expand the "Panels" section.
Add a touch keyboard.

On Windows 10, the order has changed slightly: you need to click on the taskbar and select “Show touch keyboard button.”

To enable numeric dialing mode, click the Options button and check the Enable numeric keypad option. The “NumLock” key will appear on the right - press it to make the number pad appear. This method works on all models, regardless of the manufacturer, be it Acer, Samsung, HP, Lenovo or any other brand.

Disabling the keyboard

In some situations, the keyboard built into the laptop stops working. For example, after liquid gets in, some keys fail. You can simply connect an external keyboard, but then it will be inconvenient to work. So let's see how to disable the built-in input device if a USB keyboard is already connected.

Launch Device Manager.
Open the properties of the built-in keyboard and go to the "Driver" tab.
Select the Hardware ID property and copy the first line.

Now you need to establish a ban on the use of equipment. Let's look at the example of Windows 7:

Press Win+R and execute “gpedit.msc”.
Go to “Computer Configuration” – “Administrative Templates” – “System” – “Device Installation” – “Device Installation Restrictions”.
Double-click on “Prohibit installation of devices with specified codes.”
Enable the option and click Show.
Paste the copied hardware code and click OK.

For maximum effect, remove the keyboard in Device Manager. Once the system is restarted, the built-in input device will no longer work. Connect an external keyboard and use it calmly. If you need to enable the laptop's native keyboard, open the Group Policy Editor again and disable the above option.

At first it seems strange that sometimes a user needs to disable the keyboard on a laptop. After all, this is an integral and important part of the device. However, there may be many reasons for such a procedure. For example, you have children who like to play with a laptop in your absence. Then this measure is one of the ways to protect the device. Or the keyboard itself has malfunctioned (water was spilled on it, some key gets stuck, etc.), making it impossible to use the device. Whereas by disabling the button control, you can use the laptop for your own purposes without any problems. Only using a mouse, touchpad, or connecting an external keyboard via USB.

Most often, you need to “de-energize” the keyboard on a laptop temporarily. That is, literally for a couple of minutes - maximum an hour or two. For example, to let a child watch a cartoon. But at the same time so that he could not press anything. In this case, the best option is to use the command line. All you need:

Launch the command line as an administrator account. This can be done in different ways. In Windows 10, you should hover over Start, then right-click and select the appropriate item.
Next, enter the command “rundll32 keyboard, disable”. Press Enter.
After which the laptop keyboard will stop functioning.

This method is extremely simple. At the same time, you can also enable the keyboard through the command line. You just need to enter “rundll32 keyboard, enable”.

Disable the laptop keyboard through the device manager

Another method is no less popular. It also allows you to quickly disable the built-in keyboard on your laptop. What is needed for this? You will need a device manager. In addition, you will need to do the following:

We go to the device manager. To do this, in Windows 8 and 10, right-click on Start. Then select the line of the same name. On a laptop with Windows 7, the easiest way is to press the Win+R key combination and enter the command “devmgmt.msc”.
As soon as you get into the device manager, look for the keyboard in the list. Right-click on the desired item (most often it is labeled “Standard Keyboard”).
In the next window, select “Disable”. If there is no such option, then click on “Delete”.
Next, confirm disconnecting the device.

We use various software

Those who do not have enough built-in capabilities and tools to disable the keyboard on a laptop can use various programs and utilities. For example, we can recommend Toddler Keys. Its advantage is not only its convenient and simple interface. This utility is free. It is also compatible with a wide variety of operating systems and laptop models from any manufacturer - asus, lenovo, acer, hp, samsung, etc.

Using the Toddler Keys app is quite simple:

Download the utility from the developer’s website or a third-party resource.
We install it on the laptop.
Let's launch the program. It will open at the bottom right in the tray (notification area).
Next, find the utility shortcut. These will be the letters "T" and "K" in blue. Click on it with the secondary mouse button.
A window will pop up. In it you need to click on “Lock Keyboard”. As a result, a check mark will appear next to this item.

Accordingly, when you need, on the contrary, to turn on the keyboard, then simply uncheck the box. We also recommend that you pay attention to the following. After installing the application, uncheck the “Lock Drive Doors” and “Disable Power Button” checkboxes. They are installed by default, blocking the DVD/CD-ROM and the laptop's on/off button.

Another free app to disable your keyboard is Kid Key Lock. This program compares favorably with other software in that you can set blocking modes in its options. For example, you can completely disable the entire keyboard, or a single key or just a group - the same function keys.

How to disable individual keys?

Sometimes it is necessary to “disable” not the entire keyboard, but only individual buttons. How to do it? Let's look at a couple of options:

You need to disable the number keys on the right side of the keyboard. It's simple. Press and hold the Fn and NUM LOCK buttons. On some devices, you only need to press the second key. Sometimes you can disable the numeric part of the keyboard using the “Fn+F11” combination.
Sometimes you need to disable hotkeys. To do this, press the combination “Win + R”. In the window, enter “gpedit.msc”. Then click OK. Go through the menu tree to “User Configuration”. Next we need the “Administrative Templates” subsection. In it, click on “Windows Components”. Next, look for “Windows Explorer”. On the right we find “Disable Windows key combinations + X”, click on it 2 times. In the window that opens, check the “Enable” box. Click OK and .

How else can you disable the laptop keyboard?

In fact, everything that we described above are ways to temporarily disable the keyboard. Literally rebooting or deleting the software will return it to working condition again. Therefore, it is advisable for an advanced user to know how to disable the keyboard for a longer period. For example, to replace it with a new one.

As an option – physical shutdown. You need to remove the back cover of the laptop. Find a wide and large cable that goes from the keyboard to the motherboard. Then carefully disconnect it. The procedure requires great care. After all, one awkward movement and you can scratch the same motherboard, and this is fraught with big problems.

By the way, finding the keyboard cable itself on some laptops is not easy. After all, it is located differently in all models. Much here depends on the manufacturer of the motherboard (Gigabyte, Intel, MSI, etc.) and the device itself (Asus, Acer, Sony, Dell, etc.).

Can also be used to disable the keyboard Windows Group Policy Editor. It is available by default in the “seven” (except for Home). In some basic versions of Windows 8 and 10, you will most likely need to additionally install the Group Policy Editor. This is not difficult to do - there is a lot of information on the Internet on this topic. So let’s get back to how to disable the keyboard using this tool (using Windows 10 as an example):

Go through the start menu to the control panel. Select the large icons view mode.
Click on device manager. In it we find the keyboard item. Click the mouse (right button). Then select “Properties”.
Go to the “Details” tab. In the list we find ID equipment.
In the value field, copy the appeared data (ID).
Without closing this window, press the “Windows + R” combination. Enter the command “gpedit.msc” and press Enter.
The editor will open. To avoid searching for a long time for the required section, namely “Restrictions on device installation”, we recommend going to: Computer Configuration/Administrative Templates/System/Device Installation.
Then on the right side we find the item “Prohibit the installation of devices with the specified codes.” “Click” on it twice.
Activate the “Enable” checkbox.
Next, click the “Show” button in the “Options” section.
A window will open. You need to paste the previously copied value into it.
Again, in the “Options” section, check the box next to “Also apply to relevant devices...”.
Save all changes (via “Apply” and “OK”). Reboot the device.

This is not the easiest way to disable the keyboard on a laptop with Windows 10 (or any other OS). However, this option for deactivating the keyboard is great if you need to replace it.

Conclusion

Choose any of the methods you like. However, if you are a novice user, it is better to use standard Windows tools or third-party software to disable the keyboard. It is difficult to make a mistake and do something wrong here. But working with the local group policy editor, and even more so resorting to physically turning off the keyboard, is only worth it as a last resort.

If you have a laptop, then the keyboard and touchpad on it are important components, without which working on the device will be difficult. Of course, there are alternatives in the form of keyboards and mice that connect via USB, but that’s not about that now.

If you are going to replace the keyboard or you put an external one on top of it, which can press on the laptop keyboard, thereby interfering with comfortable work, the question arises, how to disable the keyboard on the laptop? It is possible that the keyboard is so damaged that it may cause defects in the operation of the computer, so it needs to be disabled altogether. In this article we will look at issues such as temporarily disabling the keyboard and disabling it permanently.

Temporarily disabling the laptop keyboard

At this point, there are again two options for disabling: standard, that is, using Windows tools and using third-party utilities.

Disabling the keyboard using the command line

Open a command prompt as administrator and run the following command:

rundll32 keyboard, disable

After this action, your keyboard will not work and cause inconvenience. You can re-enable it using a similar command:

rundll32 keyboard, enable .

How to disable the keyboard using programs?

There are many different programs for disabling the keyboard, so I won’t list them all, but will tell you about Toddler Keys. If you wish, you can enter “Programs to disable a laptop keyboard” in a search engine and see other options.

So, download Toddler Keys and install it. After installation, launch the program from the control panel. The icon will be indicated by black letters “TK”.

Right-click on this icon and select the item from the drop-down menu "Lock Keyboard". After this, the keyboard should stop responding to presses.

In addition to this, you need to do a couple of actions: uncheck the items Disable Power Button And Lock Drive Doors. For those who don’t know English, I’ll explain that these two parameters block the laptop’s on/off button and the disk drive.

To re-enable the keyboard, you need to uncheck the corresponding box in this program, that is, from “Lock Keyboard”.

How to disable a laptop keyboard permanently?

Perhaps the keyboard is physically damaged, many keys do not work, or there is another reason. Then you can disable the keyboard permanently. More precisely, not at the physical level, since after reinstallation the keyboard will be turned on again.

You can completely disable the keyboard permanently using the Group Policy Editor. I want to say one important point - this option is only available in professional versions of Windows, but not in basic and home ones. In Windows 7 it is installed by default in all editions.

To get started, open Control Panel. This can be done through the Start menu, or right-click on the Start menu and select "Control Panel". Switch the display mode to large icons and find there "Device Manager". By the way, you can still open it if you right-click on Start, there is also this option there.

Open the tab "Keyboards" and right-click on the device, selecting "Properties".

In the window that opens, go to the tab "Intelligence", and in the “Property” drop-down menu select "Equipment ID". After that, copy the first line of the value. We don't close the window.

Now open the Group Policy Editor. To do this, press Win+R and enter the command.

On the right side of the window we can prohibit the installation of devices. The item is called “Prohibit the installation of devices with the specified codes.” Right-click on this and select “Edit”.

Turn on this function and click on the “Show” button at the bottom. Paste the copied keyboard ID into the window that opens and click OK.

Don’t forget to check the box below the “Show” button, it’s called "Also apply to corresponding devices that have already been installed". Apply all the changes and exit the Group Policy Editor.

Now you need to restart your computer. The keyboard will work only after reinstalling the system. If this method seems complicated to you, you can stop at the first two options of this article.

There are situations when you need to disconnect the keyboard from the computer, for example, if it is damaged or simply to prevent accidental pressing of the buttons. On stationary PCs, this is done simply by disconnecting the plug from the socket of the system unit. But with laptops everything is not so simple, since the keyboard is built into them. Let's figure out how you can still disable it for the specified type of computer device with the Windows 7 operating system.

There are several ways to disable the keyboard on a laptop. However, they all work on desktop PCs. But when it is possible to simply pull the cable out of the connector of the system unit, there is no particular need to use the methods presented below, since they seem more complex. All of them are divided into two groups: performing a task using standard system tools and using third-party programs. Next, we will consider in detail each of the possible options.

Method 1: Kid Key Lock

First, let's consider the possibility of disabling the keyboard using third-party programs. There are quite a few computer applications for these purposes. We will study the algorithm of actions in one of the most popular of them - Kid Key Lock.

After downloading the Kid Key Lock installation file, run it. English language will open "Installation Wizard". Click "Next".

A window will open in which you can specify the installation directory. However, changing it is not at all necessary and is not even recommended. So press again "Next".

Next, a window will appear where you can enter the name of the application shortcut in the start menu (by default "Kid Key Lock") or remove it from there altogether by placing a mark next to the position "Don't create a Start Menu folder". But, again, we advise you to leave everything unchanged and click "Next".

In the next step, by checking the checkboxes next to the corresponding inscriptions, you can install application shortcuts to "Desktop" and in the quick launch menu, as well as enable Kid Key Lock autoloading at system startup. By default, all checkboxes are unchecked. Here the user, at his own discretion, must decide what he needs and what he doesn’t, set the marks, if necessary, and then click "Next".

Now that all the data has been entered, all that remains is to start the installation by clicking "Install".

The installation procedure itself will take a few moments. Upon completion, a window should appear informing you that the process was successfully completed. If you want to launch Kid Key Lock immediately after closing "Installation Wizard", then leave a mark next to the parameter "Launch Kid Key Lock". Then click "Finish".

If you left a mark near the inscription "Launch Kid Key Lock", the application will start immediately. If you have not done this, you will have to activate it in the standard way by double-clicking on the shortcut on "Desktop" or in another place, depending on where the icons were installed when entering the installation settings. After launch, the software icon will appear in the system tray. To open the program management interface, click on it.

The Kid Key Lock interface window will open. To lock the keyboard, move the slider "Keyboards Locks" to the extreme right - "Lock all keys".

Next click "OK", after which the keyboard will be locked. If necessary, to turn it on again, move the slider to its previous position.

There is another option to disable the keyboard in this program.

In addition, in this program in the section "Mouse Locks" You can disable individual mouse buttons. Therefore, if some button stops working, check the application settings.

Method 2: KeyFreeze

Another convenient program for disabling the keyboard, which I would like to dwell on in detail, is called KeyFreeze.

As you can see, this method is simple, which many users like.

Method 3: "Command Line"

To disable the standard laptop keyboard, there are also methods that do not require installing third-party software. One such option is to use "Command line".

Click "Menu". Open "All programs".

Go to the directory "Standard".

Having found the inscription "Command line" click on it RMB and click "Run as administrator".

Utility "Command line" activated with administrative privileges. Enter into its shell:
rundll32 keyboard, disable

Apply Enter.

The keyboard will be disabled. If necessary, it can be activated again via "Command line". To do this, enter:
rundll32 keyboard, enable

Click Enter.

If you have not connected an alternative input device to your laptop via USB or another connector, you can enter the command by copying and pasting using the mouse.

Method 4: Device Manager

The following method also does not involve the use of installed software to achieve the goal, since all the necessary actions are performed in "Device Manager" Windows.

Click "Start" and go to "Control Panel".

Choose "System and safety".

Among the block items "System" go to "Device Manager".

Interface "Device Manager" will be activated. Find the item in the list of devices "Keyboards" and click on it.

A list of connected keyboards will open. If only one device of a given type is currently connected, then there will be only one name in the list. Click on it RMB. Select "Disable", and if this item is not there, then "Delete".

In the dialog box that opens, confirm your actions by clicking "OK". After this, the device will be turned off.

A logical question arises: what to do if the standard input device, disabled in this way, needs to be activated again. Click on the horizontal menu "Device Manager" position "Actions" and select an option "Update hardware configuration".

Method 5: "Group Policy Editor"

You can also deactivate the standard data input device using the built-in system tool called "Group Policy Editor". However, this method can only be used in the following editions of Windows 7: Enterprise, Ultimate and Professional. But it will not work in the Home Premium, Starter and Home Basic editions, since they do not have access to the specified tool.

But first of all we will need to open "Device Manager". How to do this is described in the previous method. Click on the item "Keyboards", and then RMB Click on the name of a specific device. From the list that appears, select "Properties".

In a new window, go to the section "Intelligence".

In field "Property" select from the drop-down list "Equipment ID". In area "Meaning" The information we need for further action will be displayed. You can write it down or copy it. To copy, click on the inscription RMB and select "Copy".

You can now activate the Group Policy editing shell. Call the window "Run" by typing Win+R. Enter in the field:
Click "OK".

The shell of the tool we need will be launched. Click on the item "Computer Configuration".

Next, select "Administrative Templates".

Now you need to go to the folder "System".

In the list of directories, enter "Device Installation".

Then go to "Device Installation Restrictions".

Select item “Prohibiting the installation of devices with the specified codes...”.

A new window will open. Move the radio button to position "Turn on". Place a checkmark at the bottom of the window opposite the item "Also apply...". Click on the button "Show…".

A window will open "Entering content". Enter in the field of this window the information that you copied or wrote down while in the keyboard properties in "Device Manager". Click "OK".

Returning to the previous window, click "Apply" And "OK".

After this, reboot your laptop. Click "Start". Next, click on the triangle icon to the right of the button "Shutdown". Select from the list.

After restarting the laptop, the keyboard will be disabled. If you want to turn it on again, go to the window again "Prohibit installation of devices" V "Group Policy Editor", set the radio button to position "Disable" and click on the elements "Apply" And "OK". After rebooting the system, the standard data input device will work again.

As you can see, you can disable the laptop keyboard in Windows 7 using standard methods or by installing third-party programs. The algorithm of the second group of methods is somewhat simpler than operating with the built-in tools of the system. In addition, the use "Group Policy Editor" is not available in all editions of the OS being studied. But still, the use of built-in utilities does not require the installation of additional software, and the manipulations that are necessary to perform the task with their help, if you look at it, are not so complicated.