Set up tricolor TV programs. Self-tuning of the TV: Tricolor TV. Let's move it a little bit

After purchasing Tricolor TV satellite equipment, the first step is to assemble and install the antenna. The company's employees take care of the connection themselves, but if the subscriber wishes, they can set up Tricolor TV independently.

The quality of the signal received from the satellite depends on the correct location of the antenna. An important condition is direct visibility of the information signal beam from the satellite to the dish. If it is not possible to mount the antenna on the wall next to the window of the apartment where the satellite receiver will be installed, a rational option would be to install the antenna system on the roof of the building. It is prohibited to place the antenna on a balcony or indoors.

Satellite dish assembly

Based on the included instructions, you need to assemble the plate and securely fasten it with suitable fasteners. A television cable is connected to the receiving device located in the holder, which should be secured to the bracket with ties.

An F-connector is screwed onto a 1.5 cm cable stripped of insulation from both ends. Next, you need to connect the receiver to the antenna converter and configure it using the remote control.

Settings

After pressing the “Menu” key, in the section of the main menu displayed on the TV screen, you should go to the “Settings” line, and then to “System settings”. At this point you need to enter the correct time for the region. The desired satellite name will be displayed in the “Satellite” item. In the “Search type” line you need to set Tricolor TV.

Once the satellite is selected, you should confirm the selection by pressing “OK”. If the actions are performed correctly, two scale bars will appear on the screen, characterizing the signal level and its quality. For excellent broadcasting of channels, the parameter values should not be lower than 70%, otherwise the picture quality will deteriorate or the broadcast will be unstable. By changing the angle of the antenna mirror, you need to achieve maximum signal characteristics. It is important to wait a few seconds after each adjustment step. This action is provided so that the signal has time to change.

After successfully installing the dish, it is necessary to securely tighten the fasteners of the antenna structure, otherwise it will move in strong winds. It is also possible that the signal may deteriorate during precipitation. Before exiting the menu, you need to save the settings.

Connecting the receiver

The Tricolor TV receiver is connected in two ways:

high frequency (HF) connection using an antenna cable;
low-frequency (LF) connection using a regular cable with bell or scart ends.

Having selected an RF connection, the receiver’s output (indicated as “RF Out”) must be connected to the antenna socket of the TV. Next, you need to connect the receiver to voltage and turn on the power button. If everything is done correctly, the word “BOOT” will appear on the monitor, as well as the channel number. Now you need to run an automatic channel search to find the channel with the line “No Signal”. The presence of this phrase will indicate that the device is connected correctly.

The LF connection uses a cable with “tulips” or “skart”. After the same message appears on the screen, you should set the video mode on the TV remote control with the “A/V” button. The appearance of the message “No signal” indicates that the receiver is connected correctly.

Checking the reception of a satellite signal by the receiver is carried out by displaying any channel on the screen. Its number, time and name of the program that the satellite is currently broadcasting should be displayed. Since the antenna is not aligned, the background image on the screen will appear blue.

After pressing the “i” key, both signal adjustment scales will be displayed on the screen. The plate needs to be adjusted to the maximum. The exact direction of the antenna to the south will help you make precise adjustments yourself. The presence of nearby neighboring antennas facilitates the correct direction of the dish and its tilt.

After the most advantageous antenna position has been found, click “OK” and the Tricolor TV channels will automatically be added to the receiver menu. They need to be preserved.

In order to find free channels, as well as those not included in the package, you need to select “Settings” in the menu, enter the digital code 0000 and go to automatic search.

In this case, the search type should be set to “Network” and the line “Skipping encoded channels” should be highlighted. Next, press the “Search” button. After completing the registration of programs, you need to save the list. If desired, the subscriber can sort channels alphabetically.

Ways to troubleshoot possible setup problems

If there is no signal, the first thing you should do is look at the power supply to the receiver, its connection to the TV, the integrity of the cable, and the tightness of the connectors. It is recommended to press the “AV” button on the TV remote control more than once, since there is more than one input.

If the “Tricolor TV” menu appears on the screen and at the same time the message “No signal” is present, then communication with the satellite is not established. The antenna needs to be adjusted. Another option may be operator-administered prophylaxis.

On any channel, the message “Coded channel” appears, indicating that access has not been paid for or the receiver is not registered. Encoded signals are included in the overall package or broadcast separately. Such channels are considered the property of the provider and therefore require paid decoding.

After completing the setup, when turning on the receiver, the subscriber is prompted to download an update indicating the full list of channels.

Newly purchased equipment must be registered with Tricolor TV.

Registration of receiving equipment

After completing the antenna setup, you need to press the “Exit” button twice to exit the menu. On the company's official website you need to fill in the user and receiver data. Equipment installation can be registered by calling the company number listed on the website.

Malfunctions can occur in the operation of any equipment, and Tricolor TV receivers are no exception to this rule. There are situations when channels from paid packages disappear on a set-top box, and it becomes impossible to use the television service. Fortunately, to fix this problem it is not at all necessary to call a technician from Tricolor TV. Setting up channels on your own will take very little time, even for an unprepared subscriber.

Checking the satellite signal

Despite the fact that the Tricolor company provides its specialists for installing and configuring equipment, many subscribers prefer to carry out these operations on their own. As a result, when you first start using the dish, there are often failures in receiving a signal from the satellite. This may cause broadcast interference and loss of TV programs. Therefore, before moving on to the settings, it is worth checking the signal level at the antenna.

How to check the signal?

To check the signal level from the satellite, you need to press the “i” key on the receiver’s remote control twice. After this, two scales will appear on the screen:
Signal quality;

For normal operation of the system, their readings must be at 70%. If the scale values are smaller, it is worth carrying out additional antenna tuning. Its position is changed until the scale readings become satisfactory.

Important! Often, when setting up on their own, subscribers set the scale values to the minimum. As a result, with the slightest change in weather (cloudiness, precipitation, etc.), the receiving capacity of the antenna drops and broadcasting disappears. It is necessary to try to bring the level and quality of the signal to at least 85% in order to be insured against such troubles.

Recovering a missing broadcast

If the satellite signal is normal, you will have to carry out some operations with the receiver. Step-by-step setup of Tricolor TV channels will look different, depending on how the equipment behaves. There are two options:

all TV channels disappeared;
only one is displayed.

Let's take a closer look at the actions in each situation.

There is no channel

If there is no broadcasting on all frequencies, you need to press the “Menu” button on the remote control and go to the settings section. Depending on the receiver model, it may be called either “Settings” or “Applications”.

Next in this section, using the remote control, you need to find the “Search for channels...” subsection and go into it. The equipment will carry out search operations for some time. Then a list of found channels will be displayed on the screen. The set-top box will offer to save them - this must be done so that you do not repeat the described operations each time you turn it on. To save, just click the “Yes” button in the pop-up dialog box.

One channel displayed

There are situations when, as a result of some user action, broadcasting disappears on all frequencies except one. In this case, the receiver shows a channel with the name “View instructions”, and all other programs included in the package are missing. Resetting the TV set-top box to factory settings and then restoring it will help here.

To reset to factory settings, you need to press the “Menu” button on the remote control and go to the “Settings” or “Applications” section (depending on the receiver model). In this section, select “Factory settings” and press the OK button. To confirm the reset, you will need to press the Info or F1 key on the remote control, and then select the answer “Yes” in the dialog box that appears.

During the reset process, the set-top box will automatically reboot. At the end of this process, a message about the identification of the remote control will appear on the TV screen with a recommendation for pressing the desired button. The recommendation should be followed, after which a table of settings will appear on the screen. It will not cause any difficulties for subscribers who installed the equipment themselves, since they have already encountered it. For the rest, we'll tell you a little more:

in the “Selection of languages” table, select Russian as the menu and audio language1;
audio2 language can be left unchanged;
in the “Operator” section select Tricolor TV;
in the “UTC Shift” section, select your time zone, or the one closest to it;
in the line “Update from satellite” set the value “Yes”;
in the “Automatic search” section in the “antenna” line, select “Tricolor TV”.

Important! If the set-top box is connected to the antenna according to a standard scheme, you do not need to correct the default values in the last section.

Separately, the rules for setting up the region should be noted. The subscriber is offered three options:

basic;
MSK +0;
MSK +2.

You should not select the first item, otherwise the receiver will save only one info-TV channel, and the others will be unavailable. If you select the “+0” option, the broadcast will be conducted according to Moscow time. If you select “+2”, the programs will be available with a two-hour shift from Moscow. You should set one of these two types of time zones based on your own convenience.

At this point the settings are considered complete. After saving them, the set-top box will begin automatically searching for available channels. Based on its results, a list of what was found will be displayed on the screen, which the subscriber will only have to save. To do this, you will need to click the “Yes” button in the dialog box that appears.

Setting up television receivers with a built-in receiver

For this type of equipment, manual tuning of Tricolor TV channels will be required. You can do it yourself by switching the TV to the antenna equipment setup mode. The path to this section may be different, depending on the specific TV model, so you should rely on the instructions included with the equipment.

Settings options

Having entered the desired section, select the “Manual setup” item in the menu, where you set the following equipment parameters:

On – in the “Network search” column;
12226 – in the line “Transponder frequency”;
27500 – in the “Symbol Rate” section;
the name of the standard Tricolor TV satellite is in the “Satellite” section.

These parameters are set using the remote control and saved. Next, they start searching for channels, during which they act based on the clues that appear on the TV screen. Based on the search results, the list of found channels is saved.

Attention! Some TV receiver models with CI+ module do not offer list saving automatically. For them, it will be necessary to clarify in the instructions how the search results are saved.

Free channels

Many fans of freebies are interested in how to set up free Tricolor TV channels. In this case, there are no separate secret instructions. The set of federal channels, which by law are provided free of charge to all television subscribers, will be determined by the receiver during the search procedures described above. Tricolor TV has these channels on the buttons:

from 1 to 4;
7,8,9;

In addition, under button 13 there is a free channel “Promo TV”, where the operator produces free introductory broadcasts from paid channels. Access to this content also does not require special settings.

Residents of remote corners of Russia, namely the European part, can watch TV without interference thanks to Tricolor TV. Correct installation and configuration of Tricolor TV channels is the key to receiving a high-quality satellite signal.

After reading the article to the end, you will be convinced that installing the equipment will not take much time and effort, the main thing is to follow the instructions. And as a result of the work done, you will have Tricolor television and a large number of TV channels.

People who first heard about this television have many questions. The most common of them: “What is Tricolor TV?”, “How to install an antenna?” “How to connect Tricolor?”, “How to set up Tricolor TV yourself?”, “What channels are shown,” “How much does this service cost?” We will try to answer these and other questions below.

This is a new generation of satellite digital television. It provides twenty-five completely free-to-air channels and three radio stations. The satellites involved are Eutelsat 36A, Eutelsat 36B and Bonum-1. What is the essence of digital TV from Tricolor? To expand the television broadcasting territory it is used satellite

. It receives a signal from a terrestrial television station, processes it and feeds it back to the Tricolor TV antenna. After this, the receiver converts the satellite signal, which makes it possible to see colorful images on any TV - LG, Samsung, etc.

Purchase one of the Tricolor packages with self-installation.
Install Tricolor.
Connect the installed device.
Set up the device according to the instructions.
Follow the instructions to register the receiver.

Available channels from Tricolor

Variety of TV packages

Tricolor Television presents several packages.

Basic is a completely free package with 25 channels: all-Russian (Russia 1, Match, NTV, Channel 5, Russia K, Russia 24, Karusel, OTR, TVC, Ren TV, Spas, STS, Domashny, TV-3 , Zvezda, Mir, TNT, Muz-TV, Channel One, Friday), TV shop (SHOP 24), information channels (Promo TV, Infochannel "Tricolor TV", Teleinstructor, TV-TV), as well as three radio stations (Radio Russia, "Vesti FM", Mayak).

The minimum cost of the set is 8800 rubles.

What equipment is included in the Tricolor kit

The basic package includes: a satellite dish and parts for its mounting, a convector, a receiver, a “Start” card, and a cable. You can learn more about all components from our article ““.

Installation steps

Installation of a satellite dish

Installing Tricolor TV is no different from and begins with installing the antenna, which can be entrusted to specialists. This service costs along with setting up the receiver - from 1000 rubles. In principle, this is a small amount. But in order to save on the cost of installing equipment, you can install Tricolor yourself.

The Tricolor antenna should be installed strictly on the south side of the building.

To ensure high-quality communication, take all measures to remove obstacles. The passage of the satellite signal should not be interfered with by any object. The antenna from the receiver should be located no further than 100 meters.

First you need to assemble the antenna according to the instructions. The antenna must be mounted only on a solid surface to which the bracket is attached. At the next stage, the converter is placed inside the holder.

Using a connector, we connect the converter and the cable. The connection diagram is as follows:

We clean the wire from insulation.
We place the braid along the length of the cable.
We place foil along the length of the braid.
Remove 1 cm of internal insulation.
Screw the connector all the way.
We release the conductor located in the center by 0.2 cm.

Using insulation, we attach the cable to the converter holder. To prevent moisture from entering, wrap the F-connector with electrical tape and apply silicone. It's time to attach the antenna to the bracket to which you need to attach the cable.

Connecting the receiver

The antenna is installed, the next step is to connect the receiver. , for example, the Samsung brand, is not at all difficult, the main thing is to follow the instructions. This can be done using a regular or antenna cable. In the first case, the connection will be low-frequency, and for a high-quality connection you need to use an antenna cable (learn more about).

Receiver connection diagram for two TVs

Receiver connection procedure same. First you need to connect the antenna to the receiver using a cable. Plug the device into the outlet and press the “On” button. Using automatic mode, find the channel that says “No Signal.” This will indicate that the receiver is connected correctly.

Next, you should check the strength of the signal supplied from the satellite to the device. Turn on any channel. Please note that there will be no picture yet - you need to adjust the antenna. At this stage, the channel number and name, as well as the time, should light up on the screen.

Settings

Subsequent setup of Tricolor TV involves working with the dish and receiver. To do this, display indicators of signal quality and strength by pressing the “i” button on the remote control. To set up channels , invite a friend/neighbor. One should rotate the satellite dish, and the other should monitor the picture on the screen.

First of all, a mirror installed vertically is adjusted. It needs to be turned smoothly in the horizontal plane. When the scale of signal strength and quality is filled, a picture will appear on the screen of the configured device.

Scheme for setting up an antenna with a mirror

Satellite television "Tricolor TV" has come to many homes in our country. Their kits are in deserved and constant demand among the population due to their high signal quality, low cost and ease of purchase via the Internet. After you purchase a satellite dish and receiver, you can order a full range of installation services for the Tricolor TV television set from a specialized company. In this article you will learn how to install, connect and fully configure the Tricolor TV satellite system yourself.

Assembling the kit

Even a person completely unfamiliar with technology can assemble the purchased kit independently. If you decide to install and configure the dish and receiver yourself, we advise you to study the instructions and remember the names of the components of the satellite dish. You should also understand where exactly and how the Tricolor TV receiver is connected.

Prepare a TV cable with plugs. First of all, we place the converter in the holder.

Pay attention to the connector, it should be directed downward so that raindrops do not flow into it.

The installation coupling should be securely attached to the working area of the converter. Before installing the antenna, we recommend checking and tightening all the bolts again. In order to correctly adjust the head and find the exact direction to the Tricolor TV satellite, this will have to be done more than once during the installation process.

Antenna installation

To obtain a high-quality image on the TV screen coming through the receiver output, it is necessary to accurately tune the antenna to the Tricolor TV satellite and the absence of visible interference on a straight line mentally drawn between them.

Before proceeding with installation, carefully read the documents of the equipment set and find the name of your set there: “Center” or “Siberia”.

The plate should face strictly south, and should be mounted exclusively on an external wall or mast. Under no circumstances can it be installed between high-rise buildings or trees that block the imaginary axis drawn between the dish and the satellite.

If you have decided to install the receiving device yourself on the external wall of the house, then you should secure the bracket with reliable anchors. If this rule is not followed, strong winds can tear off the fastenings and the antenna can cause a lot of trouble. The installation location should be selected based on a simple calculation: as close as possible to the place where the receiver is installed.

Even when using a cable with double braid and thickened copper core, this distance is limited to one hundred meters. If it is impossible to install the kit so closely, we recommend purchasing and setting up an additional amplifier. The process of purchasing it is not complicated; it is usually available in any store that sells television equipment.

After purchase, the antenna is first assembled and installed on an already fixed bracket. We strip the television cable from the top layer of insulation from both ends by one and a half centimeters. In the direction from end to middle, carefully wrap the shielded braid and screw the F-connector onto the freed part. We leave the main copper core protruding two millimeters beyond the connector, and bite off the rest with pliers. Now you need to connect the receiver with a cable going to the antenna converter.

Connecting the receiver

There are two ways to connect the Tricolor TV receiver to your TV yourself:

high-frequency connection with antenna cable;
low-frequency connection of the receiver using a regular cable with “bells” or a “scart” connector.

For an RF connection: plug the cable into the antenna socket of the TV and connect it to the “RF Out” output of the receiver. Then we connect the receiver with a cord to an electrical outlet and turn on the power switch. “BOOT” and the channel number should appear on the screen. Then we launch an automatic channel search in the television receiver and look for a channel with the words “No Signal”, indicating to us that the receiver is connected correctly.

For LF connection: the receiver is connected using a cable with “tulips” or “skart”. We turn on the receiver to the network and wait for the word “BOOT” to appear on the screen, and then the numbers of the channel number. On the control panel of the television receiver, the video mode is set using the “A/V” key. If we see the message “No signal,” then the receiver is connected correctly.

Next, you need to check the presence of a strong signal coming from the satellite to the receiver. We try to display any random channel on the TV. The screen will display the channel number, the program broadcast from the satellite to the dish and the time. Since the antenna is not tuned, the TV screen will have a blue color throughout the background.

We look for the inscription “i” on the receiver’s remote control and turn on this button. Two scales “Signal Strength” and “Signal Quality” should appear on the screen, according to which the settings should be made, and then we will independently configure the satellite dish.

Settings

The last important stage of work required to obtain a high-quality image on the TV is the correct configuration of the satellite dish and the Tricolor TV receiver. This action can be performed independently, keeping the antenna direction strictly south. It is advisable to carry out further steps to establish signal reception from the antenna together with family members or any assistant.

Place it near the TV and wait for commands from it about the result on the screen, independently and little by little turning the satellite dish up and down, right and left, a centimeter at a time.

Having a neighbor's Tricolor TV antenna makes setup much easier. Simply copy its direction and tilt, ensuring that the fields of both scales on the screen are filled as completely as possible.

You need to start adjusting the signal from the vertical position of the dish mirror, gradually moving it in the horizontal plane. We look at the screen: if both scales are full, this means we have caught a good signal. Soon a high-quality image appears on the television receiver. If only one scale is filled, the signal does not come from the ‘Tricolor TV’ satellite, you need to look further. By gradually independently turning the antenna mirror, first horizontally, then vertically, we adjust the maximum filling of the scales and the highest quality image on the TV screen.

Registration

To register the receiver you will need:

Tricolor TV card number;
receiver serial number;
code indicated on the card;
owner's passport;
kit installation address.

The easiest way is to register your receiver number through the Tricolor TV website. After filling out a special registration form, your contract number will be shown in the window and the card will be activated. The agreement can be downloaded from the website, printed, signed and sent to the address indicated on the website by regular mail to the company for signature.

You can register the installation by calling the company phone numbers listed on the website. It will take a little time, and the result will be the same; the contract will be sent to you by mail. The most important thing is that along with the purchase of your favorite TV shows, you receive a guarantee for the entire set of equipment! We wish you that your independent installation and configuration of the Tricolor TV satellite dish and receiver will be successful and that you will be in a good mood as a result of watching interesting television programs!

All you have to do is search and activate your subscription to your favorite tricolor TV channels. Setting up tricolor TV is done following a certain algorithm. And if you follow simple recommendations, you can do it yourself and very soon you will be enjoying watching your favorite TV shows in high quality.

When the television cable is correctly connected to the satellite dish head, you should see the receiver's software interface on the TV screen. When you have installed the set-top box and turned it on, the first thing the receiver will ask you to do is make sound settings and set the language of the main menu.

Next, you should calibrate the video output; to do this, you need to go to the “menu” by pressing the corresponding button on the remote control and select the AV settings item. In the menu you can set the desired picture and sound parameters in accordance with the connection you are using.

If you do not set the video output parameters correctly, the picture from the receiver on the TV will not be displayed correctly. For your convenience, when you turn it on for the first time, it is also recommended to set the date and time by proceeding to the “time setting” item.

To search for the channels themselves, you need to go to the main menu by pressing the “menu” button and find the “automatic tuning” item. The next step is to select the satellite you are tuned to. Select the satellite you need from the list and start an automatic search.

If the sequence of actions is correct, lines should appear on the screen indicating the level and quality of the signal.

Step-by-step instructions for setting up tricolor channels

To configure the receiver, you need to press the “menu” button and select the “setup” item, press the OK button and enter the standard access code 0000. Find the item search for tricolor TV channels and press OK, after scanning is completed, press the OK button to save.

To find and save free TV and radio programs, press “menu”, then “setup”, enter the digital pin code 0000. Go to “automatic search”, set the search type to “network”, select the item “skipping encrypted channels” and press the button to start “search” " After the TV shows have been registered, click save.

This method allows you to find free channels and those channels that are not included in the tricolor TV package. Among them you will find free channels, usually from foreign telecom operators, which are rebroadcast via satellite.

Sorting TV channels

Once you have completed your search, you can begin sorting according to your tastes. To sort in alphabetical order, you can use the OK button on the remote control and call up the channel list. After clicking on the green button in the open window, you will see a column in which you can select a specific letter. When you select the desired letter and click on the OK button on the right, you will see all the channels that begin with the selected letter.

The software shell of your receiver allows you to create lists of favorite TV shows, this is very convenient, you don’t have to sit and look for your favorite channel among hundreds of others. The standard firmware already has four lists:

Music
News
Sport
Movies

Lists of favorite TV channels can be edited; delete, rename or rearrange. If you want to distribute TV channels according to lists, you need to do the following. Click on the Fav button and call up the list, click on the OK button and in the window that appears, select your favorite TV channel, for example music. After selecting, while on the TV channel, press the OK button again, and your favorite TV channel appears in the list of favorite “Music” channels.

Thus, you can distribute all channels into lists, this is very convenient. To change favorite lists, just click on the blue button.

Free tricolor TV services

In addition, the tricolor company also provides free services. These include:

An electronic TV guide is a convenient program guide that displays the start time of the TV show and the end time, title and brief description. You can call up a useful function by pressing the EPG button on the remote control.

Telechat is a special tricolor window, which is usually located at the bottom of the TV screen. Telechat supports sending short messages from your mobile phone, tablet or computer.

Karaoke is an innovation of the tricolor company, which can be found on the tricolor TV info channel. Every evening through the channel there is a broadcast of musical soundtracks accompanied by captions of familiar compositions.

Problems that may arise when you first turn on and configure tricolor TV

A common problem when first turned on is the lack of signal. If a similar message appears on the TV screen, first of all you should check the power supply to the receiver. After this, you need to make sure that the contacts of all cables and connectors are reliable. The problem may be in choosing the wrong signal source; you should press the AV button on the TV remote control several times.

The message “no signal” may appear on the screen, but at the same time the access menu to the tricolor TV channel opens. In this case, two options are possible: either maintenance work is being carried out on the channel, or your antenna, for example, has lost tuning after a strong wind.

If the message “encrypted channel” appears on the screen, the reason may be a late payment, or you forgot to register your receiver. To register, you need to go to the official website of Tricolor TV and go through a simple procedure. The reason for the appearance of the hated sign may be that the receiver is frozen; in this case, you need to reboot the receiver. Completely unplug it from the outlet, wait 5 - 10 seconds and turn it on again.

If you find an inscription on the screen “DRE encrypted channel”, and before that, all channels opened, this may mean that your receiver has been standing for several days and the keys from the satellite have not been updated. In this case, you need to tune in to one of the federal channels and leave the receiver on until the channels open.